Kodak A-61092 manual Using the Evaluate option, Static bar code evaluation, Select 1=EVALUATE

Page 79

Using the Evaluate option

Static bar code evaluation

Use the Evaluate option when you want to measure the quality of the bar codes being used by evaluating specific bar code characteristics.

The Evaluate option allows you to perform a Static Bar Code Evaluation test or a Dynamic Bar Code Evaluation test.

∙Static Bar Code Evaluation — is performed if you want to just verify how well the Bar Code Reader is working. This test is performed with the transport off.

∙Dynamic Bar Code Evaluation — is performed if you want to verify how well the Bar Code Reader is working and the speed of the Bar Code Reader. This test is performed with the transport on. Unlike the Static Bar Code Evaluation, the results of this test can be influenced by the motion of the document. If less than satisfactory results are obtained, perform the evaluation again using the Static Bar Code Evaluation.

To use the Evaluate option:

1.Select 1=EVALUATE.

Bar Code Type =

1=EVALUATE 2=DISPLAY 3=%KODAK 4=%NORM

2.Select either 1=Transport Off or 2=Transport On.

1=Transport Off 2=Transport On

If you select 1=Transport Off, proceed to the next section entitled, “Static bar code evaluation”. If you select 2=Transport On, proceed to the section entitled, “Dynamic bar code evaluation”.

Static Bar Code Evaluation allows you to verify how well your Bar Code Reader is working. This test is performed with the transport off. Follow the procedures below to perform the Static Bar Code Evaluation test.

After selecting option 1=Transport Off, the following message is displayed:

Bar Code Type=

Place bar code under the scan head

∙Place the bar code is placed directly under the imaging station for evaluation.

A-61092 September 1999

8-11

Image 79

Contents User’s Guide Page Page Introduction Scanner featuresScanner options September Rear view September Key/Indicator Operating keys and indicatorsFunction Keys/Indicators Next Turning on the scanner Getting StartedSelecting the language display Calibrating the scanner Unsuccessful calibration Preparing documents for scanningGap semi-automatic feeder only Adjusting the feed and separator rollerTurn the gap adjustment knob counterclockwise 2 1/2 turns Automatic feeder only Adjusting the feed shelf position semiSemi-automatic feeder only Adjusting the feed shelf side guidesFeed Shelf Label Adjusting the exit hopper side guides and end stop Changing the deflector Overview Operating the ScannerSelecting a mode Temporary operating values Feeding documents using the semi- automatic feeder Feeding thick documents Feeding documents using the automatic feeder Function Codes Using function codesFunction code summary Endorser FootswitchOperation ScanningPatch Reader Super12 Document PrinterFunction Code Name CodeDescription F17 F18 F19 F20 F21 F22 F23 F34 F37 F38 F39 Code Function Code Name Enter F58 F59 F60 F62 F63 F64 F65 F66 F70 F71 F72 F73 F74 F75 F91 F92 F93 F94 F95 F96 F97 F98 F99 Cleaning tasks Cleaning materials Replacement parts MaintenanceCleaning the imaging guides Daily maintenance proceduresSeptember Roller cover Release lever Feed roller Separator roller Cleaning the feeder module and separator roller Cleaning the separator roller Cleaning the paper path Vacuuming inside the scanner September September Cleaning the exposure lamp housings Weekly maintenance proceduresCleaning the cabinet Cleaning the air filter Monthly maintenance proceduresReplacing the air filter Replacement proceduresReplacing the exposure lamps September Replacing the imaging guides Replacing the feeder module Replacing the feeder module and separator rollerReplacing the separator roller Ordering replacement parts Ordering cleaning materials Operator Messages Code Operator Message Displayed Operator message listingDescription/Action Required Code Code Code E281 E282 E285 E286 E291 E293 E294 E295 E296 E297 E298 Code Various messages Probable Cause TroubleshootingTrouble and remedy chart TroubleTrouble Document path Clearing the document pathClearing documents Feeder/horizontal transport area Imaging guide area Lower roller assembly area Vertical transport area Upper turn area Document exit area Accessories Supply Catalog # SuppliesImaging Station Lamps Supply Catalog # All other regions Parts and toolsPart/Tool United States and Canada Order NumberUsing the Bar Code Reader Available Characters in Set Start/Stop Characters Bar code typesCode Type Character SetBar code placement Before you begin Enabling the bar code confirma- tion tone Enabling bar code readingPerforming a bar code test September Select either 1=Transport Off or 2=Transport On Using the Evaluate optionStatic bar code evaluation Select 1=EVALUATEUsing the Imaging Station Cutting line 12.5 mm Dynamic bar code evaluation Evaluating test results Dimensional Fields Pass or FailGrade Field Pass 31 to Fail Reflectance Fields Grades a through FCommon Causes of Low Bar Code Ratings Field Problem TypeCause Using the %KODAK option Using the Display optionUsing the %NORM option September Using the check feeder Using the Check Feeder / Check StackerClearing jams in the check feeder Cleaning the check feeder Using the check stacker Die styles Using the EndorserBefore you begin Changing the die drum Endorser Locking lever Latch Endorser rotates to the right Die Spring clip Pry off at this edge Changing the ink roller Setting the date and code number Enabling Endorser Changing the print position Selecting the Endorser modeUsing the Footswitch Footswitch Pressed Action Enabling the confirmation tone Footswitch Pressed actionsFootswitch Pressed Definition Footswitch Released actionsFootswitch Released Action Patch types Using the Patch ReaderPatch code placement Positioning the Patch Reader Sensor Modes Appendix a Basic ConceptsLinked modes Image addresses Assigning an image address Using the Next key∙ Enter Using Function Code F92 Image address formats Indexing schemesSingle level indexing Two level indexing Image Address Three level indexing Three level offset indexing Level instruction Controlling document level changesDocument A G I N G