Cisco Systems NME-16ES-1G manual Discovery of Candidates and Members Through Routed Ports, Switch

Page 25

Cisco EtherSwitch Service Modules Feature Guide

Information About the Cisco EtherSwitch Service Modules

Switch 9 because automatic discovery does not extend beyond a noncandidate device, which is switch 7

Figure 4

Discovery Through Different Management VLANs with a Layer 3 Cluster Command

 

Switch

 

 

Command

Standby command

 

device

device

VLAN 9

VLAN 16

Device 3 (management VLAN 16)

VLAN 16

Device 4

(management

VLAN 16)

VLAN 62

Device 5 (management VLAN 62)

VLAN trunk 4, 62

Device 7 (management VLAN 4)

VLAN 62

Device 9 (management VLAN 62)

VLAN 9

Device 6 (management VLAN 9)

VLAN 9

Device 8 (management VLAN 9)

VLAN 4

Device 10 (management VLAN 4)

101323

Discovery of Candidates and Members Through Routed Ports

If the cluster command switch has a routed port (RP) configured, it discovers only candidate and cluster member switches in the same VLAN as the routed port.

The Layer 3 cluster command switch in Figure 5 can discover the switches in VLANs 9 and 62 but not the switch in VLAN 4. If the routed port path between the cluster command switch and cluster member switch 7 is lost, connectivity with cluster member switch 7 is maintained because of the redundant path through VLAN 9.

Cisco IOS Release 12.2(25)SEC

25

Image 25
Contents Release Modification GuideContents Hardware Overview Network Modules Hardware Installation GuideSoftware Features and Benefits Performance Features Ease-of-Use and Ease-of-Deployment FeaturesManagement Options Availability Features Manageability FeaturesVlan Features Security Features QoS and CoS Features Monitoring Features Power-over-Ethernet FeaturesCisco StackWise Concepts Overview of Switch StacksSwitch Stack Membership Stack Master Election and Re-Election Stack Member Numbers Switch Stack Bridge ID and Router MAC AddressStack Member Priority Values Stack Protocol Version Compatibility Switch Stack Software Compatibility RecommendationsSwitch Stack Configuration Files Switch Stack Management Connectivity Clustering Concepts Accessing the CLI of a Specific Stack MemberManagement Connectivity to Specific Stack Members Standby Command Device Characteristics Command Device CharacteristicsCluster Compatibility Automatic Discovery of Candidates and Members Candidate and Member CharacteristicsDiscovery of Candidates and Members Through CDP Hops Vlan Discovery of Candidates and Members Through Different VLANs Discovery of Candidates and Members Through Routed Ports SwitchNew out-of-box Discovery of Newly Installed Switches in ClustersHsrp and Standby Cluster Command Switches Other Considerations for Cluster Standby Groups Virtual IP Addresses in ClustersAutomatic Recovery of Cluster Configuration Hostnames in Clusters IP Addresses in ClustersSwitch Clusters and Switch Stacks Passwords in ClustersSwitch Stack Switch Cluster Snmp Community Strings in ClustersSwitch Stack Switch Cluster TACACS+ and Radius in Clusters Availability of Switch-Specific Features in Switch ClustersCisco IOS Release 12.225SEC Using Interface Configuration Mode Boot flash image-name Command or Action PurposeExample Dir flashShow running configuration EnableConfigure terminal Service-module interface slot/port sessionOutput of the show service-module status command Show power inlineShow ip interface brief Control+shift+6Sample Output for the boot flash Command on the Router Sample Output for the dir flash Command on the RouterRouter boot flashc2800-adventerprisek9-mz ExamplesRouter# configure terminal Router# show running config interface gigabitethernet2/0Router# service-module gigabitethernet2/0 session Switch dir flashSwitch# ctrl+shift+6 Switch# show ip interface briefSwitch# show power inline Sample Output for Pressing Ctrl+Shift+6 Followed byDhcp Feature Default SettingSTP Prerequisites Clustering Concepts section on Return Sample Output for Assigning the IP Address and Subnet Mask Sample Output for Entering an Interface NameCommand or Action Purpose Sample Output for Saving the Configuration to NvramRouter# service-module gigabitethernet1/0 reset Router# service-module gigabitethernet1/0 shutdownRouter# service-module gigabitethernet1/0 reload Cisco IOS Release 12.225SEC Restrictions Default Switch Stack ConfigurationAssigning a Stack Member Number Sample Output for the reload slot Command Sample Output for the switch renumber CommandShow switch Switchconfig# switch 6 renumberSample Output for the show switch Command Setting the Stack Member Priority ValueSample Output for the switch priority Command Verifying Information About the Switch StackSwitchconfig# switch 2 priority Switch show switchSwitch# show platform stack-manager all Show switch stack-ports Switchconfig# show switch neighborsRcommand Using the CLI to Manage Switch ClustersShow version Sample Output for the show cluster members Command Sample Output for the rcommand and show version CommandsChoose View Refresh Choose Cluster Add to Cluster or Cluster member PasswordDetailed Steps from the CLI Creating a Cluster Standby GroupRouting-redundancy Cluster standby-group HSRP-group-nameNo switchport Sample Output for the ping tftpserver Command Sample Output for the copy tftp flash Command Sample Output for the show flash CommandSwitch# show flash Switch# copy tftp flashService-module interface slot/port password-reset Flashinit Recovering from a Corrupted Software Image Using XmodemPassword-reset Service-module interface slot/portFlashinit Control+6Sample Output for the copy flash xmodem Command TroubleshootingRouter# copy flash xmodem Router# copy tftp xmodem Sample Output for the copy tftp xmodem CommandRouter# service-module gigabitethernet2/0 password-reset Router# service-module gigabitethernet1/0 sessionRecovering from a Lost or Forgotten Password Optional loadhelper filesystem/file-url Enable secret password Boot -x -v deviceimagenameRename Copy flashReload Copy running-configuration startup-configurationOptional set Boot Service-module password-reset commandExample Sample Output for the set CommandSet Scenario Action Result Current-stack-member-number Renumber new-stack-member-number Network Configuration Examples Network Demands Suggested Design Methods Cost-Effective Wiring Closet Redundant Gigabit Backbone Cisco SoftPhone Software Gigabit servers POP Technical Assistance Related DocumentsRelated Topic Document Title Description Link