MicroNet Technology user manual Two Sets of SP5001/S

Page 59

Two Sets of SP5001/S

1.The WAN IP Address obtained from ADSL has two kinds of methods. One is fixed IP Address, while user applies for one or more fixed IP Addresses. Another is dynamic IP Address while user applies for dial-up connection way.

2.The LAN IP Address of User’s PC can be set as DHCP client in order to gain a valid one.

3.Assign an IP address to each set using DHCP or fixed address.

4.Enable the IP Sharing function for each set using following command.

Fixed IP Address

usr/config$ ifaddr –ipsharing 1 210.11.22.33

5.Configure separate SIP port and RTP port for each set to prevent from port conflict. For example, if set A uses the default settings (SIP port: 5060, RTP port: 16384), you must change set B’s setting to SIP port equal to 5061 and RTP port equal to 26384 for instance.

Change SIP port – usr/config$sip –port 5061

Change RTP port – usr/config$sip –rtp 26384

6.Use the Port Forwarding or Port Redirection function provided by IP Sharing device (Router). See the following for example.

58

Image 59

Contents IP Telephony Gateway Table of Contents Voice Setting Screen List of Figures Change password Screen List of Tables About this User’s Manual SP5001/S Overview Features of SP5001/SKey Features Audio featureSecurity Default SettingsRemote Firmware Upgrade Telnet and Web Login PasswordBack Panel Front Panels1 SP5001/S LEDs SP5001/S LEDs Descriptions Hardware SpecificationsTEL Port Back Panel Port Ethernet PortCOM Port Back Panel Connections 12V DC PortSetting Up the TCP/IP Protocol Additional Installation RequirementsPower Up Your SP5001/S Welcome Screen Web Configuration with FXS IntroductionAccessing the Web Configuration Navigation Panel Links SP5001/S web configuration welcome screenNavigating the Web Configuration Saving Your ConfigurationStatic IP address Initial ConfigurationGeneral Configuration Commit Data Dhcp mode One Sets SP5001/S IP Sharing ConfigurationEnable the IP sharing function Two sets attached to IP Sharing Device Router See following for example Page Making a VoIP Call Configure the gateway into the Peer-to-Peer modePhone Book On table will display on the first index Configure the Proxy Infomation Configure the gateway into the Proxy routed modeBefore you start downloading Upgrade ROM VersionUpdate Application Version ROM File Upgrade OK Page Network Interface Screen H323 ConfigurationGMT SIP Information SIP Information ScreenSystem Configuration System Configuration ScreenVoice Configuration Voice Setting ScreenBecause this might cause incompatibility Phone Pattern Screen Phone Pattern ConfigurationSupport Function Screen Support ConfigurationPhone Book Screen Label Description Dscp Configuration Dscp Configuration ScreenPassword Password ScreenROM Upgrade Screen Flash Clean Screen Commit Data Screen Reboot System Screen Hyper Terminal Setting Command ListConnect To Initial Screen Initial Screen Entering LoginSet up IP Address Command Structure in SP5001/SSet Password Command Structure in SP5001/SApplication modes Application Mode ConfigurationSaving Your Configuration Proxy modeUsr/config$ security -line 1 -name 12345 -password Peer-to-Peer Mode Behind IP-Sharing Mode One Set of SP5001/S DMZ Two Sets of SP5001/S UDP PPPoE Mode Before you start downloading How to upgradeUpgrade steps Usr/config$ rom -hwver Commands in SP5001/S Commands in SP5001/SQuit System Commands OverviewParameter Usages Flash Flash command listCommit Commit command list IfaddrIfaddr -print command list Time Time command list PingPbook Phone book command listPhoneBook Rules Pppoe Pppoe command listSysconf System information command listSysconf -print command list 19.7.12 sip Sip command listSip -print command list Security Command List Voice Voice command listParameters because this might cause incompatibility Voice -print command list Support Support -print command list 19.7.16 tos Phone Phone command listPhone -print rbt command list 19.7.18 rom Rom command listRom -print command list Passwd