Cisco Systems NME-16ES-1G manual Examples, Sample Output for the dir flash Command on the Router

Page 39

Cisco EtherSwitch Service Modules Feature Guide

How to Configure the Cisco EtherSwitch Service Module

Examples

This section provides the following examples:

•Sample Output for the dir flash: Command on the Router, page 39

•Sample Output for the boot flash: Command on the Router, page 39

•Sample Output for the show running config Command on the Router, page 40

•Sample Output for Configuring the Cisco EtherSwitch Service Module Interface on the Router, page 40

•Sample Output for the service-module Command on the Cisco EtherSwitch Service Module, page 40

•Sample Output for the dir flash: Command on the Cisco EtherSwitch Service Module, page 40

•Sample Output for the boot flash: Command on the Cisco EtherSwitch Service Module, page 40

•Sample Output for the show ip interface brief Command on the Cisco EtherSwitch Service Module, page 41

•Sample Output for Pressing <Ctrl+Shift+6> Followed by x, page 41

•Sample Output for the show power inline Command on the Cisco EtherSwitch service module, page 41

Sample Output for the dir flash: Command on the Router

The following example shows what appears when you enter the dir flash: command:

Router> dir flash:

Directory of flash:/

program load complete, entry point: 0x8000f000, size: 0xc0c0

Initializing ATA monitor library.......

Directory of flash:

2 29823132 -rw- c2800-adventerprisek9-mz

Sample Output for the boot flash: Command on the Router

The following example shows what appears when you enter the boot flash: command:

Router> boot flash:c2800-adventerprisek9-mz

program load complete, entry point: 0x8000f000, size: 0xc0c0

Initializing ATA monitor library.......

program load complete, entry point: 0x8000f000, size: 0x1c70efc Self decompressing the image :

##########################################################################################

########################################## [OK]

...

After the router completes the boot process, you will be prompted to enter the initial configuration dialog as in the following example. Enter no.

Would you like to enter the initial configuration dialog? [yes/no]: no

Press RETURN to get started!

Press Enter. You will be at the router prompt.

Cisco IOS Release 12.2(25)SEC

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Release Modification GuideContents Hardware Overview Network Modules Hardware Installation GuideSoftware Features and Benefits Performance Features Ease-of-Use and Ease-of-Deployment FeaturesManagement Options Availability Features Manageability FeaturesVlan Features Security Features QoS and CoS Features Monitoring Features Power-over-Ethernet FeaturesCisco StackWise Concepts Overview of Switch StacksSwitch Stack Membership Stack Master Election and Re-Election Stack Member Numbers Switch Stack Bridge ID and Router MAC AddressStack Member Priority Values Stack Protocol Version Compatibility Switch Stack Software Compatibility RecommendationsSwitch Stack Configuration Files Switch Stack Management Connectivity Accessing the CLI of a Specific Stack Member Clustering ConceptsManagement Connectivity to Specific Stack Members Command Device Characteristics Standby Command Device CharacteristicsCluster Compatibility Candidate and Member Characteristics Automatic Discovery of Candidates and MembersDiscovery of Candidates and Members Through CDP Hops Vlan Discovery of Candidates and Members Through Different VLANs Discovery of Candidates and Members Through Routed Ports SwitchNew out-of-box Discovery of Newly Installed Switches in ClustersHsrp and Standby Cluster Command Switches Other Considerations for Cluster Standby Groups Virtual IP Addresses in ClustersAutomatic Recovery of Cluster Configuration Hostnames in Clusters IP Addresses in ClustersSnmp Community Strings in Clusters Passwords in ClustersSwitch Clusters and Switch Stacks Switch Stack Switch ClusterSwitch Stack Switch Cluster TACACS+ and Radius in Clusters Availability of Switch-Specific Features in Switch ClustersCisco IOS Release 12.225SEC Using Interface Configuration Mode Dir flash Command or Action PurposeBoot flash image-name ExampleService-module interface slot/port session EnableShow running configuration Configure terminalControl+shift+6 Show power inlineOutput of the show service-module status command Show ip interface briefExamples Sample Output for the dir flash Command on the RouterSample Output for the boot flash Command on the Router Router boot flashc2800-adventerprisek9-mzSwitch dir flash Router# show running config interface gigabitethernet2/0Router# configure terminal Router# service-module gigabitethernet2/0 sessionSample Output for Pressing Ctrl+Shift+6 Followed by Switch# show ip interface briefSwitch# ctrl+shift+6 Switch# show power inlineDhcp Feature Default SettingSTP Prerequisites Clustering Concepts section on Return Sample Output for Assigning the IP Address and Subnet Mask Sample Output for Entering an Interface NameCommand or Action Purpose Sample Output for Saving the Configuration to NvramRouter# service-module gigabitethernet1/0 shutdown Router# service-module gigabitethernet1/0 resetRouter# service-module gigabitethernet1/0 reload Cisco IOS Release 12.225SEC Restrictions Default Switch Stack ConfigurationAssigning a Stack Member Number Switchconfig# switch 6 renumber Sample Output for the switch renumber CommandSample Output for the reload slot Command Show switchSample Output for the show switch Command Setting the Stack Member Priority ValueSwitch show switch Verifying Information About the Switch StackSample Output for the switch priority Command Switchconfig# switch 2 prioritySwitch# show platform stack-manager all Show switch stack-ports Switchconfig# show switch neighborsUsing the CLI to Manage Switch Clusters RcommandShow version Sample Output for the show cluster members Command Sample Output for the rcommand and show version CommandsChoose View Refresh Choose Cluster Add to Cluster or Cluster member PasswordDetailed Steps from the CLI Creating a Cluster Standby GroupRouting-redundancy Cluster standby-group HSRP-group-nameNo switchport Sample Output for the ping tftpserver Command Switch# copy tftp flash Sample Output for the show flash CommandSample Output for the copy tftp flash Command Switch# show flashService-module interface slot/port password-reset Flashinit Recovering from a Corrupted Software Image Using XmodemControl+6 Service-module interface slot/portPassword-reset FlashinitTroubleshooting Sample Output for the copy flash xmodem CommandRouter# copy flash xmodem Router# copy tftp xmodem Sample Output for the copy tftp xmodem CommandRouter# service-module gigabitethernet2/0 password-reset Router# service-module gigabitethernet1/0 sessionRecovering from a Lost or Forgotten Password Optional loadhelper filesystem/file-url Copy flash Boot -x -v deviceimagenameEnable secret password RenameReload Copy running-configuration startup-configurationOptional set Boot Service-module password-reset commandSample Output for the set Command ExampleSet Scenario Action Result Current-stack-member-number Renumber new-stack-member-number Network Configuration Examples Network Demands Suggested Design Methods Cost-Effective Wiring Closet Redundant Gigabit Backbone Cisco SoftPhone Software Gigabit servers POP Description Link Related DocumentsTechnical Assistance Related Topic Document Title
Top Page Image Contents