Sharp MX-FX13 appendix Initial Setting, 100, Dial Mode, Pause Time

Page 102

SYSTEM SETTINGS

2

Select "LIST PRINT/SET" with the [

] or

 

[

] key and then press the [OK] key.

3

Select "LIST SETTING" with the [

] or [ ]

 

key and then press the [OK] key.

 

4

Select "AUTO LISTING" with the [

] or

 

[

] key and then press the [OK] key.

5

Select "AUTO PRINT REPT AT LIMIT (50)"

 

with the [ ] or [ ] key and then press the

[OK] key.

•The setting is enabled and a checkmark appears in the checkbox.

•If this procedure is performed when the setting is enabled, the checkmark will be cleared and the setting disabled.

6

If you wish to have the activity report

 

printed at regular intervals, go to step 7. If

 

you have finished selecting settings,

 

press the [BACK] key.

7

Select "PRINT DAILY AT DESIGNATED

 

TIME" with the [

] or [ ] key and then

 

press the [OK] key.

8

Select "SETTING" with the [ ] or [ ] key

 

and then press the [OK] key.

9

Enter the printout time with the numeric

 

keys and press the [OK] key.

 

If you make a mistake, move the cursor to the incorrect

 

digit with the [ ] or [

] key (the cursor should be over

the digit), and then enter the correct digit.

• After step 9 you will return to step 8. If you

Note need to change the set time, follow steps 8 and 9 to enter the new time.

•To cancel a "PRINT DAILY AT DESIGNATED TIME" setting, follow these steps:

(1)Select "CANCEL" in step 8 and then press the [OK] key.

(2)Select "CANCEL" with the [ ] or [ ] key and then press the [OK] key.

•If "AUTO PRINT REPT AT LIMIT (50)" is not enabled and the number of recorded transactions exceeds 50, each new transaction will delete the oldest transaction.

•The activity report can also be printed out on demand. (See "PRINTING LISTS OF PROGRAMMED INFORMATION, SETTINGS, AND COMMUNICATION ACTIVITY" on page 85.)

INITIAL SETTING

These settings are used to change the default settings (initially set at the factory) for the various fax functions to settings that better meet your needs.

DIAL MODE

This setting is used to set the appropriate dial mode for the line connected to the machine. Select tone for a tone dial line or pulse for a pulse dial line. Most lines use tone dialling.

1 Follow steps 1 through 6 of "INITIAL PROCEDURE" (page 98).

2 Select "INITIAL SETTING" with the [ ] or [ ] key and then press the [OK] key.

3 Select "DIAL MODE" with the [ ] or [ ] key and then press the [OK] key.

4 Select "TONE" or "PULSE" with the [ ] or [ ] key and then press the [OK] key.

Select the appropriate mode for your telephone line type.

PAUSE TIME

This setting is used to select the duration of pauses that are inserted in destination fax numbers. Normally the setting is 2 seconds, which means that each time the [PAUSE] key is pressed when dialling or storing a fax number, a pause of 2 seconds is inserted. The pause time can be set to any number of seconds from 1 to 15.

1 Follow steps 1 through 6 of "INITIAL PROCEDURE" (page 98).

2 Select "INITIAL SETTING" with the [ ] or [ ] key and then press the [OK] key.

3 Select "PAUSE TIME" with the [ ] or [ ] key and then press the [OK] key.

4 Enter the pause time in seconds ("01" to

"15") with the numeric keys and then press the [OK] key.

If you make a mistake, move the cursor to the incorrect digit with the [ ] or [ ] key (the cursor should be over the digit), and then enter the correct digit.

