IBM N2800e manual Trademarks, Electronic Emission Notices

Page 73

Trademarks

The following terms are trademarks of International Business Machines

Corporation in the United States, or other countries, or both:

AS/400

IBM

NetVista

Network Station

S/390

Wake on LAN

Java, and all Java-based trademarks, and logos are trademarks, or registered trademarks of Sun Microsystems, Inc. in the United States, other countries, or both.

Microsoft®, Windows, Windows NT, and the Windows logo are trademarks of

Microsoft Corporation in the United States, other countries, or both.

Electronic Emission Notices

The following Statement applies to this IBM product. The statement for other IBM products intended for use with this product will appear in their accompanying manuals.

Federal Communications Commission (FCC) Statement

Note: This equipment has been tested and found to comply with the limits for a class B digital devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

vReorient or relocate the receiving antenna.

vIncrease the separation between the equipment and receiver.

vConnect the equipment into an outlet on a circuit different from that to which the receiver is connected.

vConsult an IBM authorized dealer or service representative for help.

Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Proper cables and connectors are available from IBM authorized dealers. IBM is not responsible for any radio or television interference caused by using other than recommended cables or connectors or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interferences, and

(2)this device must accept any interferences received, including interference that may cause undesired operation.

Responsible Party:

Notices 63

Image 73
Contents N2800e Thin Client Express Reference September Page N2800e Thin Client Express Reference September Page Contents Glossary of abbreviations Safety notices Handling static-sensitive devices About this book How to send your commentsWho should read this book Information available on the World Wide WebViii Understanding your NetVista Thin Client Express Page Learning about the hardware Hardware connectorsStandard hardware Power consumption Monitor specificationsUpgrading hardware features Communication hardwareLearning about the hardware Page Installing options Setting up the hardwareUnpacking your hardware Selecting the voltage for your locationConnecting your hardware Installing the support baseStartup sequence Page Using the Setup Utility to configure the workstation Configuring the N2800e Thin Client ExpressUsing the Configuration Tool to configure the workstation Configuring the N2800e Thin Client Express Page Copyright IBM Corp Click NetVista thin client Page Page Managing your Thin Client Express remotely Page Configuring a workstation for PPP dialer Prerequisites for using PPP dial accessPreparing the workstation for PPP dialer configuration PPP dialer for Thin Client Express workstationsConfiguring initial modem settings for PPP dialer access Starting the PPP dialer Maintaining and reconfiguring PPP dialer parametersLearning about the NC dialer window Troubleshooting PPP dialer problems Using the PPP dialer to access flash imagesAltering the flash image of a workstation Performing a software update on a workstationClick Configure Software Update Server Access Recovering the flash image of a workstationEnabling peer flash recovery on a workstation Recovering the image on the peer-booted workstation Disabling peer flash recovery on a workstation NS/flashbase/x86/kernel.2200 Verifying hardware problems Resolving hardware problemsStartup Visible Symptom What you should do Logic Unit Hardware problem indications Where to find informationVisible hardware failure Mouse Symptom What you should doAudio beep sequences Video memory error Memory errorSymptom What you should do System LED LED indicationsMonitor LED Error codes and text messagesMain memory messages NSB10xxx Battery messages NSB01xxxNon-volatile memory messages Nvram NSB11xxx Audio messages NSB21xxxUSB messages NSB4xxxx Error code Error message What you should doCompactFlash card messages NSB51xxx Ethernet messages NSB62xxxBoot file server messages NSB83xxx Bootp messages NSB72xxxNetwork communication messages NSB8xxxx Tftp messages NSB81xxxClient IP address messages NSB85xxx Gateway messages NSB84xxxSubnet mask messages NSB86xxx IP address messages NSB87xxxReplacing the N2800e Thin Client Express CompactFlash card Appendix A. Replacing hardware partsMemory Replacing parts other than the N2800e CompactFlash cardKeyboards Voltage Selection Plug Receptacle Country Part number Returning hardware parts Removing the logic unit to install parts Appendix B. Hardware maintenance proceduresReassembling the thin client Replacing a CompactFlash card Installing an optional PCI cardExchanging the memory Exchanging the lithium batteryRemoving the power supply Installing the power supply Page Selecting the voltage for your location Page Creating a recovery CompactFlash card Appendix D. Recovering the boot block imageRecovering the flash image BOM file Languages supported Appendix E. Choosing a flash filePage Appendix F. Monitor specifications Page Pin Signal Signal Direction Appendix G. Connector pin informationPin Signal Pin # Direction Description Pin Name FunctionPin # Voltage+5V dc Copyright IBM Corp Product Recycling and Disposal Environmental DesignElectronic Emission Notices TrademarksFederal Communications Commission FCC Statement Industry Canada Compliance Statement Glossary of abbreviations Page Index N2800e understanding How satisfied are you that the information in this book is Readers’ Comments We’d Like to Hear from YouPlease tell us how we can improve this book Readers’ Comments We’d Like to Hear from You Page SA23-2808-00