Schneider Electric AP9635 manual Introduction, Product Description, Features

Page 10

Introduction

Product Description

Features

The American Power Conversion Network Management Card (AP9635) is a Web-based product that manages supported devices using multiple, open standards such as Hypertext Transfer Protocol (HTTP), Telnet, Hypertext Transfer Protocol over Secure Sockets Layer (HTTPS), Secure SHell (SSH), Simple Network Management Protocol (SNMP), File Transfer Protocol (FTP), and Secure CoPy (SCP). The Network Management Card:

•Provides data and event logs

•Provides support for the PowerChute® Network Shutdown utility

•Supports using a Dynamic Host Configuration Protocol (DHCP) or BOOTstrap Protocol (BOOTP) server to provide the network (TCP/IP) values of the Management Card

•Supports using the Remote Monitoring Service (RMS)

•Supports remote monitoring over modem using Tele Service Connect (TLS) (MGE® Galaxy® 300 and MGE Galaxy 7000 only). Contact APC Support for information.

•Enables you to configure notification through event logging (by the Management Card and Syslog), e-mail, and SNMP traps. You can configure notification for single events or groups of events, based on the severity level or category of events

•Provides the ability to export a user configuration (.ini) file from a configured card to one or more unconfigured cards without converting the file to a binary file

•Provides a selection of security protocols for authentication and encryption

•Communicates with InfraStruxure® Central

•Supports Modbus RTU over a serial RS485 port

•Supports Modbus over TCP (Symmetra® PX 250 and 500 only)

Devices in which you can install the Management Card. The AP9635 Network Management Card can be installed into the Symmetra PX 250, Symmetra PX 500, MGE Galaxy 300, and MGE Galaxy 7000 UPS devices.

Note: The Network Management Card ships with the firmware for the MGE Galaxy 300 and MGE Galaxy 7000 already installed. If you are ordering the card as a replacement part for a Symmetra PX 250 or Symmetra PX 500, you will need to install the Symmetra-specific firmware. Contact APC Worldwide Customer Support for more information. See “APC Worldwide Customer Support” on page 96.

1	Network Management Card User’s Guide

Image 10

Contents User’s Guide 동봉된 CD 안에 한국어 매뉴얼이 있습니다 Contents Web Interface Monitor the UPS and Configure Shutdowns Logs Administration Notification Troubleshooting Appendix a List of Supported Commands Introduction FeaturesProduct Description Network management features Internal Management FeaturesInitial setup OverviewAccess priority for logging on Types of user accountsHow to Recover from a Lost Password Front Panel DescriptionCondition Description Status LEDLink-RX/TX 10/100 LED Resetting the network timer Watchdog FeaturesNetwork interface watchdog mechanism How To Log On Command Line InterfaceRemote access to the command line interface Sample main screen Main ScreenInformation and status fields Two fields report when you logged in, by date and time Entering commands Using the Command Line InterfaceCommand syntax Code Error message Command Response CodesSyntax examples About Command DescriptionsAlarmcount Option Arguments DescriptionBoot Option Argument DescriptionConsole DateDir DeleteArgument Description DnsExit EventlogKey Description FormatHelp FtpOption Argument Definition ModbusNtp NetstatPing Prompt PortSpeedQuit Reboot RadiusSnmp, snmp3 ResetToDefSystem Tcpip Tcpip6Tls Uio UpsUser XferINI WebXferStatus Introduction Web InterfaceSupported Web browsers Error Message Browser Cause of the Error URL address formatsIcon Description HomeQuick status icons Recent Device EventsMenus How to Use the Tabs, Menus, and LinksTabs Quick LinksOperating state Monitor the UPS and Configure ShutdownsOverview Operating State Icon DescriptionRecent UPS Events StatusModel-specific status displayed PowerChute Option PowerChute Network Shutdown clientsPowerChute Network Shutdown configuration parameters Parameter DescriptionAbout Option Environmental Monitoring Heading Displayed InformationBrief status Temperature and HumidityDetailed status and configuration Threshold DescriptionUPS Network Management Card 2 User’s Guide Input Contacts Output Relay AboutConfiguring an output to respond to an event Configuring the Control PolicyConfiguring the UPS or output to respond to an input alarm Event log LogsUse the Event and Data Logs Launch Log in New Window buttonData log To display the data log Logs Data log To set the data collection interval Logs Data interval How to use FTP or SCP to retrieve log files Scp username@hostnameoripaddressevent.csv ./event.csv Syslog servers Authentication Administration SecuritySetting user access Local UsersRadius Setting Definition RadiusConfiguring a Radius server on Unix with shadow passwords Configuring the Radius ServerSummary of the configuration procedure Supported Radius serversInactivity Timeout TCP/IP settings Administration Network FeaturesTCP/IP and Communication Settings Setting DescriptionDhcp response options APC Cookie. Tag 1, Len 4, Data 1APCPing Response Port Speed DNSQuery Type Selected Query Question to Use Web Option DescriptionConsole Snmp SNMPv1SNMPv3 Modbus FTP Server Event Actions Administration NotificationConfiguring event actions Types of notificationNetwork Management Card User’s Guide Active, Automatic, Direct Notification Mail notificationIdentify up to four e-mail recipients Snmp traps Snmp Trap TestSetting Definition Remote Monitoring ServiceSyslog Syslog Settings Path Logs Syslog settings Set the Date and Time Administration General OptionsIdentification MethodUse an .ini File Daylight savingSpecify a default login Event Log, Temperature Units, and Log-InChange the default temperature scale Color-code event log textAbout the Management Card Reset the Management CardConfigure Links Action DefinitionHow to use the Wizard to configure TCP/IP settings Device IP Configuration WizardCapabilities, Requirements, and Installation InstallationUse the Wizard Configure the basic TCP/IP settings remotelySelect Remotely over the network, and click Next Configure or reconfigure the TCP/IP settings locally Select Locally through the serial port, and click NextContents of the .ini file How to Export Configuration SettingsSummary of the procedure Detailed proceduresFtp put filename.ini Messages in config.ini Upload Event and Error MessagesEvent and its error messages Errors generated by overridden valuesRelated Topics Benefits of upgrading firmware How to Upgrade FirmwareFile Transfers Firmware files Network Management CardUse FTP or SCP to upgrade one Management Card Firmware File Transfer MethodsHow to upgrade multiple Management Cards Use Xmodem to upgrade one Management Card Use a USB drive to transfer the files Verifying Upgrades and UpdatesVerify the version numbers of installed firmware Verify the success or failure of the transferAdding and Changing Language Packs Management Card Access Problems TroubleshootingProblem Solution Snmp Issues GETAppendix a List of Supported Commands Network Management Card User’s Guide Network Management Card User’s Guide Terms of warranty Two-Year Factory WarrantyNon-transferable warranty Exclusions Warranty claims APC Worldwide Customer Support 990-3197B-001 2011