Cisco Systems NME-16ES-1G manual Cluster member, Password

Page 61

Cisco EtherSwitch Service Modules Feature Guide

How to Configure a Switch Cluster

DETAILED STEPS FROM THE NETWORK ASSISTANT APPLICATION

Step 1

Step 2 Step 3

Step 4

Step 5

Command or Action

Purpose

 

 

Close the Add to Cluster window.

Closes the Add to Cluster window to view an updated list of

 

cluster members.

 

 

Choose View > Refresh.

Displays an updated list of cluster members.

 

 

Choose Cluster > Add to Cluster.

Allows you to select a candidate service module from the

 

cluster list.

 

When you are at the Cluster > Add to Cluster window,

 

click Add, and click OK. To add more than one

 

candidate service module, press Ctrl, and make your

 

choices, or press Shift, and choose the first and last

 

service module in a range.

 

or

 

Display the Topology view, right-click a

 

candidate-service module icon, and choose Add to

 

Cluster. In the Topology view, candidate service

 

modules are cyan, and cluster member service modules

 

are green. To add more than one candidate service

 

module, press Ctrl, and left-click the candidates that

 

you want to add.

 

 

cluster member

Adds members to the cluster.

 

The example shows how to add a switch with MAC

Example:

address 00E0.1E00.3333 to the cluster. This switch

Switch(config)# cluster member mac-address

does not have a password. The cluster command switch

00E0.1E00.3333

selects the next available member number and assigns

 

it to the switch that is joining the cluster.

 

 

password

Allows you to enter a password if the candidate service

 

module has a password.

Example:

The example shows how to add a switch as member 2

Switch(config)# cluster member 2 mac-address

with MAC address 00E0.1E00.2222 and the password

00E0.1E00.2222 password key vlan 3

key to a cluster. The cluster command switch adds the

 

candidate to the cluster through VLAN 3.

 

 

Cisco IOS Release 12.2(25)SEC

61

Image 61
Contents Release Modification GuideContents Hardware Overview Network Modules Hardware Installation GuideSoftware Features and Benefits Performance Features Ease-of-Use and Ease-of-Deployment FeaturesManagement Options Availability Features Manageability FeaturesVlan Features Security Features QoS and CoS Features Monitoring Features Power-over-Ethernet FeaturesCisco StackWise Concepts Overview of Switch StacksSwitch Stack Membership Stack Master Election and Re-Election Stack Member Numbers Switch Stack Bridge ID and Router MAC AddressStack Member Priority Values Stack Protocol Version Compatibility Switch Stack Software Compatibility RecommendationsSwitch Stack Configuration Files Switch Stack Management Connectivity Clustering Concepts Accessing the CLI of a Specific Stack MemberManagement Connectivity to Specific Stack Members Standby Command Device Characteristics Command Device CharacteristicsCluster Compatibility Automatic Discovery of Candidates and Members Candidate and Member CharacteristicsDiscovery of Candidates and Members Through CDP Hops Vlan Discovery of Candidates and Members Through Different VLANs Discovery of Candidates and Members Through Routed Ports SwitchNew out-of-box Discovery of Newly Installed Switches in ClustersHsrp and Standby Cluster Command Switches Other Considerations for Cluster Standby Groups Virtual IP Addresses in ClustersAutomatic Recovery of Cluster Configuration Hostnames in Clusters IP Addresses in ClustersSwitch Clusters and Switch Stacks Passwords in ClustersSwitch Stack Switch Cluster Snmp Community Strings in ClustersSwitch Stack Switch Cluster TACACS+ and Radius in Clusters Availability of Switch-Specific Features in Switch ClustersCisco IOS Release 12.225SEC Using Interface Configuration Mode Boot flash image-name Command or Action PurposeExample Dir flashShow running configuration EnableConfigure terminal Service-module interface slot/port sessionOutput of the show service-module status command Show power inlineShow ip interface brief Control+shift+6Sample Output for the boot flash Command on the Router Sample Output for the dir flash Command on the RouterRouter boot flashc2800-adventerprisek9-mz ExamplesRouter# configure terminal Router# show running config interface gigabitethernet2/0Router# service-module gigabitethernet2/0 session Switch dir flashSwitch# ctrl+shift+6 Switch# show ip interface briefSwitch# show power inline Sample Output for Pressing Ctrl+Shift+6 Followed byDhcp Feature Default SettingSTP Prerequisites Clustering Concepts section on Return Sample Output for Assigning the IP Address and Subnet Mask Sample Output for Entering an Interface NameCommand or Action Purpose Sample Output for Saving the Configuration to NvramRouter# service-module gigabitethernet1/0 reset Router# service-module gigabitethernet1/0 shutdownRouter# service-module gigabitethernet1/0 reload Cisco IOS Release 12.225SEC Restrictions Default Switch Stack ConfigurationAssigning a Stack Member Number Sample Output for the reload slot Command Sample Output for the switch renumber CommandShow switch Switchconfig# switch 6 renumberSample Output for the show switch Command Setting the Stack Member Priority ValueSample Output for the switch priority Command Verifying Information About the Switch StackSwitchconfig# switch 2 priority Switch show switchSwitch# show platform stack-manager all Show switch stack-ports Switchconfig# show switch neighborsRcommand Using the CLI to Manage Switch ClustersShow version Sample Output for the show cluster members Command Sample Output for the rcommand and show version CommandsChoose View Refresh Choose Cluster Add to Cluster or Cluster member PasswordDetailed Steps from the CLI Creating a Cluster Standby GroupRouting-redundancy Cluster standby-group HSRP-group-nameNo switchport Sample Output for the ping tftpserver Command Sample Output for the copy tftp flash Command Sample Output for the show flash CommandSwitch# show flash Switch# copy tftp flashService-module interface slot/port password-reset Flashinit Recovering from a Corrupted Software Image Using XmodemPassword-reset Service-module interface slot/portFlashinit Control+6Sample Output for the copy flash xmodem Command TroubleshootingRouter# copy flash xmodem Router# copy tftp xmodem Sample Output for the copy tftp xmodem CommandRouter# service-module gigabitethernet2/0 password-reset Router# service-module gigabitethernet1/0 sessionRecovering from a Lost or Forgotten Password Optional loadhelper filesystem/file-url Enable secret password Boot -x -v deviceimagenameRename Copy flashReload Copy running-configuration startup-configurationOptional set Boot Service-module password-reset commandExample Sample Output for the set CommandSet Scenario Action Result Current-stack-member-number Renumber new-stack-member-number Network Configuration Examples Network Demands Suggested Design Methods Cost-Effective Wiring Closet Redundant Gigabit Backbone Cisco SoftPhone Software Gigabit servers POP Technical Assistance Related DocumentsRelated Topic Document Title Description Link