Liebert XDP Feature Overview, Microprocessor Control, Display, User interface keypad functions

Page 26

Microprocessor Control

4.0MICROPROCESSOR CONTROL

4.1Feature Overview

The microprocessor control for the Liebert XDP features an easy-to-use menu-driven LCD. The menus, control features and circuit board details are described in this section.

Figure 22 User interface

Status Display

Up Arrow Key

 

 

Down Arrow Key

On/Off Key

 

Alarm Silence Key

 

Active alarms are displayed on the LCD screen and sound an audible beep. To silence an alarm, press the Alarm Silence/Help key as prompted on the display.

Setpoints, DIP switch settings and other selections were made during factory testing of the unit based on typical operating conditions. (Other default selections were made according to options included with the unit.)

ADJUST THE FACTORY DEFAULTS ONLY IF THEY DO NOT MEET YOUR SPECIFICATIONS.

Allowable ranges are displayed by pressing the Help key. A password will be required (if enabled) to change setpoints, time delays, etc.

The display normally shows the leaving refrigerant temperature on the first line and alternates between the dew point and the number of alarms present on the second line.

4.1.1Display

To turn the unit On, press the On/Off (I/O) key after power is applied to the Liebert XDP. To turn the unit Off, press the On/Off (I/O) key before power is disconnected.

Table 12 User interface keypad functions

Keypad

Function

On/Off (I/O)

Turns the unit On or Off (top far left keypad)

 

 

Menu

Enables the user to access the program menu to change setpoints, alarms, etc. (top near left)

 

 

Up Arrow Key

Raises the value of displayed parameter while in a set mode (set points, time, etc).(arrow, top

near right)

 

Escape (Esc)

Allows user to move back to a previous menu (top far right)

 

 

Alarm Silence

If an alarm is present, press this key to silence the alarm. Help text will appear if this key is

pressed when no alarm is present (bottom left)

 

Down Arrow

Lowers the value of displayed parameter while in a set mode (set points, time, etc).(arrow,

Key

bottom near right).

Enter

After setting a control value, press ENTER to store the information in the microprocessor

(bottom right).

 

20

Image 26
Contents Liebert XDP Fluorinated Greenhouse Gas Requirements-European Union General Safety GuidelinesExample XDP160A Pumping Place holder Revision Unit Redundancy Level LiebertTable of Contents Alarm Descriptions and Solutions SpecificationsFigures Page Product Description General Product InformationEquipment Inspection Product/System DescriptionRemoval from Skid Equipment HandlingHandling With Skid Removing pallet boards for piano jack insertion Liebert XDP strapped to piano jackRemoving Piano Jacks Slide this runner away From the Liebert XDPPositioning the Liebert XDP Liebert XDP dimensionsMechanical Considerations Unit piping outlet connection sizes, inches, OD Cu Model Pipe Connection Point 50/60 HzConnecting High-Voltage Cables Electrical Information High Voltage ConnectionsElectrical enclosure knockout locations for field wiring Extra Low Voltage ELV Connections High voltage connections-50HzField Connections-All Units Field Connections-Optional for All UnitsPiping European Union Fluorinated Greenhouse Gas RequirementsConnection Sizes Recommended Pipe SizeBypass Flow Controller Piping Installation MethodLiebert XDP Interconnection with Liebert XD Cooling Modules Bypass flow controllers for a Liebert XDP-based systemBypass flow controller details, dimensions Bypass flow controller arrangementPiping Mains Piping Installation MethodPiping Details-Shut-Off/Isolation Valves Evacuation and Leak CheckChecklist for Proper Installation Indicator Lights Description Green Red Checklist for Liebert XDP StartupLiebert XDP pump light indicator-208V and 400V units Filling the Pumped Circuit-R-134a System R-134a liquid levelReturn Line Diameter System refrigerant charge for the supply and return mainsReturn Line Diameter 5/8 Worksheet to calculate refrigerant charge Calculating Refrigerant Charge-ExampleCalculating refrigerant charge-example Total 293Display Feature OverviewMicroprocessor Control User interface keypad functionsControls Feature OverviewViewing or Changing Settings Main MenuSetpoints Active AlarmsAlarm History MIN Temp SPDegrees Setup OperationRestart Time Delay Pump Start TDPump OFF TD Liebert XDP DIP switches and factory settingsPump Wait TD Lead PumpValve Time Password Security-SETPT Password and Service PasswordChange Password-SETPT Password Alarm Time Delay Change Password-SERVICE PasswordAlarm Enable COM Alarm EnableCustom Text Custom AlarmsDiagnostics Alarm Descriptions Alarm Descriptions and SolutionsEnable or Disable Alarms Red and Green Lamp IndicatorsAlter Alarm Settings System Shutdown Causes Troubleshooting Troubleshooting the XDPMaintenance Fluorinated Greenhouse Gas RequirementsSpecifications Liebert XDP160 specificationsTi n Ne tIti That