MicroNet Technology user manual Power Up Your SP5001/S

Page 15

Step 3. Click whether the TCP/IP Protocol has already been installed onto your computer’s Ethernet card. Note that TCP/IP Protocol can be installed for a computer’s Dial-Up Adapter as well as for the Ethernet card.

-If yes, go to set 7.

-If no, click the “Add” button

Step 4. Double-click “Protocol” in the Select Network Component Type or highlight “Protocol” then click “Add”.

Step 5. Highlight “Microsoft” under the list of manufacturers.

Step 6. After a new second, you will be returned to the Network window. The TCP/IP Protocol should now be on the list of installed network components.

Step 7. Click the “Properties” button. The TCP/IP Properties windows consist of several tabs. Choose the “IP Address” tab.

Step 8. Select “Specify an IP Address” and enter “10.1.1.1” in the “IP Address” location (where xxx is a number between 2 and 254 used by SP5001/S to identify each computer), and the default “Subnet Mask”255.0.0.0”. Note than no two computers on the same LAN can have the same IP address.

Step 9. Click on the “DNS Configuration” tab and select “Enable DNS”. Then click the “Add” button.

Step 10. Click on the “Gateway” tab and enter the default gateway value 10.1.1.254 in the “new gateway” field, then click “Add” Button.

Step 11. Click “OK”. Restart your PC to complete the TCP/IP installation.

1.8Power Up Your SP5001/S

At this point, you should have connected the console port, the LAN Port, the WAN port and the power port to the appropriate devices or lines. Plug the power adapter into a wall outlet. The Power LED should be on. The Status LED will come on after the system tests are complete. The WAN LED and one of the LAN LEDs come on immediately after the Status LED come on, if connections have been made to the LAN and WAN ports.

14

Image 15
Contents IP Telephony Gateway Table of Contents Voice Setting Screen List of Figures Change password Screen List of Tables About this User’s Manual SP5001/S Overview Features of SP5001/SKey Features Audio featureSecurity Default SettingsRemote Firmware Upgrade Telnet and Web Login PasswordBack Panel Front Panels1 SP5001/S LEDs SP5001/S LEDs Descriptions Hardware SpecificationsBack Panel Port Ethernet Port COM PortTEL Port Back Panel Connections 12V DC PortSetting Up the TCP/IP Protocol Additional Installation RequirementsPower Up Your SP5001/S Web Configuration with FXS Introduction Accessing the Web ConfigurationWelcome Screen Navigation Panel Links SP5001/S web configuration welcome screenNavigating the Web Configuration Saving Your ConfigurationInitial Configuration General ConfigurationStatic IP address Commit Data Dhcp mode One Sets SP5001/S IP Sharing ConfigurationEnable the IP sharing function Two sets attached to IP Sharing Device Router See following for example Page Making a VoIP Call Configure the gateway into the Peer-to-Peer modePhone Book On table will display on the first index Configure the Proxy Infomation Configure the gateway into the Proxy routed modeUpgrade ROM Version Update Application VersionBefore you start downloading ROM File Upgrade OK Page Network Interface Screen H323 ConfigurationGMT SIP Information SIP Information ScreenSystem Configuration System Configuration ScreenVoice Configuration Voice Setting ScreenBecause this might cause incompatibility Phone Pattern Screen Phone Pattern ConfigurationSupport Function Screen Support ConfigurationPhone Book Screen Label Description Dscp Configuration Dscp Configuration ScreenPassword Password ScreenROM Upgrade Screen Flash Clean Screen Commit Data Screen Reboot System Screen Hyper Terminal Setting Command ListConnect To Initial Screen Initial Screen Entering LoginSet up IP Address Command Structure in SP5001/SSet Password Command Structure in SP5001/SApplication modes Application Mode ConfigurationSaving Your Configuration Proxy modeUsr/config$ security -line 1 -name 12345 -password Peer-to-Peer Mode Behind IP-Sharing Mode One Set of SP5001/S DMZ Two Sets of SP5001/S UDP PPPoE Mode How to upgrade Upgrade stepsBefore you start downloading Usr/config$ rom -hwver Commands in SP5001/S Commands in SP5001/SQuit System Commands OverviewParameter Usages Flash Flash command listCommit Commit command list IfaddrIfaddr -print command list Time Time command list PingPbook Phone book command listPhoneBook Rules Pppoe Pppoe command listSysconf System information command listSysconf -print command list 19.7.12 sip Sip command listSip -print command list Security Command List Voice Voice command listParameters because this might cause incompatibility Voice -print command list Support Support -print command list 19.7.16 tos Phone Phone command listPhone -print rbt command list 19.7.18 rom Rom command listRom -print command list Passwd