Schneider Electric AP9635 manual How to Recover from a Lost Password

Page 13

How to Recover from a Lost Password

You can use a local computer that connects to the Management Card through the serial port to access the command line interface.

1.Select a serial port at the local computer, and disable any service that uses that port.

2.Connect the provided serial cable (part number 940-0299) to the selected port at the computer and to the configuration port at the Management Card.

3.Run a terminal program (such as HyperTerminal®) and configure the selected port for 9600 bps, 8 data bits, no parity, 1 stop bit, and no flow control.

4.Press ENTER, repeatedly if necessary, to display the User Name prompt. If you are unable to display the User Name prompt, verify the following:

–The serial port is not in use by another application.

–The terminal settings are correct as specified in step 3.

–The correct cable is being used as specified in step 2.

5.Press the Reset button. The Status LED will flash alternately orange and green. Press the Reset button a second time immediately while the LED is flashing to reset the user name and password to their defaults temporarily.

6.Press ENTER, repeatedly if necessary, to display the User Name prompt again, then use the default, apc, for the user name and password. (If you take longer than 30 seconds to log on after the User Name prompt is redisplayed, you must repeat step 5 and log on again.)

7.At the command line interface, use the following commands to change the User Name and Password settings, both of which are now apc:

user -anyourAdministratorName

user -apyourAdministratorPassword

For example, to change the Administrator user name to Admin, type:

user -an Admin

8.Type quit or exit to log off, reconnect any serial cable you disconnected, and restart any service you disabled.

Network Management Card User’s Guide

4

Image 13

Contents User’s Guide 동봉된 CD 안에 한국어 매뉴얼이 있습니다 Contents Web Interface Monitor the UPS and Configure Shutdowns Logs Administration Notification Troubleshooting Appendix a List of Supported Commands Introduction FeaturesProduct Description Initial setup Internal Management FeaturesNetwork management features OverviewTypes of user accounts Access priority for logging onHow to Recover from a Lost Password Description Front PanelCondition Description Status LEDLink-RX/TX 10/100 LED Resetting the network timer Watchdog FeaturesNetwork interface watchdog mechanism How To Log On Command Line InterfaceRemote access to the command line interface Sample main screen Main ScreenInformation and status fields Two fields report when you logged in, by date and time Entering commands Using the Command Line InterfaceCommand syntax Code Error message Command Response CodesSyntax examples Alarmcount Command DescriptionsAbout Option Arguments DescriptionOption Argument Description BootDate ConsoleArgument Description DeleteDir DnsKey Description EventlogExit FormatOption Argument Definition FtpHelp ModbusNtp NetstatPing Prompt PortSpeedQuit Radius RebootSnmp, snmp3 ResetToDefSystem Tcpip6 TcpipTls Ups UioUser XferINI WebXferStatus Introduction Web InterfaceSupported Web browsers URL address formats Error Message Browser Cause of the ErrorQuick status icons HomeIcon Description Recent Device EventsTabs How to Use the Tabs, Menus, and LinksMenus Quick LinksOverview Monitor the UPS and Configure ShutdownsOperating state Operating State Icon DescriptionRecent UPS Events StatusModel-specific status displayed PowerChute Network Shutdown clients PowerChute OptionParameter Description PowerChute Network Shutdown configuration parametersAbout Option Heading Displayed Information Environmental MonitoringDetailed status and configuration Temperature and HumidityBrief status Threshold DescriptionUPS Network Management Card 2 User’s Guide Input Contacts About Output RelayConfiguring an output to respond to an event Configuring the Control PolicyConfiguring the UPS or output to respond to an input alarm Use the Event and Data Logs LogsEvent log Launch Log in New Window buttonData log To display the data log Logs Data log To set the data collection interval Logs Data interval How to use FTP or SCP to retrieve log files Scp username@hostnameoripaddressevent.csv ./event.csv Syslog servers Setting user access Administration SecurityAuthentication Local UsersRadius Radius Setting DefinitionSummary of the configuration procedure Configuring the Radius ServerConfiguring a Radius server on Unix with shadow passwords Supported Radius serversInactivity Timeout TCP/IP and Communication Settings Administration Network FeaturesTCP/IP settings Setting DescriptionAPC Cookie. Tag 1, Len 4, Data 1APC Dhcp response optionsPing Response DNS Port SpeedQuery Type Selected Query Question to Use Option Description WebConsole SNMPv1 SnmpSNMPv3 Modbus FTP Server Configuring event actions Administration NotificationEvent Actions Types of notificationNetwork Management Card User’s Guide Mail notification Active, Automatic, Direct NotificationIdentify up to four e-mail recipients Snmp Trap Test Snmp trapsSetting Definition Remote Monitoring ServiceSyslog Syslog Settings Path Logs Syslog settings Identification Administration General OptionsSet the Date and Time MethodDaylight saving Use an .ini FileChange the default temperature scale Event Log, Temperature Units, and Log-InSpecify a default login Color-code event log textConfigure Links Reset the Management CardAbout the Management Card Action DefinitionCapabilities, Requirements, and Installation Device IP Configuration WizardHow to use the Wizard to configure TCP/IP settings InstallationUse the Wizard Configure the basic TCP/IP settings remotelySelect Remotely over the network, and click Next Select Locally through the serial port, and click Next Configure or reconfigure the TCP/IP settings locallySummary of the procedure How to Export Configuration SettingsContents of the .ini file Detailed proceduresFtp put filename.ini Event and its error messages Upload Event and Error MessagesMessages in config.ini Errors generated by overridden valuesRelated Topics File Transfers How to Upgrade FirmwareBenefits of upgrading firmware Firmware files Network Management CardFirmware File Transfer Methods Use FTP or SCP to upgrade one Management CardHow to upgrade multiple Management Cards Use Xmodem to upgrade one Management Card Verify the version numbers of installed firmware Verifying Upgrades and UpdatesUse a USB drive to transfer the files Verify the success or failure of the transferAdding and Changing Language Packs Management Card Access Problems TroubleshootingProblem Solution GET Snmp IssuesAppendix a List of Supported Commands Network Management Card User’s Guide Network Management Card User’s Guide Terms of warranty Two-Year Factory WarrantyNon-transferable warranty Exclusions Warranty claims 990-3197B-001 2011 APC Worldwide Customer Support