Schneider Electric AP9635 manual Administration Notification, Event Actions, Types of notification

Page 74

Administration: Notification

Event Actions

Path: Administration > Notification > Event Actions > options

Types of notification

You can configure event actions to occur in response to an event or group of events. These actions notify users of the event in any of several ways:

Active, automatic notification. The specified users or monitoring devices are contacted directly.

E-mail notification

SNMP traps

Remote Monitoring Service

Syslog notification

Indirect notification

Event log. If no direct notification is configured, users must check the log to determine which events have occurred.

You can also log system performance data to use for device monitoring. See “Data log” on page 44 for information on how to configure and use this data logging

option.

– Queries (SNMP GETs)

For more information, see “SNMP” on page 61. SNMP enables an NMS to perform informational queries. For SNMPv1, which does not encrypt data before transmission, configuring the most restrictive SNMP access type (READ) enables informational queries without the risk of allowing remote configuration changes.

Configuring event actions

Notification parameters. For events that have an associated clearing event, you can also set the following parameters as you configure events individually or by group, as described in the next two sections. To access the parameters, click the receiver or recipient name.

Parameter

Description

 

 

Delay x time before

If the event persists for the specified time, notification is sent. If the condition clears

sending

before the time expires, no notification is sent.

 

 

Repeat at an

The notification is sent at the specified interval (e.g., every 2 minutes).

interval of x time

 

 

 

Up to x times

During an active event, the notification repeats for this number of times.

 

 

Until condition

The notification is sent repeatedly until the condition clears or is resolved.

clears

 

 

 

65

Network Management Card User’s Guide

Image 74
Contents User’s Guide 동봉된 CD 안에 한국어 매뉴얼이 있습니다 Contents Web Interface Monitor the UPS and Configure Shutdowns Logs Administration Notification Troubleshooting Appendix a List of Supported Commands Product Description FeaturesIntroduction Network management features Internal Management FeaturesInitial setup OverviewAccess priority for logging on Types of user accountsHow to Recover from a Lost Password Front Panel DescriptionLink-RX/TX 10/100 LED Status LEDCondition Description Network interface watchdog mechanism Watchdog FeaturesResetting the network timer Remote access to the command line interface Command Line InterfaceHow To Log On Information and status fields Main ScreenSample main screen Two fields report when you logged in, by date and time Command syntax Using the Command Line InterfaceEntering commands Syntax examples Command Response CodesCode Error message About Command DescriptionsAlarmcount Option Arguments DescriptionBoot Option Argument DescriptionConsole DateDir DeleteArgument Description DnsExit EventlogKey Description FormatHelp FtpOption Argument Definition ModbusPing NetstatNtp Quit PortSpeedPrompt Reboot RadiusSystem ResetToDefSnmp, snmp3 Tcpip Tcpip6Tls Uio UpsUser XferStatus WebXferINI Supported Web browsers Web InterfaceIntroduction Error Message Browser Cause of the Error URL address formatsIcon Description HomeQuick status icons Recent Device EventsMenus How to Use the Tabs, Menus, and LinksTabs Quick LinksOperating state Monitor the UPS and Configure ShutdownsOverview Operating State Icon DescriptionModel-specific status displayed StatusRecent UPS Events PowerChute Option PowerChute Network Shutdown clientsPowerChute Network Shutdown configuration parameters Parameter DescriptionAbout Option Environmental Monitoring Heading Displayed InformationBrief status Temperature and HumidityDetailed status and configuration Threshold DescriptionUPS Network Management Card 2 User’s Guide Input Contacts Output Relay AboutConfiguring the UPS or output to respond to an input alarm Configuring the Control PolicyConfiguring an output to respond to an event Event log LogsUse the Event and Data Logs Launch Log in New Window buttonData log To display the data log Logs Data log To set the data collection interval Logs Data interval How to use FTP or SCP to retrieve log files Scp username@hostnameoripaddressevent.csv ./event.csv Syslog servers Authentication Administration SecuritySetting user access Local UsersRadius Setting Definition RadiusConfiguring a Radius server on Unix with shadow passwords Configuring the Radius ServerSummary of the configuration procedure Supported Radius serversInactivity Timeout TCP/IP settings Administration Network FeaturesTCP/IP and Communication Settings Setting DescriptionDhcp response options APC Cookie. Tag 1, Len 4, Data 1APCPing Response Port Speed DNSQuery Type Selected Query Question to Use Web Option DescriptionConsole Snmp SNMPv1SNMPv3 Modbus FTP Server Event Actions Administration NotificationConfiguring event actions Types of notificationNetwork Management Card User’s Guide Active, Automatic, Direct Notification Mail notificationIdentify up to four e-mail recipients Snmp traps Snmp Trap TestSyslog Remote Monitoring ServiceSetting Definition Syslog Settings Path Logs Syslog settings Set the Date and Time Administration General OptionsIdentification MethodUse an .ini File Daylight savingSpecify a default login Event Log, Temperature Units, and Log-InChange the default temperature scale Color-code event log textAbout the Management Card Reset the Management CardConfigure Links Action DefinitionHow to use the Wizard to configure TCP/IP settings Device IP Configuration WizardCapabilities, Requirements, and Installation InstallationSelect Remotely over the network, and click Next Configure the basic TCP/IP settings remotelyUse the Wizard Configure or reconfigure the TCP/IP settings locally Select Locally through the serial port, and click NextContents of the .ini file How to Export Configuration SettingsSummary of the procedure Detailed proceduresFtp put filename.ini Messages in config.ini Upload Event and Error MessagesEvent and its error messages Errors generated by overridden valuesRelated Topics Benefits of upgrading firmware How to Upgrade FirmwareFile Transfers Firmware files Network Management CardUse FTP or SCP to upgrade one Management Card Firmware File Transfer MethodsHow to upgrade multiple Management Cards Use Xmodem to upgrade one Management Card Use a USB drive to transfer the files Verifying Upgrades and UpdatesVerify the version numbers of installed firmware Verify the success or failure of the transferAdding and Changing Language Packs Problem Solution TroubleshootingManagement Card Access Problems Snmp Issues GETAppendix a List of Supported Commands Network Management Card User’s Guide Network Management Card User’s Guide Non-transferable warranty Exclusions Two-Year Factory WarrantyTerms of warranty Warranty claims APC Worldwide Customer Support 990-3197B-001 2011