Schneider Electric AP9635 manual Port Speed, Dns

Page 66

Port Speed

Path: Administration > Network > Port Speed

The Port Speed setting defines the communication speed of the TCP/IP port.

For Auto-negotiation(the default), Ethernet devices negotiate to transmit at the highest possible speed, but if the supported speeds of two devices are unmatched, the slower speed is used.

Alternatively, you can choose 10 Mbps or 100 Mbps, each with the option of half-duplex (communication in only one direction at a time) or full-duplex (communication in both directions on the same channel simultaneously).

DNS

Path: Administration > Network > DNS > options

Use the options under DNS on the left navigation menu to configure and test the Domain Name System (DNS):

Select servers to specify the IP addresses of the primary and optional secondary DNS server. For the Management Card to send e-mail, at least the IP address of the primary DNS server must be defined.

The Management Card waits up to 15 seconds for a response from the primary DNS server or the secondary DNS server (if a secondary DNS server is specified). If the Management Card does not receive a response within that time, e-mail cannot be sent. Therefore, use DNS servers on the same segment as the Management Card or on a nearby segment (but not across a wide-area network [WAN]).

After you define the IP addresses of the DNS servers, verify that DNS is working correctly by entering the DNS name of a computer on your network to look up the IP address for that computer.

Select naming to define the host name and domain name of the Management Card:

Host Name: After you configure a host name here and a domain name in the Domain Name field, users can enter a host name in any field in the Management Card interface (except e-mail addresses) that accepts a domain name.

Domain Name (IPv4): You need to configure the domain name here only. In all other fields in the Management Card interface (except e-mail addresses) that accept domain names, the Management Card adds this domain name when only a host name is entered.

To override all instances of the expansion of a specified host name by the addition of the domain name, set the domain name field to its default, somedomain.com, or to

0.0.0.0.

To override the expansion of a specific host name entry (for example, when defining a trap receiver), include a trailing period. The Management Card recognizes a host name with a trailing period (such as mySnmpServer.) as if it were a fully qualified domain name and does not append the domain name.

Domain Name (IPv6): Specify the IPv6 domain name here.

57

Network Management Card User’s Guide

Image 66
Contents User’s Guide 동봉된 CD 안에 한국어 매뉴얼이 있습니다 Contents Web Interface Monitor the UPS and Configure Shutdowns Logs Administration Notification Troubleshooting Appendix a List of Supported Commands Features IntroductionProduct Description Network management features Internal Management FeaturesInitial setup OverviewAccess priority for logging on Types of user accountsHow to Recover from a Lost Password Front Panel DescriptionStatus LED Condition DescriptionLink-RX/TX 10/100 LED Watchdog Features Resetting the network timerNetwork interface watchdog mechanism Command Line Interface How To Log OnRemote access to the command line interface Main Screen Sample main screenInformation and status fields Two fields report when you logged in, by date and time Using the Command Line Interface Entering commandsCommand syntax Command Response Codes Code Error messageSyntax examples About Command DescriptionsAlarmcount Option Arguments DescriptionBoot Option Argument DescriptionConsole DateDir DeleteArgument Description DnsExit EventlogKey Description FormatHelp FtpOption Argument Definition ModbusNetstat NtpPing PortSpeed PromptQuit Reboot RadiusResetToDef Snmp, snmp3System Tcpip Tcpip6Tls Uio UpsUser Web XferINIXferStatus Web Interface IntroductionSupported Web browsers Error Message Browser Cause of the Error URL address formatsIcon Description HomeQuick status icons Recent Device EventsMenus How to Use the Tabs, Menus, and LinksTabs Quick LinksOperating state Monitor the UPS and Configure ShutdownsOverview Operating State Icon DescriptionStatus Recent UPS EventsModel-specific status displayed PowerChute Option PowerChute Network Shutdown clientsPowerChute Network Shutdown configuration parameters Parameter DescriptionAbout Option Environmental Monitoring Heading Displayed InformationBrief status Temperature and HumidityDetailed status and configuration Threshold DescriptionUPS Network Management Card 2 User’s Guide Input Contacts Output Relay AboutConfiguring the Control Policy Configuring an output to respond to an eventConfiguring the UPS or output to respond to an input alarm Event log LogsUse the Event and Data Logs Launch Log in New Window buttonData log To display the data log Logs Data log To set the data collection interval Logs Data interval How to use FTP or SCP to retrieve log files Scp username@hostnameoripaddressevent.csv ./event.csv Syslog servers Authentication Administration SecuritySetting user access Local UsersRadius Setting Definition RadiusConfiguring a Radius server on Unix with shadow passwords Configuring the Radius ServerSummary of the configuration procedure Supported Radius serversInactivity Timeout TCP/IP settings Administration Network FeaturesTCP/IP and Communication Settings Setting DescriptionDhcp response options APC Cookie. Tag 1, Len 4, Data 1APCPing Response Port Speed DNSQuery Type Selected Query Question to Use Web Option DescriptionConsole Snmp SNMPv1SNMPv3 Modbus FTP Server Event Actions Administration NotificationConfiguring event actions Types of notificationNetwork Management Card User’s Guide Active, Automatic, Direct Notification Mail notificationIdentify up to four e-mail recipients Snmp traps Snmp Trap TestRemote Monitoring Service Setting DefinitionSyslog Syslog Settings Path Logs Syslog settings Set the Date and Time Administration General OptionsIdentification MethodUse an .ini File Daylight savingSpecify a default login Event Log, Temperature Units, and Log-InChange the default temperature scale Color-code event log textAbout the Management Card Reset the Management CardConfigure Links Action DefinitionHow to use the Wizard to configure TCP/IP settings Device IP Configuration WizardCapabilities, Requirements, and Installation InstallationConfigure the basic TCP/IP settings remotely Use the WizardSelect Remotely over the network, and click Next Configure or reconfigure the TCP/IP settings locally Select Locally through the serial port, and click NextContents of the .ini file How to Export Configuration SettingsSummary of the procedure Detailed proceduresFtp put filename.ini Messages in config.ini Upload Event and Error MessagesEvent and its error messages Errors generated by overridden valuesRelated Topics Benefits of upgrading firmware How to Upgrade FirmwareFile Transfers Firmware files Network Management CardUse FTP or SCP to upgrade one Management Card Firmware File Transfer MethodsHow to upgrade multiple Management Cards Use Xmodem to upgrade one Management Card Use a USB drive to transfer the files Verifying Upgrades and UpdatesVerify the version numbers of installed firmware Verify the success or failure of the transferAdding and Changing Language Packs Troubleshooting Management Card Access ProblemsProblem Solution Snmp Issues GETAppendix a List of Supported Commands Network Management Card User’s Guide Network Management Card User’s Guide Two-Year Factory Warranty Terms of warrantyNon-transferable warranty Exclusions Warranty claims APC Worldwide Customer Support 990-3197B-001 2011