Schneider Electric AP9635 manual Remote Monitoring Service, Syslog, Setting Definition

Page 79

To. Select the IP address or host name to which a test SNMP trap will be sent. If no trap receiver is configured, a link to the Trap Receiver configuration page is displayed.

Remote Monitoring Service

Path: Administration > Notification > Remote Monitoring

The Remote Monitoring Service (RMS) is an optional service that monitors your system from a remote operation center 24 hours a day, 7 days a week, and notifies you of device and system events.

To purchase the RMS service, contact your American Power Conversion vendor or see the RMS Web site, rms.apc.com.

Registration. To activate RMS for the Management Card, select Enable APC Remote Monitoring Service., choose between Register Company and Device and Register Device Only, complete the form, and click Send APC RMS Registration.

Use the Reset APC Remote Monitoring Service Registration check box to discontinue the service, whether permanently or temporarily (for example, if you are moving a Management Card).

Syslog

Path: Logs > Syslog > options

The Management Card can send messages to up to four Syslog servers when an event occurs. The Syslog servers record events that occur at network devices in a log that provides a centralized record of events.

This user’s guide does not describe Syslog or its configuration values in detail. See RFC3164 for more information about Syslog.

Identifying Syslog Servers.

Path: Logs > Syslog > servers

Setting

Definition

 

 

Syslog Server

Uses IPv4/ IPv6 addresses or host names to identify from one to four servers to receive

 

Syslog messages sent by the Management Card.

 

 

Port

The user datagram protocol (UDP) port that the Management Card will use to send Syslog

 

messages. The default is 514, the UDP port assigned to Syslog.

 

 

Protocol

Choose between UDP and TCP.

 

 

Language

Choose the language for any Syslog messages.

 

 

Network Management Card User’s Guide

70

Image 79
Contents User’s Guide 동봉된 CD 안에 한국어 매뉴얼이 있습니다 Contents Web Interface Monitor the UPS and Configure Shutdowns Logs Administration Notification Troubleshooting Appendix a List of Supported Commands Introduction FeaturesProduct Description Overview Internal Management FeaturesInitial setup Network management featuresTypes of user accounts Access priority for logging onHow to Recover from a Lost Password Description Front PanelCondition Description Status LEDLink-RX/TX 10/100 LED Resetting the network timer Watchdog FeaturesNetwork interface watchdog mechanism How To Log On Command Line InterfaceRemote access to the command line interface Sample main screen Main ScreenInformation and status fields Two fields report when you logged in, by date and time Entering commands Using the Command Line InterfaceCommand syntax Code Error message Command Response CodesSyntax examples Option Arguments Description Command DescriptionsAlarmcount AboutOption Argument Description BootDate ConsoleDns DeleteArgument Description DirFormat EventlogKey Description ExitModbus FtpOption Argument Definition HelpNtp NetstatPing Prompt PortSpeedQuit Radius RebootSnmp, snmp3 ResetToDefSystem Tcpip6 TcpipTls Ups UioUser XferINI WebXferStatus Introduction Web InterfaceSupported Web browsers URL address formats Error Message Browser Cause of the ErrorRecent Device Events HomeQuick status icons Icon DescriptionQuick Links How to Use the Tabs, Menus, and LinksTabs MenusOperating State Icon Description Monitor the UPS and Configure ShutdownsOverview Operating stateRecent UPS Events StatusModel-specific status displayed PowerChute Network Shutdown clients PowerChute OptionParameter Description PowerChute Network Shutdown configuration parametersAbout Option Heading Displayed Information Environmental MonitoringThreshold Description Temperature and HumidityDetailed status and configuration Brief statusUPS Network Management Card 2 User’s Guide Input Contacts About Output RelayConfiguring an output to respond to an event Configuring the Control PolicyConfiguring the UPS or output to respond to an input alarm Launch Log in New Window button LogsUse the Event and Data Logs Event logData log To display the data log Logs Data log To set the data collection interval Logs Data interval How to use FTP or SCP to retrieve log files Scp username@hostnameoripaddressevent.csv ./event.csv Syslog servers Local Users Administration SecuritySetting user access AuthenticationRadius Radius Setting DefinitionSupported Radius servers Configuring the Radius ServerSummary of the configuration procedure Configuring a Radius server on Unix with shadow passwordsInactivity Timeout Setting Description Administration Network FeaturesTCP/IP and Communication Settings TCP/IP settingsAPC Cookie. Tag 1, Len 4, Data 1APC Dhcp response optionsPing Response DNS Port SpeedQuery Type Selected Query Question to Use Option Description WebConsole SNMPv1 SnmpSNMPv3 Modbus FTP Server Types of notification Administration NotificationConfiguring event actions Event ActionsNetwork Management Card User’s Guide Mail notification Active, Automatic, Direct NotificationIdentify up to four e-mail recipients Snmp Trap Test Snmp trapsSetting Definition Remote Monitoring ServiceSyslog Syslog Settings Path Logs Syslog settings Method Administration General OptionsIdentification Set the Date and TimeDaylight saving Use an .ini FileColor-code event log text Event Log, Temperature Units, and Log-InChange the default temperature scale Specify a default loginAction Definition Reset the Management CardConfigure Links About the Management CardInstallation Device IP Configuration WizardCapabilities, Requirements, and Installation How to use the Wizard to configure TCP/IP settingsUse the Wizard Configure the basic TCP/IP settings remotelySelect Remotely over the network, and click Next Select Locally through the serial port, and click Next Configure or reconfigure the TCP/IP settings locallyDetailed procedures How to Export Configuration SettingsSummary of the procedure Contents of the .ini fileFtp put filename.ini Errors generated by overridden values Upload Event and Error MessagesEvent and its error messages Messages in config.iniRelated Topics Firmware files Network Management Card How to Upgrade FirmwareFile Transfers Benefits of upgrading firmwareFirmware File Transfer Methods Use FTP or SCP to upgrade one Management CardHow to upgrade multiple Management Cards Use Xmodem to upgrade one Management Card Verify the success or failure of the transfer Verifying Upgrades and UpdatesVerify the version numbers of installed firmware Use a USB drive to transfer the filesAdding and Changing Language Packs Management Card Access Problems TroubleshootingProblem Solution GET Snmp IssuesAppendix a List of Supported Commands Network Management Card User’s Guide Network Management Card User’s Guide Terms of warranty Two-Year Factory WarrantyNon-transferable warranty Exclusions Warranty claims 990-3197B-001 2011 APC Worldwide Customer Support