Sharp MX-3500N manual Interior

Page 7

INTERIOR

(16)

(17)

(18)

(19)

When using the MX-3500/4500 Series

 

 

 

 

 

(22)

(23) (24)

(25)

(26)

(27)

(28)

(20) (21)

(16)Toner cartridges

When the toner in a cartridge runs out, the cartridge must be replaced with a new cartridge of the same colour. The shape of the toner cartridge varies slightly by model.

☞REPLACING THE TONER CARTRIDGES (page 60)

(17)Fusing area

Heat is applied here to fuse the transferred image onto the paper.

Caution

The fusing unit is hot. Take care not to burn yourself when removing a paper misfeed.

(18)Transfer belt

During full colour copying, the toner images of each of the four colours on each of the photoconductive drums are combined together on the transfer belt.

During black and white copying, only the black toner image is transferred onto the transfer belt.

Do not touch or damage the transfer belt.

This may cause a defective image.

(19)Right side cover

Open this cover to operate the fusing area pressure adjustment lever and to remove a misfeed.

☞Fusing unit pressure adjusting levers (page 32)

(20)Paper reversing section cover

This is used when 2-sided copying and printing is performed. Open this cover to remove a paper misfeed.

(21)Bypass tray

Use this tray to feed paper manually.

When loading paper larger than A4R or 8-1/2" x 11"R, be sure to pull out the bypass tray extension.

☞LOADING PAPER IN THE BYPASS TRAY (page 28)

(22)Main power switch

This is used to power on the machine.

When using the fax or Internet fax functions, keep this switch in the "On" position.

☞TURNING THE POWER ON AND OFF (page 13)

(23)Waste toner box

This collects excess toner that remains after copying and printing.

Your service technician will collect the waste toner box.

(24)Waste toner box release button

Press this button when you need to release the waste toner box lock to replace the waste toner box or clean the laser unit.

☞CLEANING THE LASER UNIT (page 56)

☞REPLACING THE WASTE TONER BOX (page 63)

(25)Handle

Pull this out and grasp it when moving the machine.

(26)Right cover of stand/1 x 500 sheet paper drawer Right cover of stand/2 x 500 sheet paper drawer (when a stand/1 x 500 sheet paper drawer or a stand/2 x 500 sheet paper drawer is installed) Open this to remove a paper misfeed in tray 3 or tray 4.

(27)Paper tray right side cover

Open this to remove a paper misfeed in tray 1 or tray 2.

(28)Right side cover release lever

To remove a paper jam, pull and hold this knob up to open the right side cover.

6

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Users Guide Table of Contents About this Manual Manual name ContentsManuals Provided with the Machine Icons used in the manuals Exterior Part Names and FunctionsSaddle stitch finisher Tray 4 when a stand/2 x 500 sheet paper drawer is installedTray Interior Automatic document feeder Document cover Telephone line socket ConnectorsUSB connecter B type LAN connecterOperation Panel Clear ALL key Power Save key / indicatorPower key Main power indicatorExample Using the touch panelSystem Settings Administrator Keys Touch Sound Touch PanelPRINT/SEND Status JOB Status When using the fax or Internet fax functions Turning the Power on and OFFTurning on the power Turning off the powerEnergy Save Functions Power Save KEYPreheat Mode Auto power shut-off mode Sleep modeWith the numeric keys User AuthenticationAuthentication by User Number Enter your user number 5 to 8 digitsIf an incorrect user number is entered 3 times in a row Touch the Login Name key or the key Authentication by Login Name / PasswordSelect your user name If you are logging in using a user selection key Touch the Password keyWhen logging in using the Direct Entry key System Settings Administrator User Registration Names and Locations of Trays Important Points about PaperTray numbers Useable Paper Meaning of R in Paper SizesMore information on plain paper and special paper Paper that is not recommended Paper that cannot be usedLoading Paper Tray Settings for Trays 1 toChanging the Paper Size Set the paper size and paper type System Settings Paper Tray SettingsIf you changed the paper loaded in tray 1 to tray Place the paper in the centre of the paper table Pull out traySystem Settings Paper Tray Settings Open the bypass tray Loading Paper in the Bypass TraySet the paper size Open the paper settings screenTouch the paper type key of the bypass tray Select the type of paper used in the bypass traySelect the bypass tray Important Points When Using the Bypass TrayInserting paper Inserting tab paperInserting envelopes Inserting transparency filmExample of loading a envelope Close the right side cover Pull out the right side coverMake sure an original does not remain Allowed original weightsPlacing the Original Placing Originals in the Automatic Document FeederPlace the original Adjust the original guides to the size of the originalsWhen the originals are the same width When the originals are different widthsPositions Allowed original sizes Maximum original size Placing the Original on the Document GlassOpen the automatic document feeder Place the original Close the automatic document feederHinges supporting the automatic document feeder Placing a thick bookFeeder will rise Product name Product number Description Peripheral DevicesAR-PN1A Part Names FinisherSupplies Replacing the staple cartridge Finisher MaintenanceClose the cover Removing staple jamsReplace the staple case Slide the finisher back to the rightSlide the finisher back to the right Gently push the box back Close the cover Discarding punch waste when a punch module is installedFront cover Saddle stitch tray Saddle Stitch FinisherStapler compiler Stapler sectionOpen the front cover Pull out the stapler section Saddle Stitch Finisher MaintenancePush the stapler section back Insert a new staple cartridge into the staple caseClose the front cover Remove any paper from the stapler compiler Remove the misfed paper Push the stapler section back Discarding punch waste when a punch module is installed Cleaning the Document Glass and Automatic Document Feeder Regular MaintenanceBlack lines White lines MX-3501N/4501NExamples of lines in the image Document glass Automatic document feederOther models Cleaning the Bypass Feed Roller Cleaning the Main Charger of the Photoconductive DrumAs shown in Figure Release the waste toner box Cleaning the Laser UnitRemove the dirty cleaner from the tip of the cleaning tool Make sure that the cleaner at the tipCleaning tool is not dirty Pull the replacement cleaner out of the waste toner boxRepeat to clean all holes in the laser unit 4 holes Clean the laser unitPush the waste toner box into the machine Replace the cleaning tool Replacing the Toner Cartridges Push the cartridge in until it locks securely in place Pull the toner cartridge toward youRemove the protective material from the new toner cartridge Insert the new toner cartridge horizontallyClose the front cover Open the front cover Release the used waste toner box Replacing the Waste Toner BOXRemove the waste toner box Plug the holes Install the new waste toner boxPlace the box on a flat surface Remove the seals around the holesPush the box in until it clicks into place Key Description Functions of the Main KeysCharacters key Changing the Entry ModeSymbols key Entering Text from AN External KeyboardUsers Guide
Related manuals
Manual 170 pages 14.13 Kb Manual 61 pages 44.33 Kb Manual 132 pages 48.37 Kb
Top Page Image Contents