Cisco Systems NME-16ES-1G manual Troubleshooting, Sample Output for the copy flash xmodem Command

Page 69

Cisco EtherSwitch Service Modules Feature Guide

Troubleshooting the Cisco EtherSwitch Service Module Software

	Command or Action	Purpose
Step 8
Step 8	dir flash:	Displays a list of all files and directories in flash memory on
		the service module.
	Example:
	switch> dir flash:
Step 9
Step 9	boot flash: image	Boots the Cisco EtherSwitch service module image if all
		files and directories are in flash memory on the service
	Example:	module.
	Example:
	switch> boot flash:c3825-i5-mz.050404

Troubleshooting

If the downloaded image (files and directories) are not in flash memory on the Cisco EtherSwitch service module, repeat Step 1 through Step 6. If the procedure fails again, ensure that your TFTP connection is up and that your TFTP session is open when you download the image.

Examples

This section provides the following examples:

•Sample Output for the copy flash: xmodem Command, page 69

•Sample Output for the copy tftp: xmodem: Command, page 70

•Sample Output for the service-module session Command on the Cisco EtherSwitch Service Module, page 71

•Sample Output for the dir flash: Command on the Cisco EtherSwitch Service Module, page 71

•Sample Output for the service-modulepassword-reset Command on the Cisco EtherSwitch Service Module, page 71

•Sample Output for the flash_init Command on the Cisco EtherSwitch Service Module, page 72

Sample Output for the copy flash: xmodem Command

The following example shows what appears when you enter the copy flash: xmodem command:

Router# copy flash: xmodem

**** WARNING ****

x/ymodem is a slow transfer protocol limited to the current speed settings of the auxiliary/console ports. The use of the auxiliary port for this download is strongly recommended.

During the course of the download no exec input/output will be available.

---- ******* ----

Proceed? [confirm]

You are prompted for the source filename and destination filename:

Source filename [loader_bs.img]?

Destination filename [loader_bs.img]?

You are prompted for the Cisco EtherSwitch service module slot number:

Service Module slot number? [1]:

Cisco IOS Release 12.2(25)SEC

69

Image 69

Contents Release Modification GuideContents Hardware Overview Network Modules Hardware Installation GuideSoftware Features and Benefits Performance Features Ease-of-Use and Ease-of-Deployment FeaturesManagement Options Availability Features Manageability FeaturesVlan Features Security Features QoS and CoS Features Monitoring Features Power-over-Ethernet FeaturesCisco StackWise Concepts Overview of Switch StacksSwitch Stack Membership Stack Master Election and Re-Election Stack Member Numbers Switch Stack Bridge ID and Router MAC AddressStack Member Priority Values Stack Protocol Version Compatibility Switch Stack Software Compatibility RecommendationsSwitch Stack Configuration Files Switch Stack Management Connectivity Accessing the CLI of a Specific Stack Member Clustering ConceptsManagement Connectivity to Specific Stack Members Command Device Characteristics Standby Command Device CharacteristicsCluster Compatibility Candidate and Member Characteristics Automatic Discovery of Candidates and MembersDiscovery of Candidates and Members Through CDP Hops Vlan Discovery of Candidates and Members Through Different VLANs Discovery of Candidates and Members Through Routed Ports SwitchNew out-of-box Discovery of Newly Installed Switches in ClustersHsrp and Standby Cluster Command Switches Other Considerations for Cluster Standby Groups Virtual IP Addresses in ClustersAutomatic Recovery of Cluster Configuration Hostnames in Clusters IP Addresses in ClustersSwitch Clusters and Switch Stacks Passwords in ClustersSwitch Stack Switch Cluster Snmp Community Strings in ClustersSwitch Stack Switch Cluster TACACS+ and Radius in Clusters Availability of Switch-Specific Features in Switch ClustersCisco IOS Release 12.225SEC Using Interface Configuration Mode Boot flash image-name Command or Action PurposeExample Dir flashShow running configuration EnableConfigure terminal Service-module interface slot/port sessionOutput of the show service-module status command Show power inlineShow ip interface brief Control+shift+6Sample Output for the boot flash Command on the Router Sample Output for the dir flash Command on the RouterRouter boot flashc2800-adventerprisek9-mz ExamplesRouter# configure terminal Router# show running config interface gigabitethernet2/0Router# service-module gigabitethernet2/0 session Switch dir flashSwitch# ctrl+shift+6 Switch# show ip interface briefSwitch# show power inline Sample Output for Pressing Ctrl+Shift+6 Followed byDhcp Feature Default SettingSTP Prerequisites Clustering Concepts section on Return Sample Output for Assigning the IP Address and Subnet Mask Sample Output for Entering an Interface NameCommand or Action Purpose Sample Output for Saving the Configuration to NvramRouter# service-module gigabitethernet1/0 shutdown Router# service-module gigabitethernet1/0 resetRouter# service-module gigabitethernet1/0 reload Cisco IOS Release 12.225SEC Restrictions Default Switch Stack ConfigurationAssigning a Stack Member Number Sample Output for the reload slot Command Sample Output for the switch renumber CommandShow switch Switchconfig# switch 6 renumberSample Output for the show switch Command Setting the Stack Member Priority ValueSample Output for the switch priority Command Verifying Information About the Switch StackSwitchconfig# switch 2 priority Switch show switchSwitch# show platform stack-manager all Show switch stack-ports Switchconfig# show switch neighborsUsing the CLI to Manage Switch Clusters RcommandShow version Sample Output for the show cluster members Command Sample Output for the rcommand and show version CommandsChoose View Refresh Choose Cluster Add to Cluster or Cluster member PasswordDetailed Steps from the CLI Creating a Cluster Standby GroupRouting-redundancy Cluster standby-group HSRP-group-nameNo switchport Sample Output for the ping tftpserver Command Sample Output for the copy tftp flash Command Sample Output for the show flash CommandSwitch# show flash Switch# copy tftp flashService-module interface slot/port password-reset Flashinit Recovering from a Corrupted Software Image Using XmodemPassword-reset Service-module interface slot/portFlashinit Control+6Troubleshooting Sample Output for the copy flash xmodem CommandRouter# copy flash xmodem Router# copy tftp xmodem Sample Output for the copy tftp xmodem CommandRouter# service-module gigabitethernet2/0 password-reset Router# service-module gigabitethernet1/0 sessionRecovering from a Lost or Forgotten Password Optional loadhelper filesystem/file-url Enable secret password Boot -x -v deviceimagenameRename Copy flashReload Copy running-configuration startup-configurationOptional set Boot Service-module password-reset commandSample Output for the set Command ExampleSet Scenario Action Result Current-stack-member-number Renumber new-stack-member-number Network Configuration Examples Network Demands Suggested Design Methods Cost-Effective Wiring Closet Redundant Gigabit Backbone Cisco SoftPhone Software Gigabit servers POP Technical Assistance Related DocumentsRelated Topic Document Title Description Link