Sharp XE-A212 Replacing the Batteries, Replacing the Paper Roll, Paper specification

Page 76

A212_5 OPERATOR MAINTENANCE 03.7.5 7:53 AM Page 74

4Replacing the Batteries

This cash register displays a low battery warning message “LOW BATTERY” when the batteries are low, and displays a no battery warning message “NO BATTERY” when batteries are extremely low or batteries are not installed.

When the low battery message is displayed, replace the batteries with new ones as soon as possible. The existing batteries will be dead in about two days.

When the no battery message is displayed, replace the batteries immediately. Otherwise, if the AC power cord is disconnected or a power failure occurs, all the programmed settings will be reset to the default settings and any data stored in memory will be cleared.

Be sure to observe precautions shown on page 1 when handling batteries.

To replace the batteries:

1.Make sure that the cash register is plugged in.

2.Turn the mode switch to the REG position.

3. Remove the printer cover.

4.Open the battery compartment cover next to the paper roll cradle and

remove the old batteries.

5.Install three new R6 or LR6 batteries (“AA” size) in the battery compartment. Be sure the positive and negative poles of each battery are facing in the proper direction. When they are installed correctly, the “LOW BATTERY” or “NO BATTERY” will disappear.

6.Close the battery compartment cover.

7.Replace the printer cover.

5Replacing the Paper Roll

Be sure to use paper rolls specified by SHARP.

The use of any other paper rolls other than those specified could cause paper jamming, resulting in register malfunction.

Paper specification

Paper width: 57.5 ± 0.5 mm

Max. outside diameter: 80 mm

Quality: Thermal paper

• Be sure to set the paper roll prior to using your machine, otherwise it may cause a malfunction.

Install the paper roll in the printer. Be careful to set the roll correctly.

(How to set the paper roll)

To the printer

To the printer

CorrectIncorrect

74

Image 76

Contents XE-A212 Aviso Introduction U T I O NFor Easy Set-up, see Getting Started Never operate the register with wet handsContents Correction After Finalizing a Transaction Void mode Basic Function Programming For Quick StartExternal View Front view Parts and Their FunctionsPrinter Mode Switch and Mode Keys KeyboardKeyboard layout Key namesKeyboard sheet Customer display Pop-up type Displays Operator displayDrawer Lock Key How to remove the register from the fixing angle bracket How to install the fixing angle bracketGetting Started Initializing the cash register Be careful with the paper cutter, so as not to cut yourselfInstalling a paper roll When using the take-up spool using as journal paper When not using the take-up spool using as receipt paperDate Time VAT/tax Decimal point position tab setting for domestic currency Rounding systemBasic Sales Entry Basic Sales Entry Example1500 2300Error Warning When using the department keys for department 1 to When using the department code entry keyItem Entries Single item entries PLU entriesRepeat entries $ $Multiplication entries @ $ Single item cash sale Sics entryPLU level shift for direct PLU key @ 50 d 1500 d @ 41 d @ 80 p @ 500 ﬁ @ 85 p 1200 pAutomatic return mode Lock shift mode300 Displaying SubtotalsFinalization of Transaction Cash or cheque tendering Cash or cheque sale that does not require tender entry950 a b Credit saleMixed-tender sale Computation of VAT Value Added Tax/tax VAT/ tax systemOptional Features 10 %Auxiliary Entries Percent calculations premium or discount Automatic VAT 1 and automatic tax 2-4 system800 5 % 575 100Deduction entries Refund entries250 f 41 fd 100 d 85 fp 150 p Non-add code number entries and printingGuest Look-up GLU 1230 N 150011 G a 11 G1400 1600 Auxiliary Payment Treatment Currency exchange 4650 d10000 a 2300 4650 dReceived-on account entries Paid-out entriesNo sale exchange Automatic Sequence Key a key Entries328 ª CorrectionCorrection of the Last Entry direct void Subtotal Void 1310 1755Prior to Programming Procedure for programmingGuidance messages 10 d 29 @200 Guidance for text programming Using character keys Keys on the shaded areaOperator display Example Hijk01 231 Alphanumeric character code tableBasic Function Programming Date and Time ProgrammingTime Tax ProgrammingTax rate programming 12 sKey operation example Print Department Programming Auxiliary Function ProgrammingDepartment status Preset unit price PLU Price Look-Up and Subdepartment ProgrammingDirect PLU key programming For PLU code 1 to Abcdefgh 00011183 @Specify the direct PLU key and its level Key operation Operator displayAssociated dept. programming Press sto skip Unit price and associated department assignmentFunction programming Press sto skip 200 p 125 # PLU/subdepartment selectionMiscellaneous Key Programming Rate for %10 P 25 % Amount forPercent rate limitation for % Function parameters for %Function parameters for Function parameters for r, o, X, Y, c, b and a1006 @ 102 @Department text item label 16 digits Text Programming018 @ PLU text item label 16 digits Function text 12 digitsFruit s Apple sList of function texts NET2David s Clerk names 12 digitsLogo message print format 3 types Foreign currency symbol 4 digits Domestic currency symbol 4 digitsS s a US S $Training mode text 12 digits Advanced Function ProgrammingRegister Number and Consecutive Number Programming Register numberVarious Function Selection Programming Function selection for miscellaneous keys00000100 s a Job code Selection EntryReceipt print format Print formatPrinting style PLU level shift and GLU function parameters Other programmingJob code Selection Entry Compression print on journal A2123 for the Manager 03.9.8 457 PM Action when EJ memory area is full PGM mode operation records typeTemporary EJ printing during a transaction Power save mode Logo message print format10 @ 0060 s a 11 @Language selection Thermal printer densityEJ memory type Training clerk specification for training mode Auto key programming Automatic sequence key86 @ 20 s a 100Euro system settings Automatic Euro modification operation settings01 s Euro ProgrammingDate setting for Euro modification operation Time setting for Euro modification operation13 @ 01072005 s 14 @ 10 sReading Stored Programs Key sequence for reading stored programSample printouts Programming reportProgramming report Department programming report PLU programming reportAuto key programming report Printer density programming reportTraining Mode Reading X and Resetting Z of Sales Totals Summary of Reading X and Resetting Z ReportsDaily Sales Totals Full sales report Sample reportIndividual clerk report PLU report by designated rangeFull clerk report Hourly report Open GLU reportOpen GLU report by clerk Balance report Periodic Consolidation Full sales reportEJ Report Reading and Resetting Printing journal data on the way of a transactionSample print Sample EJ reportOverride Entries Incorrect receipt Cancellation receipt250 Euro Migration Function PeriodItems Euro statusOptional Programming for the Introduction of Euro Currency exchange rateExchange rate entry selection Cheque/credit operationCase of Power Failure Operator MaintenanceCase of Printer Error Paper specification How to set the paper rollReplacing the Batteries Replacing the Paper RollRemoving the paper roll Installing the receipt paper roll Installing the paper rollInstalling the journal paper roll Cleaning the Printer Print Head / Sensor / Roller Removing a Paper JamRemoving the Till and the Drawer Opening the Drawer by HandBLUENeutral BROWNLive Environment ProtectionUmweltschutz Protection de l’environnementSharp Corporation