Kodak A-61092 manual Operator message listing, Code Operator Message Displayed

Page 55

Operator message listing

Code	Operator Message Displayed

E000 Memory battery low — call service

E100 Please wait

E101	Auto shut off, press RUN

E102	Press STOP and try again

E103	Select valid mode

E104	Function not available

E106	Warning — document length error

E107	Warning — skewed document
E110	Upper lamp warning, press RUN

E111	Lower lamp warning, press RUN

E112 Invalid patch level

E113 Enter correct image address

E114	Check current level

E117	Enter correct level/Image Address
E118
E119

E120	Diagnostic running — do not use

Description/Action Required

Call service — do not turn off the machine.

No action required. Wait for the message to clear.

Press Run to continue. Feed documents.

Press Stop and try again.

Invalid mode selected. Enter function code F01 to select another mode.

Invalid function code entered. Enter another function code.

Check the document length to see if it is shorter than the minimum or longer than the maximum allowed; refeed the document.

Refeed the document.

Press Run to continue.

Change the lamps when the current set of documents has been processed.

Press Run to continue.

Change the lamps when the current set of documents has been processed.

Invalid patch was used. Feed correct patch.

Use the Next key to enter correct image address.

Check the current document image level.

Conflicting input regarding the proper level was received.

Document image level assignment and next image address input conflict.

Specify another document image level, or use the Next key to enter a valid image address.

Do not use; the machine is being serviced.

6-2	A-61092 September 1999

Image 55

Contents User’s Guide Page Page Introduction Scanner featuresScanner options September Rear view September Key/Indicator Operating keys and indicatorsFunction Keys/Indicators Next Turning on the scanner Getting StartedSelecting the language display Calibrating the scanner Unsuccessful calibration Preparing documents for scanningGap semi-automatic feeder only Adjusting the feed and separator rollerTurn the gap adjustment knob counterclockwise 2 1/2 turns Automatic feeder only Adjusting the feed shelf position semiSemi-automatic feeder only Adjusting the feed shelf side guidesFeed Shelf Label Adjusting the exit hopper side guides and end stop Changing the deflector Overview Operating the ScannerSelecting a mode Temporary operating values Feeding documents using the semi- automatic feeder Feeding thick documents Feeding documents using the automatic feeder Function Codes Using function codesFunction code summary Endorser FootswitchOperation ScanningPatch Reader Super12 Document PrinterFunction Code Name CodeDescription F17 F18 F19 F20 F21 F22 F23 F34 F37 F38 F39 Code Function Code Name Enter F58 F59 F60 F62 F63 F64 F65 F66 F70 F71 F72 F73 F74 F75 F91 F92 F93 F94 F95 F96 F97 F98 F99 Cleaning tasks Cleaning materials Replacement parts MaintenanceCleaning the imaging guides Daily maintenance proceduresSeptember Roller cover Release lever Feed roller Separator roller Cleaning the feeder module and separator roller Cleaning the separator roller Cleaning the paper path Vacuuming inside the scanner September September Cleaning the exposure lamp housings Weekly maintenance proceduresCleaning the cabinet Cleaning the air filter Monthly maintenance proceduresReplacing the air filter Replacement proceduresReplacing the exposure lamps September Replacing the imaging guides Replacing the feeder module Replacing the feeder module and separator rollerReplacing the separator roller Ordering replacement parts Ordering cleaning materials Operator Messages Code Operator Message Displayed Operator message listingDescription/Action Required Code Code Code E281 E282 E285 E286 E291 E293 E294 E295 E296 E297 E298 Code Various messages Probable Cause TroubleshootingTrouble and remedy chart TroubleTrouble Document path Clearing the document pathClearing documents Feeder/horizontal transport area Imaging guide area Lower roller assembly area Vertical transport area Upper turn area Document exit area Accessories Supply Catalog # SuppliesImaging Station Lamps Supply Catalog # All other regions Parts and toolsPart/Tool United States and Canada Order NumberUsing the Bar Code Reader Available Characters in Set Start/Stop Characters Bar code typesCode Type Character SetBar code placement Before you begin Enabling the bar code confirma- tion tone Enabling bar code readingPerforming a bar code test September Select either 1=Transport Off or 2=Transport On Using the Evaluate optionStatic bar code evaluation Select 1=EVALUATEUsing the Imaging Station Cutting line 12.5 mm Dynamic bar code evaluation Evaluating test results Dimensional Fields Pass or FailGrade Field Pass 31 to Fail Reflectance Fields Grades a through FCommon Causes of Low Bar Code Ratings Field Problem TypeCause Using the %KODAK option Using the Display optionUsing the %NORM option September Using the check feeder Using the Check Feeder / Check StackerClearing jams in the check feeder Cleaning the check feeder Using the check stacker Die styles Using the EndorserBefore you begin Changing the die drum Endorser Locking lever Latch Endorser rotates to the right Die Spring clip Pry off at this edge Changing the ink roller Setting the date and code number Enabling Endorser Changing the print position Selecting the Endorser modeUsing the Footswitch Footswitch Pressed Action Enabling the confirmation tone Footswitch Pressed actionsFootswitch Pressed Definition Footswitch Released actionsFootswitch Released Action Patch types Using the Patch ReaderPatch code placement Positioning the Patch Reader Sensor Modes Appendix a Basic ConceptsLinked modes Image addresses Assigning an image address Using the Next key∙ Enter Using Function Code F92 Image address formats Indexing schemesSingle level indexing Two level indexing Image Address Three level indexing Three level offset indexing Level instruction Controlling document level changesDocument A G I N G