100

Page 101 Page 103
Image 102
Page 101 Page 103
Contents Codes 112Function Telecommunication Line Cable Connecting AN Extension Phone Connecting AN Extension PhoneIntroduction Contents 113 Report112 AT Regular Intervals Communication activityPower switch To USE this Product Correctly AS a FacsimileLine connection Lithium battery Please noteSet the date and time Points to Check and Program After InstallationPaper sizes that can be used for fax mode Program the senders name and senders numberPart Names and Functions Operation PanelOriginal Size key Address keyBroadcast key Duplex Scan keyFAX Mode Base Screen Base screen of fax modeAuditing Mode Using auditing modeEnter your account number five digits with the numeric keys Original sizes OriginalsOriginals That can be Faxed Scanning area of originalPlacing the Original Using the SPF/RSPFUsing the Document Glass Difference between A4 8-1/2 x 11 and A4R 8-1/2 x 11RA4R Manually Setting the Scanning SizeMemory Auto AutoStandard ResolutionResolution Standard FineXxxxxx RediallingON-HOOK Dialling Basic Operations Original Size Basic Procedure for Sending FaxesSending a FAX Memory Auto A4RMemory Auto Auto A4R Standard Reading XX%Read END XX% Press the Start keySending a FAX by Speed Dialling MemoryOksearch KEY WordsAddress Select the desired destination with the or keySided Faxing a TWO-SIDED Original MX-M182D/MX-M202D/MX-M232DSided Duplex ScanSelect TX with the or key Select Sending Memory TXDirect TX Select Direct TX with the or keyFaxing by manual transmission using the Speaker key Storing transmission jobs memory transmissionEnter Dial # If the receiving party is busy If a transmission error occursQuick On-line Image rotationJobs Cancelling a FAX TransmissionCancelling a fax transmission YESJobs Cancelling a stored transmission jobSerial Poll Mode XXX ReserveReceiving a FAX Line indicator lights upReceiving Faxes Earlier output of received dataCode confidential fax reception If received data cannot be printedFAX Print Hold Function Settings required for fax print holdSetting Enabling fax print holdPrinting received faxes held in memory Print Hold DataPrint Advanced Transmission Methods To cancel a broadcast transmission Using Broadcast TransmissionContinue from of Basic Procedure for Sending Faxes on Enter RX StationAutomatic Transmission AT a Specified Time Setting UP a Timer TransmissionTimer Mode MondayPress the OK key Perform the desired fax operation Selected day is setYour machine Other machine PollingPolling memory Your machinePolling Using the Polling FunctionSending Options Select Sending Options with the or keySerial polling PollingAbout the steps that follow Using Polling Memory Scanning a document into polling memory the Public BoxSelect Sending Make sure that the reception mode is set to auto receptionPrinting documents in the Public Box ADDRestricting polling access polling security Deleting documents from the Public BoxYES Position of sender information Including Sender Information on FaxesExample of fax page printed out by the receiving machine Document dataPages Selecting Dual Page ScanMenu Select Dual Pages with the or keyMenu Adding a Cover SHEET/MESSAGE to a FAX TransmissionSelecting a cover sheet / message No MessageProgram Using Settings Stored AS a ProgramUsing a Program CorpConfiguring the Basic Settings Settings DescriptionAlways Print Setting Default Description Print at ErrorSelect Setting Do not Print Destination list appears Settings the DestinationClick the destination number to be set Forwarding Destination screen appearsForward Destination Max Forward ConditionSender Number Forward All, ForwardForwarding received faxes Using the Forwarding FunctionProgramming the fax number of the forwarding destination Your machineRX Data Transfer Select RX Data Transfer with the or keySelect Transfer with the or key Double-click the Setup icon When installing is finished, click the Close buttonWhen MX-NB12 is installed Standard 3333 4444 010 Communication Between Machines Supporting F-CODES0001 11245 7732123 Public BoxPasscode Creating a BOX for F-CODE TransmissionSEP SUB PWD SIDCode Polling Memory HOW F-CODE Polling Memory WorksSelect Reading Memory Polling Using F-CODE Polling