Extron electronic PVS 305SA manual PoleVault System Devices and Hardware, cont’d

Page 9

PoleVault System Devices and Hardware, cont’d

PoleVault System

42-108-03 (or 42-109-03*, or 42-110-03*)

PVS 305SA

PVT CV D	PVT RGB D Plus
PVT CV D White	PVT RGB D White
60-819-33	60-820-13

		FF 120
MLC 104 IP Plus

PVS 305SA

60-986-01

			INPUT SELECTION					PVS 305SA
								POLEVAULT SWITCHER
	1	2	3	4	5	AUDIO LEVEL ADJUST			PAGING
	1	2	3	4	5	INPUT PEAK	MIC	PEAK	PAGING
						INPUT PEAK	MIC	PEAK	SENSOR
	CONFIG					NORMAL		NORMAL
	CONFIG
						SIGNAL	VOICELIFT	SIGNAL	SENSITIVITY
					AUX AUDIO		VOICELIFT		SENSITIVITY
					AUX AUDIO

PVS 305SA

PoleVault Switcher

(1)3-pole connector

(3)5-pole connector

(1)Audio connector, 4-pole

(2)Securing screws

(5) Tie wraps

(1)Power supply

(1)Power cord

VIDEO IN
AUDIO IN
L	R
S	G
IR OUT

PVT CV D

Wallplate

(1)Mud ring

(2)PVT mounting screws

(1)Decora® Faceplate

(2)Faceplate screws

(1)2-pole connector

AUDIO IN

COMPUTER IN

PVT RGB Plus D

Wallplate

or optional PVT RGB D Plus White

60-820-33

AUDIO
IN	OUT
COMPUTER IN
MONITOR OUT
S	G
IR OUT

PVT RGB Plus D

Wallplate

(1)Mud ring

(2)PVT mounting screws

(1)Decora® Faceplate

(2)Faceplate screws

MLC 104 IP Plus White

60-818-03

DISPLAY
ON	OFF	VCR	1
VOLUME		DVD	2
VOLUME
		PC	3
		CONFIG
			4
		MLC 104 IP Plus

MLC 104 IP Plus

MediaLink Controller

(1) Mud ring

(8) Mud ring screws

(8)Replacement screws

(2)Faceplates -

(1)White (on unit)

(1)Black

FF120

42-120-03

FF120 Speakers

(2)Cable clamps - Anchor ring

(2)T-rails

*Part #s 42-109-03 and 42-110-03 contain 3 or 4 PoleVault Wallplates, according to the type ordered.

NIf any items in the PoleVault System boxes are damaged or missing, contact the Extron Technical Hotline (see rear cover for contact numbers).

PoleVault Systems Installation • Introduction — Inventory Overview

1-7

Image 9

Contents PoleVault Systems Installation GuideSafety Instructions English PrecautionsConsignes de Sécurité Français Sicherheitsanleitungen DeutschPoleVault Systems Installation Introduction IntroductionFCC Class B Notice Introduction, contd PoleVault System installation and wiring overviewPoleVault Systems Installation Introduction Planning Typical classroom installationRoom layout Room Introduction Planning, cont’d Example classroom installation Location of the screen and projector ADA overhead and side clearance requirementsLocation of MediaLink Controller and Wall Plates Example classroom with four speaker installationLocation of source devices Cabling obstaclesIntroduction Inventory Overview InventoryIncluded items PoleVault System Devices and Hardware, cont’d Optional installation hardware Introduction Inventory Overview, cont’dItems not included Installation tools Installation Overview Outline of installation stepsPoleVault Systems Installation Installation PoleVault Systems Installation Installation Stage Stage One Install the Screen and ProjectorPCM 340 Projector Drop Ceiling Mount Slotted Pipe Supplied with PCMInstall projector to verify location Installation Stage One, cont’dMark screen location 1a Mark the screen locationVerify the image location 2f Slide and lock the projector onto the adjuster plate2e Attach the bracket to the projector Horizontal offset5a Mark structural ceiling for lag eye bolt installation Preliminary safety hardware installationCut the ceiling tile 4b Take measurements with the PCM 340 on the T-frameSecure the Projector Drop Ceiling Mount to the ceiling Finish Projector Drop Ceiling Mount installation7a Attach turnbuckles at the corners 7c Hand tighten the turnbucklesInstall the electrical box if required Install the Screen8a Install Raco box and plaster ring Stage Two Install the Wall Plates and MLC 104 IP Plus This stage involves installing the devices shown belowMLC 104 IP Plus MediaLink Controller Cables Installation Stage Two, cont’dIR/RS-232 communications cable control cable RS-232 or to an IR emitter1d Features for mud ring installation Install the mud ringsMLC 104 IP Plus mud ring 1c Insert the mud ringSignal Cable Label color Pull the cables at the input locations2c Pull the cables at each location MLC 104 IP Plus controller Install wall platesInstall MediaLink Controller Wire stripping lengths4a Connecting the MLC to the switcher Connect the MLC to the projector with 4c Connect to the LAN using a CAT 5 cableAn RS-232 cable or IR emitter cable, as Appropriate4e Secure the MLC 104 IP Plus to the mud ring Connections made to the MLC 104 IP PlusFF 120 Flat Field Ceiling Speakers Stage Three Install the FF 120 Ceiling SpeakersInstall the speaker on the drop ceiling Installation Stage Three, cont’d2h Attach safety cable Cut ceiling tilePole captive screw connector Terminate the speaker cable for the PVS switcherStereo or dual mono output using parallel speaker wiring To terminate the cable, strip the end of the cable 0.2 inchThis stage covers installing the devices shown below Stage Four Install the PMK 550 and the PVS 305SAPVS 305SA PoleVault Switcher PMK 550 Pole Mount KitPoleVault Systems Installation Installation Stage 4 Install the PMK 550 base platePull the cables at the switcher location Installation Stage Four, cont’dSwitcher and projector cable overview 2b Gather the cables, pass them down the pipeBControl/power cable from the MLC 104 IP Plus Finish installing the Pole Mount kit4a Connect the cables to the switcher Connect the cables as follows to the PVS 305SA4d Cable the projector 4b Reattach UPB bracket and 4c projectorStage Five Configure the Switcher and the System Configure the switcher MLS Switcher Configuration programGlobal configurator software Configure the system Global Configurator Installation Stage Five, cont’dLoosen all pivot screws and adjust the vertical angle 3c Check that an image is present, adjust as neededTest the system Adjust the configuration as necessary Final installationWhere installed, if necessary, adjust the sensitivity 3d Test the MLC configurationAlign the arrows on the housing rim and the dome tab Optional Accessory Installation VoiceLift SystemAttach the Z bracket to the ceiling tile and the back plate Plug VoiceLift cable into PVS 305SAOpen the sensor and loop a wire around the sensor Optional Accessory Installation Priority Page Sensor KitPriority Page Sensor Kit included parts UL-compliant junction box and coverTesting and Adjustment Procedure Typical paging system with the PVS 305SA switcher4 Sensitivity knob adjustment Reference Information PoleVault Systems Installation Reference InformationLbs 0.1 kg Wall or furniture mountable with included Decora wall plateExtron PCM Reference Information, cont’dPVS 305SA specific symbol definitions SIS CommandsSIS Command/Response Table Ascii Telnet PoleVault Systems Installation Basic SIS CommandsExtron USA West