Extron electronic PVS 305SA manual Introduction Inventory Overview, cont’d, Items not included

Page 10

Introduction — Inventory Overview, cont’d

b. Items not included

The following items are not included. However, input and display devices are essential parts of the system, and at any installation they may vary depending on their use. This list suggests various devices that may be used.

•Projector (or display device)

•Screen (and mounting hardware)

•Input devices, such as:

DVD/CD/VCR combo player (and cables)

Document camera (and cables)

PC or Mac (with keyboard, mouse, local monitor, VGA cables, RJ-45 network cables, power cords, and, where desired, a P/2 DA2 or DA for PC signal to local monitor)

•Installation hardware needed (may vary per installation):

Bolts for concrete structural ceilings where needed

Toggles (used for screen mounting on dry wall)

S-hooks for hanging the screen

Spare ceiling tiles in case of accidental damage during installation

Electrical box, where installation of a box on the PCM 340 is desired

Safety wire, lag eye bolts, and strain reliefs for installation and securing ceiling speakers

Heat shrink, extension cord c. Optional items

The optional Extron products suggested below can be added to or substituted for items in the standard PoleVault System.

•Optional accessories:

Wall mount speakers (e.g., SI 26) or extra ceiling speakers

MLC 104 IP Plus DV+ controller (includes DVD/VCR IR control)

MLC 104 IP Plus L controller (with lectern faceplate)

MLC 104 IP Plus AAP controller (with AAP opening)

MLC 226 IP controller

Priority Page Sensor Kit

P/2 DA2

•Optional installation hardware:

FCMP (flat ceiling mount)

ACMP (angled ceiling mount)

SMB (surface mount boxes for installing the MLC on a podium or desk)

EWB (external wall boxes to mount devices for a surface raceway system)

MLM-WB+ (lockable metal wall box with flip-down 4U rack space)

•Optional A/V source inputs:

PVT RGB D Plus (RGB Decora mount model, with IR and local monitor output)

PVT CV AAP (composite video architectural adapter plate model)

PVT RGB AAP (RGB architectural adapter plate model)

PVT RGB (RGB rack mount model)

PVT SW RGB (RGB rack mount model with switching capabilities)

PVT CV (composite video rack mount model)

PVT RGB CV (RGB and composite video rack mount model)

•Optional speakers:

SI 3 (Compact Full-Range Surface Mount Speakers)

SI 26X (Two-Way Open Back Ceiling Speakers)

SI 26W (Two-Way-In-Wall Speakers with 6.5" Woofer)

SI 28W (Two-Way-In-Wall Speakers with 8" Woofer)

SI 26CT (Two-Way Ceiling Speakers with 8" Back Can and Transformer)

SI 26 (Two-Way Surface Mount Speakers with 6.5" Woofer)

SI 3C LP ( Full-Range Ceiling Speakers with 4" Low Profile Back Can)

1-8 PoleVault Systems Installation • Introduction — Inventory Overview

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Installation Guide PoleVault SystemsConsignes de Sécurité Français PrecautionsSafety Instructions English Sicherheitsanleitungen DeutschIntroduction PoleVault Systems Installation IntroductionFCC Class B Notice PoleVault System installation and wiring overview Introduction, contdRoom layout Typical classroom installationPoleVault Systems Installation Introduction Planning RoomLocation of the screen and projector Example classroom installationIntroduction Planning, cont’d ADA overhead and side clearance requirementsLocation of source devices Example classroom with four speaker installationLocation of MediaLink Controller and Wall Plates Cabling obstaclesInventory Introduction Inventory OverviewIncluded items PoleVault System Devices and Hardware, cont’d Introduction Inventory Overview, cont’d Optional installation hardwareItems not included Installation tools Outline of installation steps Installation OverviewPoleVault Systems Installation Installation PCM 340 Projector Drop Ceiling Mount Stage One Install the Screen and ProjectorPoleVault Systems Installation Installation Stage Slotted Pipe Supplied with PCMMark screen location Installation Stage One, cont’dInstall projector to verify location 1a Mark the screen location2e Attach the bracket to the projector 2f Slide and lock the projector onto the adjuster plateVerify the image location Horizontal offsetCut the ceiling tile Preliminary safety hardware installation5a Mark structural ceiling for lag eye bolt installation 4b Take measurements with the PCM 340 on the T-frame7a Attach turnbuckles at the corners Finish Projector Drop Ceiling Mount installationSecure the Projector Drop Ceiling Mount to the ceiling 7c Hand tighten the turnbucklesInstall the Screen Install the electrical box if required8a Install Raco box and plaster ring This stage involves installing the devices shown below Stage Two Install the Wall Plates and MLC 104 IP PlusMLC 104 IP Plus MediaLink Controller IR/RS-232 communications cable control cable Installation Stage Two, cont’dCables RS-232 or to an IR emitterMLC 104 IP Plus mud ring Install the mud rings1d Features for mud ring installation 1c Insert the mud ringPull the cables at the input locations Signal Cable Label color2c Pull the cables at each location Install wall plates MLC 104 IP Plus controllerWire stripping lengths Install MediaLink Controller4a Connecting the MLC to the switcher An RS-232 cable or IR emitter cable, as 4c Connect to the LAN using a CAT 5 cableConnect the MLC to the projector with AppropriateConnections made to the MLC 104 IP Plus 4e Secure the MLC 104 IP Plus to the mud ringStage Three Install the FF 120 Ceiling Speakers FF 120 Flat Field Ceiling Speakers2h Attach safety cable Installation Stage Three, cont’dInstall the speaker on the drop ceiling Cut ceiling tileStereo or dual mono output using parallel speaker wiring Terminate the speaker cable for the PVS switcherPole captive screw connector To terminate the cable, strip the end of the cable 0.2 inchPVS 305SA PoleVault Switcher Stage Four Install the PMK 550 and the PVS 305SAThis stage covers installing the devices shown below PMK 550 Pole Mount KitInstall the PMK 550 base plate PoleVault Systems Installation Installation Stage 4Switcher and projector cable overview Installation Stage Four, cont’dPull the cables at the switcher location 2b Gather the cables, pass them down the pipe4a Connect the cables to the switcher Finish installing the Pole Mount kitBControl/power cable from the MLC 104 IP Plus Connect the cables as follows to the PVS 305SA4b Reattach UPB bracket and 4c projector 4d Cable the projectorConfigure the switcher MLS Switcher Configuration program Stage Five Configure the Switcher and the SystemGlobal configurator software Installation Stage Five, cont’d Configure the system Global Configurator3c Check that an image is present, adjust as needed Loosen all pivot screws and adjust the vertical angleTest the system Where installed, if necessary, adjust the sensitivity Final installationAdjust the configuration as necessary 3d Test the MLC configurationAttach the Z bracket to the ceiling tile and the back plate Optional Accessory Installation VoiceLift SystemAlign the arrows on the housing rim and the dome tab Plug VoiceLift cable into PVS 305SAPriority Page Sensor Kit included parts Optional Accessory Installation Priority Page Sensor KitOpen the sensor and loop a wire around the sensor UL-compliant junction box and coverTypical paging system with the PVS 305SA switcher Testing and Adjustment Procedure4 Sensitivity knob adjustment PoleVault Systems Installation Reference Information Reference InformationWall or furniture mountable with included Decora wall plate Lbs 0.1 kgReference Information, cont’d Extron PCMSIS Command/Response Table Ascii Telnet SIS CommandsPVS 305SA specific symbol definitions PoleVault Systems Installation Basic SIS CommandsExtron USA West
Top Page Image Contents