Liebert Mechanical Considerations, Positioning the Liebert XDP, Liebert XDP dimensions

Page 11

Product Description

1.4Mechanical Considerations

1.4.1Positioning the Liebert XDP

Install the Liebert XDP according to the site specific documentation and secure the unit to the floor.

The Liebert XDP can be installed near a wall or another Liebert XDP. However, there must be at least 3 feet (92cm) clearance in front of the Liebert XDP as service access for components in the unit.

For additional technical information, refer to the System Design and Configuration Document for the Liebert XD™ System, SL-16655. The document is available in electronic format at Liebert’s Web site, www.liebert.com, as well as from your local Emerson Network Power representative.

Figure 8 Dimensions

A B

Overall Overall

C

Side Panel

ED

78"
(1981mm)	1" (25mm)

5-1/2"

(140mm)

11" (279mm)

Floor Cutout Dimensions

D

Unit Base

E

Unit Base

Unit Dimensional Data

Table 1 Liebert XDP dimensions

The shaded area indicates a recommended clearance of 36" (914mm) for component access.

DPN000767 Pg. 2, Rev. 6

Model		Dimensional Data inches (mm)				Shipping Weight, lb (kg)
Model
50/60Hz	A	B*	C	D	E	Domestic	Export

XDP160	38 (965)	34 (864)	33-1/8 (841)	33 (838)	36 (914)	990 (449)	1067 (484)

* The dimension does not include the bezel of the disconnect switch.

5

Image 11

Contents Liebert XDP Pumping Place holder Revision Unit Redundancy Level Liebert General Safety GuidelinesExample XDP160A Fluorinated Greenhouse Gas Requirements-European UnionTable of Contents Specifications Alarm Descriptions and SolutionsFigures Page Product/System Description General Product InformationEquipment Inspection Product DescriptionRemoval from Skid Equipment HandlingHandling With Skid Liebert XDP strapped to piano jack Removing pallet boards for piano jack insertionSlide this runner away From the Liebert XDP Removing Piano JacksPositioning the Liebert XDP Liebert XDP dimensionsMechanical Considerations Model Pipe Connection Point 50/60 Hz Unit piping outlet connection sizes, inches, OD CuElectrical Information High Voltage Connections Connecting High-Voltage CablesElectrical enclosure knockout locations for field wiring High voltage connections-50Hz Extra Low Voltage ELV ConnectionsField Connections-Optional for All Units Field Connections-All UnitsRecommended Pipe Size European Union Fluorinated Greenhouse Gas RequirementsConnection Sizes PipingBypass flow controllers for a Liebert XDP-based system Piping Installation MethodLiebert XDP Interconnection with Liebert XD Cooling Modules Bypass Flow ControllerBypass flow controller arrangement Bypass flow controller details, dimensionsEvacuation and Leak Check Piping Installation MethodPiping Details-Shut-Off/Isolation Valves Piping MainsChecklist for Proper Installation Indicator Lights Description Green Red Checklist for Liebert XDP StartupLiebert XDP pump light indicator-208V and 400V units System R-134a liquid level Filling the Pumped Circuit-R-134aReturn Line Diameter System refrigerant charge for the supply and return mainsReturn Line Diameter 5/8 Total 293 Calculating Refrigerant Charge-ExampleCalculating refrigerant charge-example Worksheet to calculate refrigerant chargeUser interface keypad functions Feature OverviewMicroprocessor Control DisplayMain Menu Feature OverviewViewing or Changing Settings ControlsMIN Temp SP Active AlarmsAlarm History SetpointsPump Start TD Setup OperationRestart Time Delay DegreesLead Pump Liebert XDP DIP switches and factory settingsPump Wait TD Pump OFF TDValve Time Password Security-SETPT Password and Service PasswordChange Password-SETPT Password COM Alarm Enable Change Password-SERVICE PasswordAlarm Enable Alarm Time DelayCustom Text Custom AlarmsDiagnostics Alarm Descriptions and Solutions Alarm DescriptionsEnable or Disable Alarms Red and Green Lamp IndicatorsAlter Alarm Settings System Shutdown Causes Troubleshooting the XDP TroubleshootingFluorinated Greenhouse Gas Requirements MaintenanceLiebert XDP160 specifications SpecificationsThat Ne tIti Ti n