Liebert XDP user manual Setup Operation, Restart Time Delay, Degrees, Pump Start TD

Page 29

Microprocessor Control

4.3.6TIME

To change the time, press ENTER to select the function, then use the Up or Down arrow key to change the first character, press ENTER to store, then press the Up or Down arrow key to change the second character, press ENTER to store, etc.

NOTE

The clock uses the 24-hour system (for example, 17:00 would be 5:00 PM). The date and time are kept current even when the control board is not powered.

4.3.7DATE

To change the date, press ENTER, then use the Up or Down arrow key to change the first character, press ENTER to store, press the Up or Down arrow key to change the second character, etc.

4.3.8SETUP OPERATION

NOTE

None of these setpoints should be changed before consulting an Emerson Network Power representative. Changing any of these setpoints could drastically affect the system.

Selecting Setpoint/Setup from the Main Menu will display the following selections:

Table 14 Setup operation functions default values and allowable ranges.

Menu Item

Function

Default

Range

 

 

 

 

RESTART

Restart time delay

0.1 min

0 to 9.9 min

(0 = manual restart)

 

 

 

C/F DEGREES

Celsius or Fahrenheit

F

C or F

 

 

 

 

PUMP START TD

Pump start time delay

10 sec

3 - 120 sec

 

 

 

 

PUMP WAIT TD

Pump wait time delay

10 sec

3 - 120 sec

 

 

 

 

PUMP OFF TD

Pump off time delay

5 sec

5 - 120 sec

 

 

 

 

LEAD PUMP

Lead Pump

Pump 1

Pump 1 / Pump 2

 

 

 

 

DIPSWCH

DIP switch status

NA

NA

 

 

 

 

VALVE TIME

Control valve travel time

60 sec

50 - 250 sec

 

 

 

 

Use the Up and Down arrow keys to scroll through the submenu, then press the ENTER button to access a function. To make changes or review the current setting, see 4.3.1 - Viewing or Changing Settings.

NOTE

Setpoints and system setup parameters are kept in non-volatile memory.

RESTART TIME DELAY

This function specifies the time for the unit to restart after main power is restored to the unit. If sev- eral systems are operating, the time delays should be set to different values to cause a sequential start. Delay can be set from 0.1 minutes (6 seconds) to 9.9 minutes. Setting the value to “NO!” will prevent the unit from restarting when power is restored. In this case, the unit must be restarted man- ually by pressing the “On/Off” key.

To make changes or review the current setting, see 4.3.1 - Viewing or Changing Settings.

C/F DEGREES

The control can be selected to show readings and setpoints in either degrees Fahrenheit (F) or Celsius (C). To make changes or review the setting, see 4.3.1 - Viewing or Changing Settings.

PUMP START TD

The user may set a pump start time delay (in seconds) to ensure that refrigerant begins flowing when the pump starts. If refrigerant does not begin flowing before this delay expires, the pump will stop for a period that the user may also specify (see PUMP OFF TD). After this delay, the pump will again begin its startup sequence.

To make changes or review the current setting, see 4.3.1 - Viewing or Changing Settings.

23

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Liebert XDP Example XDP160A General Safety GuidelinesFluorinated Greenhouse Gas Requirements-European Union Pumping Place holder Revision Unit Redundancy Level LiebertTable of Contents Specifications Alarm Descriptions and SolutionsFigures Page Equipment Inspection General Product InformationProduct Description Product/System DescriptionRemoval from Skid Equipment HandlingHandling With Skid Liebert XDP strapped to piano jack Removing pallet boards for piano jack insertionSlide this runner away From the Liebert XDP Removing Piano JacksPositioning the Liebert XDP Liebert XDP dimensionsMechanical Considerations Model Pipe Connection Point 50/60 Hz Unit piping outlet connection sizes, inches, OD CuElectrical Information High Voltage Connections Connecting High-Voltage CablesElectrical enclosure knockout locations for field wiring High voltage connections-50Hz Extra Low Voltage ELV ConnectionsField Connections-Optional for All Units Field Connections-All UnitsConnection Sizes European Union Fluorinated Greenhouse Gas RequirementsPiping Recommended Pipe SizeLiebert XDP Interconnection with Liebert XD Cooling Modules Piping Installation MethodBypass Flow Controller Bypass flow controllers for a Liebert XDP-based systemBypass flow controller arrangement Bypass flow controller details, dimensionsPiping Details-Shut-Off/Isolation Valves Piping Installation MethodPiping Mains Evacuation and Leak CheckChecklist for Proper Installation Indicator Lights Description Green Red Checklist for Liebert XDP StartupLiebert XDP pump light indicator-208V and 400V units System R-134a liquid level Filling the Pumped Circuit-R-134aReturn Line Diameter System refrigerant charge for the supply and return mainsReturn Line Diameter 5/8 Calculating refrigerant charge-example Calculating Refrigerant Charge-ExampleWorksheet to calculate refrigerant charge Total 293Microprocessor Control Feature OverviewDisplay User interface keypad functionsViewing or Changing Settings Feature OverviewControls Main MenuAlarm History Active AlarmsSetpoints MIN Temp SPRestart Time Delay Setup OperationDegrees Pump Start TDPump Wait TD Liebert XDP DIP switches and factory settingsPump OFF TD Lead PumpValve Time Password Security-SETPT Password and Service PasswordChange Password-SETPT Password Alarm Enable Change Password-SERVICE PasswordAlarm Time Delay COM Alarm EnableCustom Text Custom AlarmsDiagnostics Alarm Descriptions and Solutions Alarm DescriptionsEnable or Disable Alarms Red and Green Lamp IndicatorsAlter Alarm Settings System Shutdown Causes Troubleshooting the XDP TroubleshootingFluorinated Greenhouse Gas Requirements MaintenanceLiebert XDP160 specifications SpecificationsIti Ne tTi n That
Top Page Image Contents