Kodak A-61092 manual E281 E282 E285 E286 E291 E293 E294 E295 E296 E297 E298

Page 59

Code

E281

E282

E285

E286

E291

E293

E294

E295

E296

E297

E298

Operator Message Displayed

OCR was reset — restart batch

Comm buffer full — please wait

Feeder off due to OCR request

Feed calibration target

Scanner disabled

Host recovery required

Front calibration warning

Rear calibration warning

Target not seen

Document queue full

Calibration required

Description/Action Required

Use the Next key to enter a starting image address.

Rerun the batch.

System is busy. Wait until the message clears, then continue.

System is busy. Feeder will be reactivated when the system is no longer busy.

Wait until the message clears, then continue.

Calibration process has started.

Press Run and feed the calibration target into the transport.

The machine has been disabled due to an error. Determine the cause of the error via the host system.

Enable the machine.

Press Run to continue.

Contact your system administrator to initiate the required action on the host system.

Perform maintenance/cleaning procedures for the Document Scanning Array, imaging guides, etc.

Check the lamps; replace if necessary.

Recalibrate the machine.

Perform maintenance/cleaning procedures for the Document Scanning Array, imaging guides, etc.

Check the lamps; replace if necessary.

Recalibrate the machine.

Repeat the calibration process using a blank target. If error repeats, call service.

The feeder and transport are stopped and the machine is disabled.

Transfer images from the image buffer to the host system.

Re-enable the machine.

Press Run to continue.

Enter function code F37 to initiate the calibration sequence.

6-6	A-61092 September 1999

Image 59

Contents User’s Guide Page Page Introduction Scanner featuresScanner options September Rear view September Function Operating keys and indicatorsKey/Indicator Keys/Indicators Next Selecting the language display Getting StartedTurning on the scanner Calibrating the scanner Unsuccessful calibration Preparing documents for scanningGap semi-automatic feeder only Adjusting the feed and separator rollerTurn the gap adjustment knob counterclockwise 2 1/2 turns Automatic feeder only Adjusting the feed shelf position semiFeed Shelf Label Adjusting the feed shelf side guidesSemi-automatic feeder only Adjusting the exit hopper side guides and end stop Changing the deflector Overview Operating the ScannerSelecting a mode Temporary operating values Feeding documents using the semi- automatic feeder Feeding thick documents Feeding documents using the automatic feeder Function Codes Using function codesFunction code summary Endorser FootswitchOperation ScanningPatch Reader Super12 Document PrinterDescription CodeFunction Code Name F17 F18 F19 F20 F21 F22 F23 F34 F37 F38 F39 Code Function Code Name Enter F58 F59 F60 F62 F63 F64 F65 F66 F70 F71 F72 F73 F74 F75 F91 F92 F93 F94 F95 F96 F97 F98 F99 Cleaning tasks Cleaning materials Replacement parts MaintenanceCleaning the imaging guides Daily maintenance proceduresSeptember Roller cover Release lever Feed roller Separator roller Cleaning the feeder module and separator roller Cleaning the separator roller Cleaning the paper path Vacuuming inside the scanner September September Cleaning the cabinet Weekly maintenance proceduresCleaning the exposure lamp housings Cleaning the air filter Monthly maintenance proceduresReplacing the air filter Replacement proceduresReplacing the exposure lamps September Replacing the imaging guides Replacing the feeder module Replacing the feeder module and separator rollerReplacing the separator roller Ordering replacement parts Ordering cleaning materials Operator Messages Description/Action Required Operator message listingCode Operator Message Displayed Code Code Code E281 E282 E285 E286 E291 E293 E294 E295 E296 E297 E298 Code Various messages Probable Cause TroubleshootingTrouble and remedy chart TroubleTrouble Document path Clearing the document pathClearing documents Feeder/horizontal transport area Imaging guide area Lower roller assembly area Vertical transport area Upper turn area Document exit area Accessories Imaging Station Lamps Supply Catalog # SuppliesSupply Catalog # All other regions Parts and toolsPart/Tool United States and Canada Order NumberUsing the Bar Code Reader Available Characters in Set Start/Stop Characters Bar code typesCode Type Character SetBar code placement Before you begin Enabling the bar code confirma- tion tone Enabling bar code readingPerforming a bar code test September Select either 1=Transport Off or 2=Transport On Using the Evaluate optionStatic bar code evaluation Select 1=EVALUATEUsing the Imaging Station Cutting line 12.5 mm Dynamic bar code evaluation Evaluating test results Dimensional Fields Pass or FailGrade Field Pass 31 to Fail Reflectance Fields Grades a through FCause Problem TypeCommon Causes of Low Bar Code Ratings Field Using the %KODAK option Using the Display optionUsing the %NORM option September Using the check feeder Using the Check Feeder / Check StackerClearing jams in the check feeder Cleaning the check feeder Using the check stacker Die styles Using the EndorserBefore you begin Changing the die drum Endorser Locking lever Latch Endorser rotates to the right Die Spring clip Pry off at this edge Changing the ink roller Setting the date and code number Enabling Endorser Changing the print position Selecting the Endorser modeUsing the Footswitch Footswitch Pressed Action Enabling the confirmation tone Footswitch Pressed actionsFootswitch Released Action Footswitch Released actionsFootswitch Pressed Definition Patch types Using the Patch ReaderPatch code placement Positioning the Patch Reader Sensor Linked modes Appendix a Basic ConceptsModes Image addresses ∙ Enter Using the Next keyAssigning an image address Using Function Code F92 Image address formats Indexing schemesSingle level indexing Two level indexing Image Address Three level indexing Three level offset indexing Level instruction Controlling document level changesDocument A G I N G