Kodak A-61092 manual Code

Page 56

Code

E121

E122

E123

E124

E125

E126

E127

E128

E130

E131

E132

E133

E140

E141

E142

E143

E145

E200

E201

Operator Message Displayed

Check front patch reader

Check rear patch reader

Command data rejected — resend

Command not allowed in this model

Enter correct command

Feeder waiting for host system

Feeder adjustment warning

OCR not installed

Device not enabled

Enable bar code first

Feeder waiting for printer (Super 12 Printer only)

Document Printer not installed Patch Reader not installed Detection System not installed Bar Code Reader not installed Endorser not installed

Verify/enter image address

Description/Action Required

Patch code not recognized.

Verify that the patch document was fed into the transport in the proper orientation.

∙If not, refeed the path document.

∙If so, change to a non-patch mode to continue; call service.

Command not recognized. Enter the command again.

Command cannot be performed. Enter a valid command.

Press correct key(s) for mode selected.

System is busy. No action required. Wait for the message to clear.

Check and adjust feed and separator roller gap.

Requested action requires installation of the OCR accessory.

Requested action requires installation of the Bar Code Reader.

Requested action requires that you enable the Bar Code Reader. Enter function code F60 to enable bar code reading.

The printer is moving into the print position; wait until the message clears.

Requested action required installation of the module/accessory indicated.

The required module/accessory is not installed.

An error has occurred in the system and the image address may no longer be correct.

Use function code F08 to determine the last image address.

Use the Next key to correct the image address, if necessary.

A-61092 September 1999

6-3

Image 56

Contents User’s Guide Page Page Scanner features IntroductionScanner options September Rear view September Function Operating keys and indicatorsKey/Indicator Keys/Indicators Next Selecting the language display Getting StartedTurning on the scanner Calibrating the scanner Preparing documents for scanning Unsuccessful calibrationAdjusting the feed and separator roller Gap semi-automatic feeder onlyTurn the gap adjustment knob counterclockwise 2 1/2 turns Adjusting the feed shelf position semi Automatic feeder onlyFeed Shelf Label Adjusting the feed shelf side guidesSemi-automatic feeder only Adjusting the exit hopper side guides and end stop Changing the deflector Operating the Scanner OverviewSelecting a mode Temporary operating values Feeding documents using the semi- automatic feeder Feeding thick documents Feeding documents using the automatic feeder Using function codes Function CodesFunction code summary Footswitch OperationScanning EndorserSuper12 Document Printer Patch ReaderDescription CodeFunction Code Name F17 F18 F19 F20 F21 F22 F23 F34 F37 F38 F39 Code Function Code Name Enter F58 F59 F60 F62 F63 F64 F65 F66 F70 F71 F72 F73 F74 F75 F91 F92 F93 F94 F95 F96 F97 F98 F99 Maintenance Cleaning tasks Cleaning materials Replacement partsDaily maintenance procedures Cleaning the imaging guidesSeptember Roller cover Release lever Feed roller Separator roller Cleaning the feeder module and separator roller Cleaning the separator roller Cleaning the paper path Vacuuming inside the scanner September September Cleaning the cabinet Weekly maintenance proceduresCleaning the exposure lamp housings Monthly maintenance procedures Cleaning the air filterReplacement procedures Replacing the air filterReplacing the exposure lamps September Replacing the imaging guides Replacing the feeder module and separator roller Replacing the feeder moduleReplacing the separator roller Ordering replacement parts Ordering cleaning materials Operator Messages Description/Action Required Operator message listingCode Operator Message Displayed Code Code Code E281 E282 E285 E286 E291 E293 E294 E295 E296 E297 E298 Code Various messages Troubleshooting Trouble and remedy chartTrouble Probable CauseTrouble Clearing the document path Document pathClearing documents Feeder/horizontal transport area Imaging guide area Lower roller assembly area Vertical transport area Upper turn area Document exit area Accessories Imaging Station Lamps Supply Catalog # SuppliesSupply Catalog # Parts and tools Part/ToolUnited States and Canada Order Number All other regionsUsing the Bar Code Reader Bar code types Code TypeCharacter Set Available Characters in Set Start/Stop CharactersBar code placement Before you begin Enabling bar code reading Enabling the bar code confirma- tion tonePerforming a bar code test September Using the Evaluate option Static bar code evaluationSelect 1=EVALUATE Select either 1=Transport Off or 2=Transport OnUsing the Imaging Station Cutting line 12.5 mm Dynamic bar code evaluation Dimensional Fields Pass or Fail Evaluating test resultsReflectance Fields Grades a through F Grade Field Pass 31 to FailCause Problem TypeCommon Causes of Low Bar Code Ratings Field Using the Display option Using the %KODAK optionUsing the %NORM option September Using the Check Feeder / Check Stacker Using the check feederClearing jams in the check feeder Cleaning the check feeder Using the check stacker Using the Endorser Die stylesBefore you begin Changing the die drum Endorser Locking lever Latch Endorser rotates to the right Die Spring clip Pry off at this edge Changing the ink roller Setting the date and code number Selecting the Endorser mode Enabling Endorser Changing the print positionUsing the Footswitch Enabling the confirmation tone Footswitch Pressed actions Footswitch Pressed ActionFootswitch Released Action Footswitch Released actionsFootswitch Pressed Definition Using the Patch Reader Patch typesPatch code placement Positioning the Patch Reader Sensor Linked modes Appendix a Basic ConceptsModes Image addresses ∙ Enter Using the Next keyAssigning an image address Using Function Code F92 Indexing schemes Image address formatsSingle level indexing Two level indexing Image Address Three level indexing Three level offset indexing Controlling document level changes Level instructionDocument A G I N G