MemoryScanning a document into an F-code polling memory box M-POLL OrigSelect Print or Delete with the or key Checking and clearing document data in a boxOriginal ADD Change Delete Documents are deleted from the F-code polling memory boxSUB ADD Polling Procedure for F-CODE PollingSending Options Serial Polling SUB Address TX Select SUB ADD Polling with the or keyAfter communicating with To cancel the operationEnter a passcode maximum 20 digits with the numeric keys Other machine, your machineCode Transmission F-CODE Confidential Transmission When data is printedCode Confidential Transmission Other machine Your machineSUB Address TX Code confidential transmissionSending Options Serial Polling SUB ADD PollingBOX Print ReportCONF. RX Data CorpCode Relay Broadcast Transmission Relay request machine sends documentRelay machine your machine Transmission Using F-CODES Using AN Extension Phone Using an extension phone for voice callsActivating fax transmission Setting the Reception Mode RCV. SettingManual Select Entry with the or key ProgrammingEntry Function selection menuDial RAPID/SPEEDCHANGE/DELETE Startenter Code settingsAbout the setting options OthersChain Dial Pass CodeOthers SUB Address TX Speed StartenterInternational TX Others SUB Address Chain DialOthers Chain Dial TX Speed OFFEnter search characters see Entering Characters on EnterEnter a group name see Entering Characters on Press the correct keyGroup RAPID/SPEEDChange No Delete #DETAIL SBC CODelete CHANGE/DELETEOkenter This completes the editing procedureStartset Edit the group name see Entering Characters onOn page 74, select Delete with the or key Deleting a group keySTORING, Editing and Deleting Programs ProgramEnter TX Type DetailPROGRAMMING, EDITING, and Deleting F-CODE Memory Boxes SUB ADD SettingSelect SUB ADD Setting with the or key Programming AN F-CODE Memory BOXSee steps 5 and 6 on Select an unused box - - - with the or keyEnter the print passcode 4 digits with the numeric keys See steps 3 and 4 onPress the Start key to end the procedure Programming AN F-CODE Relay GroupSelect Change or Delete with Key Public Boxes onPress the OK key Select Delete with the or key Edit the passcode maximum 20 digits with the numeric keysEdit the print passcode 4 digits with the numeric keys Editing an F-code confidential boxEditing an F-code relay group Select Change or Delete with the or keyEdit the relay destinations Deleting an F-code relay groupDeleting an F-code public box Press the OK key and then press the Back key to exitEditing an F-code public box Repeat steps 11 through 14. ToCONF. RX Data Timer List MEM. Polling List Rapid # ListReport Activity ReportChanging to Entry Mode Entering CharactersCharacters That can be Entered Character Entry Keys Character Characters and function Entry keyInitial Procedure for Entering Characters TPSEntering special characters Press the SP keyConfidential reception Always Prints /NEVER Prints Sending result ExplanationReception result Explanation When AN Alarm Sounds and a Warning Message is Displayed Message Meaning of message Solution Alarm soundsMessage display Action SELF-DIAGNOSTIC FunctionMessages During Normal Operation Message Meaning of messageProblems and Solutions Problem Check SolutionSelecting ResolutionExposure Settings RoutineAdministrator Settings List Setting nameAdministrator Settings Menu LevelMode Select Copier Printer Scanner Procedure for Using the System SettingsInitial Procedure CountList PRINT/SET List SettingFollow steps 1 through 6 of Initial Procedure List Print100 Initial SettingDial Mode Pause TimeOWN Passcode SET Speaker Volume101 TX/RX END SoundExtension TEL PBX Setting102 Distinctive Ring103 Account ControlAccount # SET 104 Auto Summer Time SettingDisable FAX Print Hold Date & Time SETSending Function 105106 Ring Timeout in Auto TX 107Recall SET ERR RCV. Function 108Duplex Reception 109Received Data Print Condition Only on models with the two-sided printing functionReceived Data FW. Station SET 110FW. RX Data Earlier Output111 Polling Passcode # ModePolling Security Enter Junk FAX #MH, MR, MMR, Jbig Specifications112 YesSymbols / Numbers Index113 114 115 Sharp Electronics Europe GmbH SHAR~
Top Page Image Contents