MicroNet Technology SP5001/S user manual System Commands Overview, Quit

Page 65

19.7System Commands Overview

19.7.1[quit]

Type quit will quit configuration mode. And turn back to login prompt.

usr/config$ quit

Disconnecting...

login: root

Welcome to Terminal Configuration Mode Please enter your configuration item

Figure 37. quit command list

Note: It is recommanded that type the “quit” command before you leave the console. If so, SP5001/S will ask password again when next user connects to console port.

19.7.2[debug]

Open debug message will show up specific information while Gateway is in operation. After executing the debug command, it should execute command debug -open as well. One example is demonstrated below.

usr/config$ debug

Debug message information and configuration Usage:

debug [-add type1 [[type2]...]] -open -close -status

-status	Display the enabled debug flags.
-add	Add debug flag.
-delete	Remove specified debug flag.
-open	Start to show debug messages.
-close	Stop showing debug messages.
Example:

debug -add sip msg debug -open

usr/config$

Figure 38. debug command list

In this example, user open debug flags including sip, msg.

usr/config$ debug -add sip msg usr/config$ debug –open

64

Image 65

Contents IP Telephony Gateway Table of Contents Voice Setting Screen List of Figures Change password Screen List of Tables About this User’s Manual Key Features Features of SP5001/SAudio feature SP5001/S OverviewRemote Firmware Upgrade Default SettingsTelnet and Web Login Password SecurityBack Panel Front Panels1 SP5001/S LEDs SP5001/S LEDs Descriptions Hardware SpecificationsTEL Port Back Panel Port Ethernet PortCOM Port Back Panel Connections 12V DC PortSetting Up the TCP/IP Protocol Additional Installation RequirementsPower Up Your SP5001/S Welcome Screen Web Configuration with FXS IntroductionAccessing the Web Configuration Navigation Panel Links SP5001/S web configuration welcome screenNavigating the Web Configuration Saving Your ConfigurationStatic IP address Initial ConfigurationGeneral Configuration Commit Data Dhcp mode One Sets SP5001/S IP Sharing ConfigurationEnable the IP sharing function Two sets attached to IP Sharing Device Router See following for example Page Making a VoIP Call Configure the gateway into the Peer-to-Peer modePhone Book On table will display on the first index Configure the Proxy Infomation Configure the gateway into the Proxy routed modeBefore you start downloading Upgrade ROM VersionUpdate Application Version ROM File Upgrade OK Page Network Interface Screen H323 ConfigurationGMT SIP Information SIP Information ScreenSystem Configuration System Configuration ScreenVoice Configuration Voice Setting ScreenBecause this might cause incompatibility Phone Pattern Screen Phone Pattern ConfigurationSupport Function Screen Support ConfigurationPhone Book Screen Label Description Dscp Configuration Dscp Configuration ScreenPassword Password ScreenROM Upgrade Screen Flash Clean Screen Commit Data Screen Reboot System Screen Hyper Terminal Setting Command ListConnect To Initial Screen Initial Screen Entering LoginSet Password Command Structure in SP5001/SCommand Structure in SP5001/S Set up IP AddressSaving Your Configuration Application Mode ConfigurationProxy mode Application modesUsr/config$ security -line 1 -name 12345 -password Peer-to-Peer Mode Behind IP-Sharing Mode One Set of SP5001/S DMZ Two Sets of SP5001/S UDP PPPoE Mode Before you start downloading How to upgradeUpgrade steps Usr/config$ rom -hwver Commands in SP5001/S Commands in SP5001/SQuit System Commands OverviewParameter Usages Flash Flash command listCommit Commit command list IfaddrIfaddr -print command list Time Time command list PingPbook Phone book command listPhoneBook Rules Pppoe Pppoe command listSysconf System information command listSysconf -print command list 19.7.12 sip Sip command listSip -print command list Security Command List Voice Voice command listParameters because this might cause incompatibility Voice -print command list Support Support -print command list 19.7.16 tos Phone Phone command listPhone -print rbt command list 19.7.18 rom Rom command listRom -print command list Passwd