GE 300 Openings for input and output cable connections, Fixing of the UPS cabinet on the floor

Page 13

g

GE

Openings for input and output cable connections

S

U

1

0

_

p

to

w

ie

v

S

P

U

_

0

0

-3

5

2

2

_

S

G

S

64.96"
1,650mm	6.30"	1.58"
	160mm	1.58"
		40mm

Battery

		"
	6
.7		m
2
	m
0
7

Utility input

Output Load

				"
			6					"
	.6							"
1				m			0
2				m		.5
			m		1			m
		0			3			m
5							m
5						0
					0
					8

SG Series openings are provided on the top and the bottom of the UPS for the connection of input and output cables.

Fig. 3.4.1-2 Opening on top of the cabinet for input and output cables

																					0				64.96"
																					0			S	1,650mm
																							U
																				_		2
																			m
																		tto
																	o
																b									Utility input
										U					w
										U				ie
													v
												S
									_		P
		_						0																	Output Load
							0
						-3
					5
				2
S	S		2																											6.30"
G																														160mm							1.77"
																														160mm							1.77"
																																			45mm
																																		"
																																	6
																															.6
																														1				m				"
																														2				m				"
																																	m				0
																																0				.5
																														5					1			m
																														5					3			m
																																					m
																																				0
																											"								0
																											"								8
																										4				m
																									.9					m
																									3				m
																												0
																											0
																										1

Fig. 3.4.1-3 Opening on the bottom of the cabinet for input and output cables

Pay attention to the position of these

openings, when choosing the placement of the UPS.

These openings are

covered with a protective plate.

Fixing of the UPS cabinet on the floor

The UPS cabinet is free standing and normally does not require to be bolted to the floor.

The UPS cabinet can be fixed however to the floor by bolting it with the supporting blocks to the floor.

See Fig. 3.4.1-4.

1.378"	62.205"
35mm	1580mm

Ø 0.47305"	=
Ø 12mm

28.071"

713mm

=

SGS_225-300_UPS view bottom_02US

1.378"

35mm

2.363"	60mm
26.772"	680mm

2.363"

60mm

Front side

Fig. 3.4.1-4 Fixing of the UPS cabinet on the floor

OPM_SGS_ISG_M22_M30_0US_V011.doc

13/38

Installation Guide SG Series 225 & 300 kVA

Image 13

Contents SG Series Systems Copyright 2003 by GE Industrial SystemsStart UP and Commissioning Dear CustomerPreface Table of contents Battery InstallationGeneral StorageSafety instructions when working with battery Safety warnings Safety symbols and warningsRisk of electric shock PE Earth GND Ground Protective Grounding TerminalLayout SG Series 225 and 300 KVA LayoutWeight SG Series 225 and 300 kVA Dimensions and weightTransport Forklift Crane Transport UPS only in upright positionDelivery Storage of BatteryStorage of the UPS Positioning of the UPS SG Series Place of InstallationCheck -26A of the NEC code for specific requirements Fixing of the UPS cabinet on the floor Openings for input and output cable connections1-5 RPA system disposition Battery locationCFM Ventilation and CoolingUnpacking Take care not to damage the UPS when moving by forkliftPacking material recycling Separate input Rectifier & Bypass recommended Electrical WiringCommon input Rectifier & Bypass Neutral current could be greater than the phase currents Input/output over current protection and wire sizingPhase, 4 wire plus Ground Phase, 3 wire plus GroundWire positive and negative plus Ground See .7.1-1Copper Wire Size Range Wiring Connection1-1 Access to the input / output connections Common Input Rectifier / Bypass Power connection with common input utilityOutput Load Cable section for this connection shall be not less then AWG L1-1 Rectifier Phase a L1-2 Power connection separate input utilityL2-1 Rectifier Phase B L2-2 L3-1 Rectifier Phase C L3-2BR1 Battery Battery connectionPositive pole of the Battery Do not insert the Battery Fuses before the commissioningManual Bypass, serious damage to the Load could result Setup for SG Series when functioning as frequency converter1 RPA Parallel System Power Wiring of Parallel UnitsParallel Control BUS Connection UPSIntermediate units Terminal unitsControl BUS Cable Location Access to the control bus connectionControl bus cables connection Interface IM0048 going to P1311-3 Control Bus cable routing and connection Control bus cables routingCustomer Interface Customer Interface18, 19 Or J2 20, 21 NO, C, NC Acoustic Alarm 15, 16 Or J2 17, 18 NO, C, NC General AlarmOutput potential free contacts Or J2 / 1, 2 NO, C, NC Utility FailureGND JP3 EPO Emergency Power Off Input contact38/38