Kodak A-61092 manual Code

Page 58

Code

E230

E231

E232

E234

E235

E236

E238

E240

E241

E242

E243

E244

E245

E246

E267

E280

Operator Message Displayed

Open access door to correct error

Press JOG, and try again

Close all access doors and RUN

Press JOG, and try again

Turn main power OFF and ON

User function string invalid

Enter correct level of IA — refeed

Conflicting input — what level?

Clear error, re-enter IA

Feeder off due to host request

Description/Action Required

Open the access door.

Verify all operator accessible areas are properly closed.

Press Run to continue.

Press Jog and then press the Run key. Try again.

Close all access doors.

Press Run to continue.

Press the Jog key and then press Run. Try again.

∙Turn the side panel switch off.

∙Turn the main power switch off.

∙Wait 5 to 10 seconds.

∙Turn the main power switch on.

∙Turn the side panel switch on. If the error repeats, call service.

The P-key, End-of-Batch, etc., definition made during installation is invalid. Correct the definition using the Mode Setup Software.

Set or change the document image level or use the Next key to enter a new image address.

Press Run to continue.

Set or change the document image level to confirm the proper document image level.

Press Run to continue.

Press Clear. Use the Next key to enter an image address.

Press Run to continue.

System is busy. The feeder will be reactivated when the system is no longer busy.

Wait until the message clears and continue.

A-61092 September 1999

6-5

Image 58

Contents User’s Guide Page Page Scanner features IntroductionScanner options September Rear view September Key/Indicator Operating keys and indicatorsFunction Keys/Indicators Next Turning on the scanner Getting StartedSelecting the language display Calibrating the scanner Preparing documents for scanning Unsuccessful calibrationAdjusting the feed and separator roller Gap semi-automatic feeder onlyTurn the gap adjustment knob counterclockwise 2 1/2 turns Adjusting the feed shelf position semi Automatic feeder onlySemi-automatic feeder only Adjusting the feed shelf side guidesFeed Shelf Label Adjusting the exit hopper side guides and end stop Changing the deflector Operating the Scanner OverviewSelecting a mode Temporary operating values Feeding documents using the semi- automatic feeder Feeding thick documents Feeding documents using the automatic feeder Using function codes Function CodesFunction code summary Scanning FootswitchOperation EndorserSuper12 Document Printer Patch ReaderFunction Code Name CodeDescription F17 F18 F19 F20 F21 F22 F23 F34 F37 F38 F39 Code Function Code Name Enter F58 F59 F60 F62 F63 F64 F65 F66 F70 F71 F72 F73 F74 F75 F91 F92 F93 F94 F95 F96 F97 F98 F99 Maintenance Cleaning tasks Cleaning materials Replacement partsDaily maintenance procedures Cleaning the imaging guidesSeptember Roller cover Release lever Feed roller Separator roller Cleaning the feeder module and separator roller Cleaning the separator roller Cleaning the paper path Vacuuming inside the scanner September September Cleaning the exposure lamp housings Weekly maintenance proceduresCleaning the cabinet Monthly maintenance procedures Cleaning the air filterReplacement procedures Replacing the air filterReplacing the exposure lamps September Replacing the imaging guides Replacing the feeder module and separator roller Replacing the feeder moduleReplacing the separator roller Ordering replacement parts Ordering cleaning materials Operator Messages Code Operator Message Displayed Operator message listingDescription/Action Required Code Code Code E281 E282 E285 E286 E291 E293 E294 E295 E296 E297 E298 Code Various messages Trouble TroubleshootingTrouble and remedy chart Probable CauseTrouble Clearing the document path Document pathClearing documents Feeder/horizontal transport area Imaging guide area Lower roller assembly area Vertical transport area Upper turn area Document exit area Accessories Supply Catalog # SuppliesImaging Station Lamps Supply Catalog # United States and Canada Order Number Parts and toolsPart/Tool All other regionsUsing the Bar Code Reader Character Set Bar code typesCode Type Available Characters in Set Start/Stop CharactersBar code placement Before you begin Enabling bar code reading Enabling the bar code confirma- tion tonePerforming a bar code test September Select 1=EVALUATE Using the Evaluate optionStatic bar code evaluation Select either 1=Transport Off or 2=Transport OnUsing the Imaging Station Cutting line 12.5 mm Dynamic bar code evaluation Dimensional Fields Pass or Fail Evaluating test resultsReflectance Fields Grades a through F Grade Field Pass 31 to FailCommon Causes of Low Bar Code Ratings Field Problem TypeCause Using the Display option Using the %KODAK optionUsing the %NORM option September Using the Check Feeder / Check Stacker Using the check feederClearing jams in the check feeder Cleaning the check feeder Using the check stacker Using the Endorser Die stylesBefore you begin Changing the die drum Endorser Locking lever Latch Endorser rotates to the right Die Spring clip Pry off at this edge Changing the ink roller Setting the date and code number Selecting the Endorser mode Enabling Endorser Changing the print positionUsing the Footswitch Enabling the confirmation tone Footswitch Pressed actions Footswitch Pressed ActionFootswitch Pressed Definition Footswitch Released actionsFootswitch Released Action Using the Patch Reader Patch typesPatch code placement Positioning the Patch Reader Sensor Modes Appendix a Basic ConceptsLinked modes Image addresses Assigning an image address Using the Next key∙ Enter Using Function Code F92 Indexing schemes Image address formatsSingle level indexing Two level indexing Image Address Three level indexing Three level offset indexing Controlling document level changes Level instructionDocument A G I N G