Cisco Systems NME-16ES-1G manual Assigning a Stack Member Number, Command or Action Purpose

Page 52

Cisco EtherSwitch Service Modules Feature Guide

How to Configure the Cisco EtherSwitch Service Module in a Switch Stack

Removing powered-up stack members from the stack causes the Cisco EtherSwitch service module stack to divide (partition) into two or more switch stacks, each with the same configuration. This can cause an IP address configuration conflict in your network. If you want the switch stacks to remain separate, change the IP address or addresses of the newly created switch stacks. If you did not intend to partition the switch stack, follow these steps:

a.Power down the newly created switch stacks.

b.Reconnect them to the original switch stack through their Cisco StackWise ports.

c.Power up the switches.

Note A Cisco EtherSwitch service module does not have an on/off switch. To turn off the Cisco EtherSwitch service module, issue the service gigabitethernet1/0 shutdown command from the router.

Assigning a Stack Member Number

This section describes how to assign a stack member number to the Cisco EtherSwitch service module in a switch stack.

SUMMARY STEPS

1.configure terminal

2.switch current-stack-member-number renumber new-stack-member-number

3.end

4.reload slot stack-member-number

5.show switch

DETAILED STEPS

 

Command or Action

Purpose

Step 1

 

 

configure terminal

Enters global configuration mode.

 

Example:

 

 

Switch# configure terminal

 

Step 2

 

 

switch current-stack-member-number renumber

Specifies the current stack member number and the new

 

new-stack-member-number

stack member number for the stack member.

 

Example:

The stack member number range is 1 to 9.

 

You can display the current stack member number by

 

Switch (config)# switch 1 renumber 2

 

using the show switch user EXEC command.

 

 

Step 3

 

 

end

Returns you to privileged EXEC mode.

 

Example:

 

 

Switch (config)# end

 

 

 

 

Cisco IOS Release 12.2(25)SEC

52

Image 52
Contents Guide Release ModificationContents Network Modules Hardware Installation Guide Hardware OverviewSoftware Features and Benefits Ease-of-Use and Ease-of-Deployment Features Performance FeaturesManagement Options Manageability Features Availability FeaturesVlan Features Security Features QoS and CoS Features Power-over-Ethernet Features Monitoring FeaturesOverview of Switch Stacks Cisco StackWise ConceptsSwitch Stack Membership Stack Master Election and Re-Election Switch Stack Bridge ID and Router MAC Address Stack Member NumbersStack Member Priority Values Switch Stack Software Compatibility Recommendations Stack Protocol Version CompatibilitySwitch Stack Configuration Files Switch Stack Management Connectivity Clustering Concepts Accessing the CLI of a Specific Stack MemberManagement Connectivity to Specific Stack Members Standby Command Device Characteristics Command Device CharacteristicsCluster Compatibility Automatic Discovery of Candidates and Members Candidate and Member CharacteristicsDiscovery of Candidates and Members Through CDP Hops Vlan Discovery of Candidates and Members Through Different VLANs Switch Discovery of Candidates and Members Through Routed PortsDiscovery of Newly Installed Switches in Clusters New out-of-boxHsrp and Standby Cluster Command Switches Virtual IP Addresses in Clusters Other Considerations for Cluster Standby GroupsAutomatic Recovery of Cluster Configuration IP Addresses in Clusters Hostnames in ClustersPasswords in Clusters Switch Clusters and Switch StacksSwitch Stack Switch Cluster Snmp Community Strings in ClustersSwitch Stack Switch Cluster Availability of Switch-Specific Features in Switch Clusters TACACS+ and Radius in ClustersCisco IOS Release 12.225SEC Using Interface Configuration Mode Command or Action Purpose Boot flash image-nameExample Dir flashEnable Show running configurationConfigure terminal Service-module interface slot/port sessionShow power inline Output of the show service-module status commandShow ip interface brief Control+shift+6Sample Output for the dir flash Command on the Router Sample Output for the boot flash Command on the RouterRouter boot flashc2800-adventerprisek9-mz ExamplesRouter# show running config interface gigabitethernet2/0 Router# configure terminalRouter# service-module gigabitethernet2/0 session Switch dir flashSwitch# show ip interface brief Switch# ctrl+shift+6Switch# show power inline Sample Output for Pressing Ctrl+Shift+6 Followed byFeature Default Setting DhcpSTP Prerequisites Clustering Concepts section on Return Sample Output for Entering an Interface Name Sample Output for Assigning the IP Address and Subnet MaskSample Output for Saving the Configuration to Nvram Command or Action PurposeRouter# service-module gigabitethernet1/0 reset Router# service-module gigabitethernet1/0 shutdownRouter# service-module gigabitethernet1/0 reload Cisco IOS Release 12.225SEC Default Switch Stack Configuration RestrictionsAssigning a Stack Member Number Sample Output for the switch renumber Command Sample Output for the reload slot CommandShow switch Switchconfig# switch 6 renumberSetting the Stack Member Priority Value Sample Output for the show switch CommandVerifying Information About the Switch Stack Sample Output for the switch priority CommandSwitchconfig# switch 2 priority Switch show switchSwitch# show platform stack-manager all Switchconfig# show switch neighbors Show switch stack-portsRcommand Using the CLI to Manage Switch ClustersShow version Sample Output for the rcommand and show version Commands Sample Output for the show cluster members CommandChoose View Refresh Choose Cluster Add to Cluster or Password Cluster memberCreating a Cluster Standby Group Detailed Steps from the CLICluster standby-group HSRP-group-name Routing-redundancyNo switchport Sample Output for the ping tftpserver Command Sample Output for the show flash Command Sample Output for the copy tftp flash CommandSwitch# show flash Switch# copy tftp flashRecovering from a Corrupted Software Image Using Xmodem Service-module interface slot/port password-reset FlashinitService-module interface slot/port Password-resetFlashinit Control+6Sample Output for the copy flash xmodem Command TroubleshootingRouter# copy flash xmodem Sample Output for the copy tftp xmodem Command Router# copy tftp xmodemRouter# service-module gigabitethernet1/0 session Router# service-module gigabitethernet2/0 password-resetRecovering from a Lost or Forgotten Password Optional loadhelper filesystem/file-url Boot -x -v deviceimagename Enable secret passwordRename Copy flashCopy running-configuration startup-configuration ReloadOptional set Service-module password-reset command BootExample Sample Output for the set CommandSet Scenario Action Result Current-stack-member-number Renumber new-stack-member-number Network Configuration Examples Network Demands Suggested Design Methods Cost-Effective Wiring Closet Redundant Gigabit Backbone Cisco SoftPhone Software Gigabit servers POP Related Documents Technical AssistanceRelated Topic Document Title Description Link