Cisco Systems NME-16ES-1G manual Power-over-Ethernet Features, Monitoring Features

Page 11

Cisco EtherSwitch Service Modules Feature Guide

Information About the Cisco EtherSwitch Service Modules

Egress queues and scheduling

Four egress queues per port.

WTD as the congestion-avoidance mechanism for managing the queue lengths and providing drop precedences for different traffic classifications.

SRR as the scheduling service for specifying the rate at which packets are dequeued to the egress interface (shaping or sharing is supported on egress queues). Shaped egress queues are guaranteed but limited to using a share of port bandwidth. Shared egress queues are also guaranteed a configured share of bandwidth, but can use more than the guarantee if other queues become empty and do not use their share of the bandwidth.

Power-over-Ethernet Features

Ability to provide power to connected Cisco pre-standard and IEEE 802.3af-compliant powered devices from all 10/100-Mbps Ethernet ports if the Cisco EtherSwitch service module detects that there is no power up the circuit

A 24-port PoE Cisco EtherSwitch service module can provide up to 15.4 W of power on each 10/100-Mbps port. A 48-port PoE Cisco EtherSwitch service module can provide up to 15.4 W of power to any 23 of the 48 10/100-Mbps ports. Any combination of ports can provide up to an average of 7.5 W of power at the same time, depending on the power supply capacity in the router chassis.

Note Total power provided is up to the limit of the platform power supply. PoE requires using the AC+IP power supply (not the default power supply) that was shipped with your router. For information about PoE power requirements, access the Cisco.com web page. Click the Products and Solutions link. From the pull-down menu, click Routers and Routing Systems. Click the router platform on which you will install the Cisco EtherSwitch service module.

Monitoring Features

Cisco EtherSwitch service module LEDs that provide port-, service module-, and stack-level status

MAC address notification traps and RADIUS accounting for tracking users on a network by storing the MAC addresses that the Cisco EtherSwitch service module has learned or removed

Switched Port Analyzer (SPAN) and Remote SPAN (RSPAN) for traffic monitoring on any port or

VLAN

SPAN and RSPAN support of Intrusion Detection Systems (IDS) to monitor, repel, and report network security violations

Four groups (history, statistics, alarms, and events) of embedded RMON agents for network monitoring and traffic analysis

Syslog facility for logging system messages about authentication or authorization errors, resource issues, and timeout events

Layer 2 traceroute to identify the physical path that a packet takes from a source device to a destination device

Time Domain Reflectometer (TDR) to diagnose and resolve cabling problems on copper Ethernet 10/100/1000-Mbps ports

Cisco IOS Release 12.2(25)SEC

11

Image 11
Contents Release Modification GuideContents Hardware Overview Network Modules Hardware Installation GuideSoftware Features and Benefits Performance Features Ease-of-Use and Ease-of-Deployment FeaturesManagement Options Availability Features Manageability FeaturesVlan Features Security Features QoS and CoS Features Monitoring Features Power-over-Ethernet FeaturesCisco StackWise Concepts Overview of Switch StacksSwitch Stack Membership Stack Master Election and Re-Election Stack Member Numbers Switch Stack Bridge ID and Router MAC AddressStack Member Priority Values Stack Protocol Version Compatibility Switch Stack Software Compatibility RecommendationsSwitch Stack Configuration Files Switch Stack Management Connectivity Management Connectivity to Specific Stack Members Accessing the CLI of a Specific Stack MemberClustering Concepts Cluster Compatibility Command Device CharacteristicsStandby Command Device Characteristics Discovery of Candidates and Members Through CDP Hops Candidate and Member CharacteristicsAutomatic Discovery of Candidates and Members Vlan Discovery of Candidates and Members Through Different VLANs Discovery of Candidates and Members Through Routed Ports SwitchNew out-of-box Discovery of Newly Installed Switches in ClustersHsrp and Standby Cluster Command Switches Other Considerations for Cluster Standby Groups Virtual IP Addresses in ClustersAutomatic Recovery of Cluster Configuration Hostnames in Clusters IP Addresses in ClustersSnmp Community Strings in Clusters Passwords in ClustersSwitch Clusters and Switch Stacks Switch Stack Switch ClusterSwitch Stack Switch Cluster TACACS+ and Radius in Clusters Availability of Switch-Specific Features in Switch ClustersCisco IOS Release 12.225SEC Using Interface Configuration Mode Dir flash Command or Action PurposeBoot flash image-name ExampleService-module interface slot/port session EnableShow running configuration Configure terminalControl+shift+6 Show power inlineOutput of the show service-module status command Show ip interface briefExamples Sample Output for the dir flash Command on the RouterSample Output for the boot flash Command on the Router Router boot flashc2800-adventerprisek9-mzSwitch dir flash Router# show running config interface gigabitethernet2/0Router# configure terminal Router# service-module gigabitethernet2/0 sessionSample Output for Pressing Ctrl+Shift+6 Followed by Switch# show ip interface briefSwitch# ctrl+shift+6 Switch# show power inlineDhcp Feature Default SettingSTP Prerequisites Clustering Concepts section on Return Sample Output for Assigning the IP Address and Subnet Mask Sample Output for Entering an Interface NameCommand or Action Purpose Sample Output for Saving the Configuration to NvramRouter# service-module gigabitethernet1/0 reload Router# service-module gigabitethernet1/0 shutdownRouter# service-module gigabitethernet1/0 reset Cisco IOS Release 12.225SEC Restrictions Default Switch Stack ConfigurationAssigning a Stack Member Number Switchconfig# switch 6 renumber Sample Output for the switch renumber CommandSample Output for the reload slot Command Show switchSample Output for the show switch Command Setting the Stack Member Priority ValueSwitch show switch Verifying Information About the Switch StackSample Output for the switch priority Command Switchconfig# switch 2 prioritySwitch# show platform stack-manager all Show switch stack-ports Switchconfig# show switch neighborsShow version Using the CLI to Manage Switch ClustersRcommand Sample Output for the show cluster members Command Sample Output for the rcommand and show version CommandsChoose View Refresh Choose Cluster Add to Cluster or Cluster member PasswordDetailed Steps from the CLI Creating a Cluster Standby GroupRouting-redundancy Cluster standby-group HSRP-group-nameNo switchport Sample Output for the ping tftpserver Command Switch# copy tftp flash Sample Output for the show flash CommandSample Output for the copy tftp flash Command Switch# show flashService-module interface slot/port password-reset Flashinit Recovering from a Corrupted Software Image Using XmodemControl+6 Service-module interface slot/portPassword-reset FlashinitRouter# copy flash xmodem TroubleshootingSample Output for the copy flash xmodem Command Router# copy tftp xmodem Sample Output for the copy tftp xmodem CommandRouter# service-module gigabitethernet2/0 password-reset Router# service-module gigabitethernet1/0 sessionRecovering from a Lost or Forgotten Password Optional loadhelper filesystem/file-url Copy flash Boot -x -v deviceimagenameEnable secret password RenameReload Copy running-configuration startup-configurationOptional set Boot Service-module password-reset commandSet Sample Output for the set CommandExample Scenario Action Result Current-stack-member-number Renumber new-stack-member-number Network Configuration Examples Network Demands Suggested Design Methods Cost-Effective Wiring Closet Redundant Gigabit Backbone Cisco SoftPhone Software Gigabit servers POP Description Link Related DocumentsTechnical Assistance Related Topic Document Title