MicroNet Technology SP5001/S user manual Voice command list

Page 79

19.7.14 [voice]

The voice command is associated with the audio setting information.

There are four voice codecs supported by SP5001/S.

usr/config$ voice

Voice codec setting information and configuration Usage:

voice [-send [G723 ms] [G711U ms] [G711A ms] [G729 ms] ] [-volume [voice level] [input level] [dtmf level]] [-nscng [G711U used1] [G711A used2] [G723 used3]] [-echo used] [-mindelay t1] [-maxdelay t2] [-optfactor f]

voice -print

voice -priority [G723] [G711U] [G711A] [G729]

-print

 

Display voice codec information and configuration.

-send

 

Specify sending packet size.

 

 

G.723

(30/60 ms)

 

 

G.711U (20/40/60 ms)

 

 

G.711A (20/40/60 ms)

 

 

G.729

(20/40/60 ms)

-priority

Priority preference of installed codecs.

 

 

G.723

 

 

 

G.711U

 

 

 

G.711A

 

 

 

G.729

 

-volume

 

Specify the following levels:

 

 

voice volume (0~63, default: 25),

 

 

input gain (0~38, default: 25),

 

 

dtmf

volume (0~31, default: 23),

-nscng

 

No sound compression and CNG. (G.723.1 only, On=1,

Off=0).

 

 

 

-echo

Setting of echo canceller. (On=1, Off=0, per port basis).

-mindelay

 

Setting of j itter buffer min delay. (0~150, default: 90).

-maxdelay

Setting of jitter buffer max delay. (0~150, default:

150).

 

 

 

Example:

 

 

 

voice -send g723 60 g711u 60 g711a 60 g729 60 voice -volume voice 20 input 32 dtmf 27 voice -echo 1

usr/config$

Figure 58. voice command list

Parameter Usages:

-print

print current voice information and configurations.

-send

to define packet size for each codec. 20/40/60ms means to

 

send a voice packet per 20/40/60 milliseconds. The smaller the

 

packet size, the shorter the delay time. If network is in good

 

condition, smaller sending packet size is recommanded. In this

 

 

78

Image 79
Contents IP Telephony Gateway Table of Contents Voice Setting Screen List of Figures Change password Screen List of Tables About this User’s Manual SP5001/S Overview Features of SP5001/SKey Features Audio featureSecurity Default SettingsRemote Firmware Upgrade Telnet and Web Login PasswordBack Panel Front Panels1 SP5001/S LEDs SP5001/S LEDs Descriptions Hardware SpecificationsCOM Port Back Panel Port Ethernet PortTEL Port Back Panel Connections 12V DC PortSetting Up the TCP/IP Protocol Additional Installation RequirementsPower Up Your SP5001/S Accessing the Web Configuration Web Configuration with FXS IntroductionWelcome Screen Navigation Panel Links SP5001/S web configuration welcome screenNavigating the Web Configuration Saving Your ConfigurationGeneral Configuration Initial ConfigurationStatic IP address Commit Data Dhcp mode One Sets SP5001/S IP Sharing ConfigurationEnable the IP sharing function Two sets attached to IP Sharing Device Router See following for example Page Making a VoIP Call Configure the gateway into the Peer-to-Peer modePhone Book On table will display on the first index Configure the Proxy Infomation Configure the gateway into the Proxy routed modeUpdate Application Version Upgrade ROM VersionBefore you start downloading ROM File Upgrade OK Page Network Interface Screen H323 ConfigurationGMT SIP Information SIP Information ScreenSystem Configuration System Configuration ScreenVoice Configuration Voice Setting ScreenBecause this might cause incompatibility Phone Pattern Screen Phone Pattern ConfigurationSupport Function Screen Support ConfigurationPhone Book Screen Label Description Dscp Configuration Dscp Configuration ScreenPassword Password ScreenROM Upgrade Screen Flash Clean Screen Commit Data Screen Reboot System Screen Hyper Terminal Setting Command ListConnect To Initial Screen Initial Screen Entering LoginSet up IP Address Command Structure in SP5001/SSet Password Command Structure in SP5001/SApplication modes Application Mode ConfigurationSaving Your Configuration Proxy modeUsr/config$ security -line 1 -name 12345 -password Peer-to-Peer Mode Behind IP-Sharing Mode One Set of SP5001/S DMZ Two Sets of SP5001/S UDP PPPoE Mode Upgrade steps How to upgradeBefore you start downloading Usr/config$ rom -hwver Commands in SP5001/S Commands in SP5001/SQuit System Commands OverviewParameter Usages Flash Flash command listCommit Commit command list IfaddrIfaddr -print command list Time Time command list PingPbook Phone book command listPhoneBook Rules Pppoe Pppoe command listSysconf System information command listSysconf -print command list 19.7.12 sip Sip command listSip -print command list Security Command List Voice Voice command listParameters because this might cause incompatibility Voice -print command list Support Support -print command list 19.7.16 tos Phone Phone command listPhone -print rbt command list 19.7.18 rom Rom command listRom -print command list Passwd