Kodak A-61092 manual Clearing documents Feeder/horizontal transport area

Page 65

Clearing documents

The feeder/horizontal transport area

Follow the steps below to clear the document path:

1.Check each transport area (Areas A through F) for documents lodged in the document path. You only have to remove the jammed document(s). The Jog feature places the rest of the documents in the exit hopper. Make certain all operator-accessible areas are firmly closed and all baffle plates are locked into place.

2.Press and hold down the Jog key to clear any remaining documents.

3.Collect the documents located in the transport system. Put them back into their original order, if necessary.

4.Reset the image address, level, etc., if necessary.

5.Rescan the documents. If an error code appears in the status display, check each transport area again to make certain all documents have been cleared.

NOTE: Green labels on handles designate operator-accessible areas.

To clear the feeder/horizontal transport area (Area A):

1.Grasp the front cover and swing it open to the right.

2.Push the roller cover release lever toward the rear of the machine.

Roller cover

Roller cover release lever

				Gap
				release
	Feed roller			release
	Feed roller			lever
				lever


Separator roller

3.Grasp the roller cover and rotate it up and toward the back of the machine.

4.Remove any documents or document pieces found in the feeder.

5.Grasp and rotate the roller cover back into its original position.

6.Verify that the roller cover release lever snaps back and locks the roller cover down into position.

7.Close the front cover.

7-4	A-61092 September 1999

Image 65

Contents User’s Guide Page Page Introduction Scanner featuresScanner options September Rear view September Function Operating keys and indicatorsKey/Indicator Keys/Indicators Next Selecting the language display Getting StartedTurning on the scanner Calibrating the scanner Unsuccessful calibration Preparing documents for scanningGap semi-automatic feeder only Adjusting the feed and separator rollerTurn the gap adjustment knob counterclockwise 2 1/2 turns Automatic feeder only Adjusting the feed shelf position semiFeed Shelf Label Adjusting the feed shelf side guidesSemi-automatic feeder only Adjusting the exit hopper side guides and end stop Changing the deflector Overview Operating the ScannerSelecting a mode Temporary operating values Feeding documents using the semi- automatic feeder Feeding thick documents Feeding documents using the automatic feeder Function Codes Using function codesFunction code summary Operation FootswitchScanning EndorserPatch Reader Super12 Document PrinterDescription CodeFunction Code Name F17 F18 F19 F20 F21 F22 F23 F34 F37 F38 F39 Code Function Code Name Enter F58 F59 F60 F62 F63 F64 F65 F66 F70 F71 F72 F73 F74 F75 F91 F92 F93 F94 F95 F96 F97 F98 F99 Cleaning tasks Cleaning materials Replacement parts MaintenanceCleaning the imaging guides Daily maintenance proceduresSeptember Roller cover Release lever Feed roller Separator roller Cleaning the feeder module and separator roller Cleaning the separator roller Cleaning the paper path Vacuuming inside the scanner September September Cleaning the cabinet Weekly maintenance proceduresCleaning the exposure lamp housings Cleaning the air filter Monthly maintenance proceduresReplacing the air filter Replacement proceduresReplacing the exposure lamps September Replacing the imaging guides Replacing the feeder module Replacing the feeder module and separator rollerReplacing the separator roller Ordering replacement parts Ordering cleaning materials Operator Messages Description/Action Required Operator message listingCode Operator Message Displayed Code Code Code E281 E282 E285 E286 E291 E293 E294 E295 E296 E297 E298 Code Various messages Trouble and remedy chart TroubleshootingTrouble Probable CauseTrouble Document path Clearing the document pathClearing documents Feeder/horizontal transport area Imaging guide area Lower roller assembly area Vertical transport area Upper turn area Document exit area Accessories Imaging Station Lamps Supply Catalog # SuppliesSupply Catalog # Part/Tool Parts and toolsUnited States and Canada Order Number All other regionsUsing the Bar Code Reader Code Type Bar code typesCharacter Set Available Characters in Set Start/Stop CharactersBar code placement Before you begin Enabling the bar code confirma- tion tone Enabling bar code readingPerforming a bar code test September Static bar code evaluation Using the Evaluate optionSelect 1=EVALUATE Select either 1=Transport Off or 2=Transport OnUsing the Imaging Station Cutting line 12.5 mm Dynamic bar code evaluation Evaluating test results Dimensional Fields Pass or FailGrade Field Pass 31 to Fail Reflectance Fields Grades a through FCause Problem TypeCommon Causes of Low Bar Code Ratings Field Using the %KODAK option Using the Display optionUsing the %NORM option September Using the check feeder Using the Check Feeder / Check StackerClearing jams in the check feeder Cleaning the check feeder Using the check stacker Die styles Using the EndorserBefore you begin Changing the die drum Endorser Locking lever Latch Endorser rotates to the right Die Spring clip Pry off at this edge Changing the ink roller Setting the date and code number Enabling Endorser Changing the print position Selecting the Endorser modeUsing the Footswitch Footswitch Pressed Action Enabling the confirmation tone Footswitch Pressed actionsFootswitch Released Action Footswitch Released actionsFootswitch Pressed Definition Patch types Using the Patch ReaderPatch code placement Positioning the Patch Reader Sensor Linked modes Appendix a Basic ConceptsModes Image addresses ∙ Enter Using the Next keyAssigning an image address Using Function Code F92 Image address formats Indexing schemesSingle level indexing Two level indexing Image Address Three level indexing Three level offset indexing Level instruction Controlling document level changesDocument A G I N G