MicroNet Technology SP5001/S user manual 12V DC Port, Back Panel Connections

Page 13

12V DC Port:

DC Power supply.

1.5.3Back Panel Connections

This section outlines how to connect your SP5001/S to the LAN and the WAN. In the case of connecting a Cable Modem you must connect the coaxial cable from your cable service to the threaded coaxial cable connect on the back of the cable modem.

Step 1. Connecting the Console Port

For the initial configuration of your SP5001/S, you need to use terminal emulator software on a workstation and connect it to the console port of SP5001/S. Connect the 9-pin end of the console cable to the console port of SP5001/S and the other end to a serial port (COM1, COM2 or other COM port) of your workstation. You can use an extension RS-232 cable if the enclosed one is too short. After the initial setup, you can modify the configuration remotely through telnet connections.

Step 2. Connecting SP5001/S to WAN

Connect the WAN port (silver) on SP5001/S to the Ethernet port on the cable modem using the cable that came with your cable modem. The Ethernet port on the cable modem is sometimes labeled “PC” or “Workstation”.

Step 3. Connecting PC to LAN

If you have more than one PC, you must use an external hub. Connect the 10/100M LAN Port (gold) on SP5001/S to a port on the hub using a straight through Ethernet cable. If you only have one PC, you can connect SP5001/S to the PC directly without a hub. For a single PC, connect the 10/100M LAN port on SP5001/S to the Network Adapter on the PC using a crossover cable (red tag).

Step 4. Connecting the Power Adapter to your SP5001/S

Connect the power adapter to the port labeled POWER on the rear panel of SP5001/S.

Caution: To prevent damage to SP5001/S, first make sure you have the correct AC power adapter. Please see the Appendices for AC power adapter specifications for your region.

12

Image 13
Contents IP Telephony Gateway Table of Contents Voice Setting Screen List of Figures Change password Screen List of Tables About this User’s Manual Key Features Features of SP5001/SAudio feature SP5001/S OverviewRemote Firmware Upgrade Default SettingsTelnet and Web Login Password SecurityBack Panel Front Panels1 SP5001/S LEDs SP5001/S LEDs Descriptions Hardware SpecificationsCOM Port Back Panel Port Ethernet PortTEL Port Back Panel Connections 12V DC PortSetting Up the TCP/IP Protocol Additional Installation RequirementsPower Up Your SP5001/S Accessing the Web Configuration Web Configuration with FXS IntroductionWelcome Screen Navigation Panel Links SP5001/S web configuration welcome screenNavigating the Web Configuration Saving Your ConfigurationGeneral Configuration Initial ConfigurationStatic IP address Commit Data Dhcp mode One Sets SP5001/S IP Sharing ConfigurationEnable the IP sharing function Two sets attached to IP Sharing Device Router See following for example Page Making a VoIP Call Configure the gateway into the Peer-to-Peer modePhone Book On table will display on the first index Configure the Proxy Infomation Configure the gateway into the Proxy routed modeUpdate Application Version Upgrade ROM VersionBefore you start downloading ROM File Upgrade OK Page Network Interface Screen H323 ConfigurationGMT SIP Information SIP Information ScreenSystem Configuration System Configuration ScreenVoice Configuration Voice Setting ScreenBecause this might cause incompatibility Phone Pattern Screen Phone Pattern ConfigurationSupport Function Screen Support ConfigurationPhone Book Screen Label Description Dscp Configuration Dscp Configuration ScreenPassword Password ScreenROM Upgrade Screen Flash Clean Screen Commit Data Screen Reboot System Screen Hyper Terminal Setting Command ListConnect To Initial Screen Initial Screen Entering LoginSet Password Command Structure in SP5001/SCommand Structure in SP5001/S Set up IP AddressSaving Your Configuration Application Mode ConfigurationProxy mode Application modesUsr/config$ security -line 1 -name 12345 -password Peer-to-Peer Mode Behind IP-Sharing Mode One Set of SP5001/S DMZ Two Sets of SP5001/S UDP PPPoE Mode Upgrade steps How to upgradeBefore you start downloading Usr/config$ rom -hwver Commands in SP5001/S Commands in SP5001/SQuit System Commands OverviewParameter Usages Flash Flash command listCommit Commit command list IfaddrIfaddr -print command list Time Time command list PingPbook Phone book command listPhoneBook Rules Pppoe Pppoe command listSysconf System information command listSysconf -print command list 19.7.12 sip Sip command listSip -print command list Security Command List Voice Voice command listParameters because this might cause incompatibility Voice -print command list Support Support -print command list 19.7.16 tos Phone Phone command listPhone -print rbt command list 19.7.18 rom Rom command listRom -print command list Passwd