Kodak A-61092 manual Enabling bar code reading, Enabling the bar code confirma- tion tone

Page 76

Enabling bar code reading

Enabling the bar code confirma- tion tone

Make sure that Bar Code Reading is enabled before feeding documents.

To enable Bar Code Reading at the mode level:

∙Enter function code F60.

Partial Bar Code Reading allows the scanner to read bar codes with a start character (and n characters beyond the start character that can be read) even if no end character is encountered.

To enable Partial Bar Code Reading:

∙Enter function code F66.

NOTE: Partial Bar Code Reading can only be enabled (or disabled) if Bar Code Reading is enabled at the mode level.

If you have enabled the Bar Code Reader, but do not want to read/decode bar code(s) found on the next document only, perform function code F64.

The bar code confirmation tone may be used to signal that a bar code has been read.

∙If your scanner is configured for no confirmation tones, then no confirmation tones of any kind will be heard in any mode.

∙If your scanner is configured to allow confirmation tones, then you can disable (or enable) confirmation tones in any mode as desired.

If the confirmation tones and the bar code confirmation tone are enabled during installation for the mode being used, you may enable/disable the bar code confirmation tone during normal operations by performing function code F63.

In addition, a bar code/patch confirmation tone may be used to signal that both a bar code and a patch have been detected. This confirmation tone may be enabled or disabled by performing function code F62.

NOTE: Patch Code Reading must be enabled in the scanner in order to use this feature.

8-8	A-61092 September 1999

Image 76

Contents User’s Guide Page Page Scanner features IntroductionScanner options September Rear view September Key/Indicator Operating keys and indicatorsFunction Keys/Indicators Next Turning on the scanner Getting StartedSelecting the language display Calibrating the scanner Preparing documents for scanning Unsuccessful calibrationAdjusting the feed and separator roller Gap semi-automatic feeder onlyTurn the gap adjustment knob counterclockwise 2 1/2 turns Adjusting the feed shelf position semi Automatic feeder onlySemi-automatic feeder only Adjusting the feed shelf side guidesFeed Shelf Label Adjusting the exit hopper side guides and end stop Changing the deflector Operating the Scanner OverviewSelecting a mode Temporary operating values Feeding documents using the semi- automatic feeder Feeding thick documents Feeding documents using the automatic feeder Using function codes Function CodesFunction code summary Footswitch OperationScanning EndorserSuper12 Document Printer Patch ReaderFunction Code Name CodeDescription F17 F18 F19 F20 F21 F22 F23 F34 F37 F38 F39 Code Function Code Name Enter F58 F59 F60 F62 F63 F64 F65 F66 F70 F71 F72 F73 F74 F75 F91 F92 F93 F94 F95 F96 F97 F98 F99 Maintenance Cleaning tasks Cleaning materials Replacement partsDaily maintenance procedures Cleaning the imaging guidesSeptember Roller cover Release lever Feed roller Separator roller Cleaning the feeder module and separator roller Cleaning the separator roller Cleaning the paper path Vacuuming inside the scanner September September Cleaning the exposure lamp housings Weekly maintenance proceduresCleaning the cabinet Monthly maintenance procedures Cleaning the air filterReplacement procedures Replacing the air filterReplacing the exposure lamps September Replacing the imaging guides Replacing the feeder module and separator roller Replacing the feeder moduleReplacing the separator roller Ordering replacement parts Ordering cleaning materials Operator Messages Code Operator Message Displayed Operator message listingDescription/Action Required Code Code Code E281 E282 E285 E286 E291 E293 E294 E295 E296 E297 E298 Code Various messages Troubleshooting Trouble and remedy chartTrouble Probable CauseTrouble Clearing the document path Document pathClearing documents Feeder/horizontal transport area Imaging guide area Lower roller assembly area Vertical transport area Upper turn area Document exit area Accessories Supply Catalog # SuppliesImaging Station Lamps Supply Catalog # Parts and tools Part/ToolUnited States and Canada Order Number All other regionsUsing the Bar Code Reader Bar code types Code TypeCharacter Set Available Characters in Set Start/Stop CharactersBar code placement Before you begin Enabling bar code reading Enabling the bar code confirma- tion tonePerforming a bar code test September Using the Evaluate option Static bar code evaluationSelect 1=EVALUATE Select either 1=Transport Off or 2=Transport OnUsing the Imaging Station Cutting line 12.5 mm Dynamic bar code evaluation Dimensional Fields Pass or Fail Evaluating test resultsReflectance Fields Grades a through F Grade Field Pass 31 to FailCommon Causes of Low Bar Code Ratings Field Problem TypeCause Using the Display option Using the %KODAK optionUsing the %NORM option September Using the Check Feeder / Check Stacker Using the check feederClearing jams in the check feeder Cleaning the check feeder Using the check stacker Using the Endorser Die stylesBefore you begin Changing the die drum Endorser Locking lever Latch Endorser rotates to the right Die Spring clip Pry off at this edge Changing the ink roller Setting the date and code number Selecting the Endorser mode Enabling Endorser Changing the print positionUsing the Footswitch Enabling the confirmation tone Footswitch Pressed actions Footswitch Pressed ActionFootswitch Pressed Definition Footswitch Released actionsFootswitch Released Action Using the Patch Reader Patch typesPatch code placement Positioning the Patch Reader Sensor Modes Appendix a Basic ConceptsLinked modes Image addresses Assigning an image address Using the Next key∙ Enter Using Function Code F92 Indexing schemes Image address formatsSingle level indexing Two level indexing Image Address Three level indexing Three level offset indexing Controlling document level changes Level instructionDocument A G I N G