Extron electronic PVS 305SA manual Reference Information

Page 42

Reference Information

Specifications

For detailed specifications and warranty information of the PoleVault System components, refer to the device

manuals, or the product pages at www.extron.com.

Mounting hardware

PCM 340

Mounting	Drop ceiling mountable
Maximum load	50 lbs (22.7 kg)
Material	Baseplate and pipe: aluminum, tie wire: steel, 14 AWG, 70,000 psi tensile strength
Dimensions
Base plate	1.2" H x 26.4" W x 8.0" D, (2.9 cm H x 67.0 cm W x 20.3 cm D)
Pipe	25" length, 1.5"-11.5 NPT
Adjustment ranges	1.5" - 23.0” drop, 21.5" adjustability in 0.5" steps
Product weight	4.5 lbs (2 kg)
Regulatory compliance
Safety	CE, c-UL, UL
Vibration	ISTA 1A in carton (International Safe Transit Association)

PMK 550

Mounting

Pole mount	Mountable to round projector mount poles, either standard 1.5” (3.8 cm) NPT pipes or pipes
	with an outer diameter of 1.85” to 1.95” (4.7 cm to 5.0 cm) using included hardware
Maximum load	15 lbs (6.8 kg)
Material
Base plate	Aluminum
Plate covers	High impact plastic
Dimensions	3.0" H x 15.4" W x 11.9" D (7.6 cm H x 39.1 cm W x 30.2 cm D
Product weight	2.4 lbs (1.2 kg)
Regulatory compliance
Safety	CE, c-UL, UL as an accessory for use with a UL Listed mount and projector
Vibration	ISTA 1A in carton (International Safe Transit Association)

UPB 25

Material	Steel
Maximum load	25 lbs (11.3 kg)
General dimensions	Refer to UPB 25 manual
Product weight	3.7 lbs (1.7 kg)
Regulatory compliance
Safety	CE, UL, c-UL as an accessory, for use with UL Listed mount and projector
Vibration	ISTA 1A in carton (International Safe Transit Association)

Devices

PVS 305SA

External power supply	100 VAC to 240 VAC, 50-60 Hz, external; to 12 VDC, 5 A, regulated
Power input requirements	12 VDC, 5 A
Temperature/humidity	Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
	Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling	Convection, vents on sides
Enclosure type	Metal
Enclosure dimensions	1.7" H x 8.7" W x 3.0" D (1U high, half rack wide) (4.3 cm H x 22.1 cm W x 7.6 cm D)
Product weight	2.5 lbs (1.1 kg), plus power supply 0.8 lbs (0.4 kg)

4-1 PoleVault Systems Installation • Reference Information

Image 42

Contents Installation Guide PoleVault SystemsConsignes de Sécurité Français PrecautionsSafety Instructions English Sicherheitsanleitungen DeutschPoleVault Systems Installation Introduction IntroductionFCC Class B Notice PoleVault System installation and wiring overview Introduction, contdRoom layout Typical classroom installationPoleVault Systems Installation Introduction Planning RoomLocation of the screen and projector Example classroom installationIntroduction Planning, cont’d ADA overhead and side clearance requirementsLocation of source devices Example classroom with four speaker installationLocation of MediaLink Controller and Wall Plates Cabling obstaclesIntroduction Inventory Overview InventoryIncluded items PoleVault System Devices and Hardware, cont’d Optional installation hardware Introduction Inventory Overview, cont’dItems not included Installation tools Installation Overview Outline of installation stepsPoleVault Systems Installation Installation PCM 340 Projector Drop Ceiling Mount Stage One Install the Screen and ProjectorPoleVault Systems Installation Installation Stage Slotted Pipe Supplied with PCMMark screen location Installation Stage One, cont’dInstall projector to verify location 1a Mark the screen location2e Attach the bracket to the projector 2f Slide and lock the projector onto the adjuster plateVerify the image location Horizontal offsetCut the ceiling tile Preliminary safety hardware installation5a Mark structural ceiling for lag eye bolt installation 4b Take measurements with the PCM 340 on the T-frame7a Attach turnbuckles at the corners Finish Projector Drop Ceiling Mount installationSecure the Projector Drop Ceiling Mount to the ceiling 7c Hand tighten the turnbucklesInstall the electrical box if required Install the Screen8a Install Raco box and plaster ring Stage Two Install the Wall Plates and MLC 104 IP Plus This stage involves installing the devices shown belowMLC 104 IP Plus MediaLink Controller IR/RS-232 communications cable control cable Installation Stage Two, cont’dCables RS-232 or to an IR emitterMLC 104 IP Plus mud ring Install the mud rings1d Features for mud ring installation 1c Insert the mud ringSignal Cable Label color Pull the cables at the input locations2c Pull the cables at each location Install wall plates MLC 104 IP Plus controllerInstall MediaLink Controller Wire stripping lengths4a Connecting the MLC to the switcher An RS-232 cable or IR emitter cable, as 4c Connect to the LAN using a CAT 5 cableConnect the MLC to the projector with AppropriateConnections made to the MLC 104 IP Plus 4e Secure the MLC 104 IP Plus to the mud ringStage Three Install the FF 120 Ceiling Speakers FF 120 Flat Field Ceiling Speakers2h Attach safety cable Installation Stage Three, cont’dInstall the speaker on the drop ceiling Cut ceiling tileStereo or dual mono output using parallel speaker wiring Terminate the speaker cable for the PVS switcherPole captive screw connector To terminate the cable, strip the end of the cable 0.2 inchPVS 305SA PoleVault Switcher Stage Four Install the PMK 550 and the PVS 305SAThis stage covers installing the devices shown below PMK 550 Pole Mount KitInstall the PMK 550 base plate PoleVault Systems Installation Installation Stage 4Switcher and projector cable overview Installation Stage Four, cont’dPull the cables at the switcher location 2b Gather the cables, pass them down the pipe4a Connect the cables to the switcher Finish installing the Pole Mount kitBControl/power cable from the MLC 104 IP Plus Connect the cables as follows to the PVS 305SA4b Reattach UPB bracket and 4c projector 4d Cable the projectorStage Five Configure the Switcher and the System Configure the switcher MLS Switcher Configuration programGlobal configurator software Installation Stage Five, cont’d Configure the system Global ConfiguratorLoosen all pivot screws and adjust the vertical angle 3c Check that an image is present, adjust as neededTest the system Where installed, if necessary, adjust the sensitivity Final installationAdjust the configuration as necessary 3d Test the MLC configuration Attach the Z bracket to the ceiling tile and the back plate Optional Accessory Installation VoiceLift System Align the arrows on the housing rim and the dome tab Plug VoiceLift cable into PVS 305SAPriority Page Sensor Kit included parts Optional Accessory Installation Priority Page Sensor KitOpen the sensor and loop a wire around the sensor UL-compliant junction box and coverTesting and Adjustment Procedure Typical paging system with the PVS 305SA switcher4 Sensitivity knob adjustment PoleVault Systems Installation Reference Information Reference InformationWall or furniture mountable with included Decora wall plate Lbs 0.1 kgReference Information, cont’d Extron PCMSIS Command/Response Table Ascii Telnet SIS CommandsPVS 305SA specific symbol definitions PoleVault Systems Installation Basic SIS CommandsExtron USA West