Sharp MX-3500N manual Pull out the right side cover, Close the right side cover

Page 33

Fusing unit pressure adjusting levers

In some cases damage to the envelopes, colour deviations, or smudging may occur even if envelopes within the specifications are used. This problem may be alleviated by shifting the fusing unit pressure adjusting levers from their "normal pressure position" to the "lower pressure position". Follow the procedure on the this page.

1

Pull out the right side cover.

While pushing up the open/close lever on the right side cover, gently open the cover.

B

A

Lower pressure position

2

Move the fusing unit pressure adjusting levers (two) to the lower pressure position as shown.

	A: Front side of	Normal	B: Rear side of
		position
	fusing unit		fusing unit

Close the right side cover.

3

Caution

The fusing unit is hot. Take care not to burn yourself when operating the fusing unit pressure adjusting levers.

Be sure to return the levers to the "normal pressure position" before printing or copying on paper other than envelopes. Otherwise, fusing problems, paper misfeeds, or equipment failure may occur.

32

Image 33

Contents Users Guide Table of Contents Manual name Contents About this ManualManuals Provided with the Machine Icons used in the manuals Exterior Part Names and FunctionsTray 4 when a stand/2 x 500 sheet paper drawer is installed Saddle stitch finisherTray Interior Automatic document feeder Document cover USB connecter B type ConnectorsLAN connecter Telephone line socketOperation Panel Power key Power Save key / indicatorMain power indicator Clear ALL keySystem Settings Administrator Keys Touch Sound Using the touch panelTouch Panel ExamplePRINT/SEND Status JOB Status Turning on the power Turning the Power on and OFFTurning off the power When using the fax or Internet fax functionsPreheat Mode Power Save KEYAuto power shut-off mode Sleep mode Energy Save FunctionsAuthentication by User Number User AuthenticationEnter your user number 5 to 8 digits With the numeric keysIf an incorrect user number is entered 3 times in a row Authentication by Login Name / Password Touch the Login Name key or the keySelect your user name Touch the Password key If you are logging in using a user selection keyWhen logging in using the Direct Entry key System Settings Administrator User Registration Important Points about Paper Names and Locations of TraysTray numbers Meaning of R in Paper Sizes Useable PaperMore information on plain paper and special paper Paper that is not recommended Paper that cannot be usedLoading Paper Tray Settings for Trays 1 toChanging the Paper Size System Settings Paper Tray Settings Set the paper size and paper typeIf you changed the paper loaded in tray 1 to tray Place the paper in the centre of the paper table Pull out traySystem Settings Paper Tray Settings Open the bypass tray Loading Paper in the Bypass Tray Touch the paper type key of the bypass tray Open the paper settings screen Select the type of paper used in the bypass tray Set the paper sizeInserting paper Important Points When Using the Bypass TrayInserting tab paper Select the bypass trayInserting transparency film Inserting envelopesExample of loading a envelope Close the right side cover Pull out the right side coverPlacing the Original Allowed original weightsPlacing Originals in the Automatic Document Feeder Make sure an original does not remainWhen the originals are the same width Adjust the original guides to the size of the originalsWhen the originals are different widths Place the originalPositions Open the automatic document feeder Place the original Placing the Original on the Document GlassClose the automatic document feeder Allowed original sizes Maximum original sizePlacing a thick book Hinges supporting the automatic document feederFeeder will rise Product name Product number Description Peripheral DevicesAR-PN1A Finisher Part NamesSupplies Replacing the staple cartridge Finisher MaintenanceReplace the staple case Removing staple jamsSlide the finisher back to the right Close the coverSlide the finisher back to the right Gently push the box back Close the cover Discarding punch waste when a punch module is installedStapler compiler Saddle Stitch FinisherStapler section Front cover Saddle stitch trayOpen the front cover Pull out the stapler section Saddle Stitch Finisher MaintenanceInsert a new staple cartridge into the staple case Push the stapler section backClose the front cover Remove any paper from the stapler compiler Remove the misfed paper Push the stapler section back Discarding punch waste when a punch module is installed Cleaning the Document Glass and Automatic Document Feeder Regular MaintenanceExamples of lines in the image MX-3501N/4501NDocument glass Automatic document feeder Black lines White linesOther models Cleaning the Main Charger of the Photoconductive Drum Cleaning the Bypass Feed RollerAs shown in Figure Release the waste toner box Cleaning the Laser UnitCleaning tool is not dirty Make sure that the cleaner at the tipPull the replacement cleaner out of the waste toner box Remove the dirty cleaner from the tip of the cleaning toolClean the laser unit Repeat to clean all holes in the laser unit 4 holesPush the waste toner box into the machine Replace the cleaning tool Replacing the Toner Cartridges Remove the protective material from the new toner cartridge Pull the toner cartridge toward youInsert the new toner cartridge horizontally Push the cartridge in until it locks securely in placeClose the front cover Replacing the Waste Toner BOX Open the front cover Release the used waste toner boxRemove the waste toner box Place the box on a flat surface Install the new waste toner boxRemove the seals around the holes Plug the holesPush the box in until it clicks into place Key Description Functions of the Main KeysSymbols key Changing the Entry ModeEntering Text from AN External Keyboard Characters keyUsers Guide

Related manuals

Manual 170 pages 14.13 Kb

Manual 61 pages 44.33 Kb

Manual 132 pages 48.37 Kb