IBM N2800e manual Selecting the voltage for your location

Page 61

Appendix C. Setting the thin client voltage for your location

Selecting the voltage for your location:

Note: All N2800e thin clients are preset to the 230V setting when manufactured.

1.Power off the N2800e thin client.

2.Remove the base from the N2800e thin client.

3. Locate the voltage selector switch

.

4.Use a pen, or similar object, to slide the switch to the correct setting for your location (see Voltage selection in Table 11 on page 42).

5.Slide the base back on to the N2800e thin client.

6. Power on the N2800e thin client.

© Copyright IBM Corp. 2000

51

Image 61
Contents N2800e Thin Client Express Reference September Page N2800e Thin Client Express Reference September Page Contents Glossary of abbreviations Safety notices Handling static-sensitive devices About this book How to send your commentsWho should read this book Information available on the World Wide WebViii Understanding your NetVista Thin Client Express Page Learning about the hardware Hardware connectorsStandard hardware Power consumption Monitor specificationsUpgrading hardware features Communication hardwareLearning about the hardware Page Installing options Setting up the hardwareUnpacking your hardware Selecting the voltage for your locationConnecting your hardware Installing the support baseStartup sequence Page Using the Setup Utility to configure the workstation Configuring the N2800e Thin Client ExpressUsing the Configuration Tool to configure the workstation Configuring the N2800e Thin Client Express Page Copyright IBM Corp Click NetVista thin client Page Page Managing your Thin Client Express remotely Page Configuring a workstation for PPP dialer Prerequisites for using PPP dial accessPreparing the workstation for PPP dialer configuration PPP dialer for Thin Client Express workstationsConfiguring initial modem settings for PPP dialer access Starting the PPP dialer Maintaining and reconfiguring PPP dialer parametersLearning about the NC dialer window Troubleshooting PPP dialer problems Using the PPP dialer to access flash imagesAltering the flash image of a workstation Performing a software update on a workstationClick Configure Software Update Server Access Recovering the flash image of a workstationEnabling peer flash recovery on a workstation Recovering the image on the peer-booted workstation Disabling peer flash recovery on a workstation NS/flashbase/x86/kernel.2200 Verifying hardware problems Resolving hardware problemsStartup Visible Symptom What you should do Logic Unit Hardware problem indications Where to find informationVisible hardware failure Mouse Symptom What you should doAudio beep sequences Video memory error Memory errorSymptom What you should do System LED LED indicationsMonitor LED Error codes and text messagesMain memory messages NSB10xxx Battery messages NSB01xxxNon-volatile memory messages Nvram NSB11xxx Audio messages NSB21xxxUSB messages NSB4xxxx Error code Error message What you should doCompactFlash card messages NSB51xxx Ethernet messages NSB62xxxBoot file server messages NSB83xxx Bootp messages NSB72xxxNetwork communication messages NSB8xxxx Tftp messages NSB81xxxClient IP address messages NSB85xxx Gateway messages NSB84xxxSubnet mask messages NSB86xxx IP address messages NSB87xxxReplacing the N2800e Thin Client Express CompactFlash card Appendix A. Replacing hardware partsMemory Replacing parts other than the N2800e CompactFlash cardKeyboards Voltage Selection Plug Receptacle Country Part number Returning hardware parts Removing the logic unit to install parts Appendix B. Hardware maintenance proceduresReassembling the thin client Replacing a CompactFlash card Installing an optional PCI cardExchanging the memory Exchanging the lithium batteryRemoving the power supply Installing the power supply Page Selecting the voltage for your location Page Creating a recovery CompactFlash card Appendix D. Recovering the boot block imageRecovering the flash image BOM file Languages supported Appendix E. Choosing a flash filePage Appendix F. Monitor specifications Page Pin Signal Signal Direction Appendix G. Connector pin informationPin Signal Pin # Direction Description Pin Name FunctionPin # Voltage+5V dc Copyright IBM Corp Product Recycling and Disposal Environmental DesignElectronic Emission Notices TrademarksFederal Communications Commission FCC Statement Industry Canada Compliance Statement Glossary of abbreviations Page Index N2800e understanding How satisfied are you that the information in this book is Readers’ Comments We’d Like to Hear from YouPlease tell us how we can improve this book Readers’ Comments We’d Like to Hear from You Page SA23-2808-00