Cypress manual CYV15G0404DXB AC Electrical Characteristics, Parameter Description Min Max Unit

CYV15G0404DXB

CYV15G0404DXB AC Electrical Characteristics

Parameter			Description	Min.	Max	Unit
CYV15G0404DXB			Transmitter LVTTL Switching Characteristics Over the Operating Range
fTS			TXCLKx Clock Cycle Frequency	19.5	150	MHz
tTXCLK			TXCLKx Period=1/fTS	6.66	51.28	ns
tTXCLKH[20]			TXCLKx HIGH Time	2.2		ns
tTXCLKL[20]			TXCLKx LOW Time	2.2		ns
t		[20, 21, 22]	TXCLKx Rise Time	0.2	1.7	ns
TXCLKR
t		[20, 21, 22]	TXCLKx Fall Time	0.2	1.7	ns
TXCLKF
tTXDS			Transmit Data Set-up Time to TXCLKx↑ (TXCKSELx ≠ 0)	2.2		ns
tTXDH			Transmit Data Hold Time from TXCLKx↑ (TXCKSELx ≠ 0)	1.0		ns
fTOS			TXCLKOx Clock Frequency = 1x or 2x REFCLKx Frequency	19.5	150	MHz
tTXCLKO			TXCLKOx Period=1/fTOS	6.66	51.28	ns
tTXCLKOD			TXCLKO Duty Cycle centered at 60% HIGH time	–1.9	0	ns
CYV15G0404DXB			Receiver LVTTL Switching Characteristics Over the Operating	Range
fRS			RXCLKx± Clock Output Frequency	9.75	150	MHz
tRXCLKP			RXCLKx± Period = 1/fRS	6.66	102.56	ns
tRXCLKD			RXCLKx± Duty Cycle Centered at 50% (Full Rate and Half Rate when	–1.0	+1.0	ns
			RXCKSELx = 0)
tRXCLKR [20]			RXCLKx± Rise Time	0.3	1.2	ns
tRXCLKF [20]			RXCLKx± Fall Time	0.3	1.2	ns
t	[23]		Status and Data Valid Time to RXCLKx± (RXRATEx = 0, RXCKSELx = 0)	5UI–2.0[24]		ns
RXDv–			(Full Rate)
			Status and Data Valid Time to RXCLKx± (RXRATEx = 1, RXCKSELx = 0)	5UI–1.3[24]		ns
			(Half Rate)
t	[23]		Status and Data Valid Time to RXCLKx± (RXRATEx = 0, RXCKSELx = 0)	5UI–1.8[24]		ns
RXDv+			(Full Rate)
			Status and Data Valid Time to RXCLKx± (RXRATEx = 1, RXCKSELx =0)	5UI–2.6[24]		ns
			(Half Rate)
CYV15G0404DXB			REFCLKx Switching Characteristics Over the Operating Range
fREF			REFCLKx Clock Frequency	19.5	150	MHz
tREFCLK			REFCLKx Period = 1/fREF	6.6	51.28	ns
tREFH			REFCLKx HIGH Time (TXRATEx = 1)(Half Rate)	5.9		ns
			REFCLKx HIGH Time (TXRATEx = 0)(Full Rate)	2.9[20]		ns
tREFL			REFCLKx LOW Time (TXRATEx = 1)(Half Rate)	5.9		ns
			REFCLKx LOW Time (TXRATEx = 0)(Full Rate)	2.9[20]		ns
tREFD[25]			REFCLKx Duty Cycle	30	70	%
tREFR [20, 21, 22]			REFCLKx Rise Time (20%–80%)		2	ns
tREFF[20, 21, 22]			REFCLKx Fall Time (20%–80%)		2	ns

Notes

20.Tested initially and after any design or process changes that may affect these parameters, but not 100% tested.

21.The ratio of rise time to falling time must not vary by greater than 2:1.

22.For a given operating frequency, neither rise or fall specification can be greater than 20% of the clock-cycle period or the data sheet maximum time.

23.Parallel data output specifications are only valid if all outputs are loaded with similar DC and AC loads.

24.Receiver UI (Unit Interval) is calculated as 1/(fREF * 20) (when TXRATEx = 1) or 1/(fREF * 10) (when TXRATEx = 0). In an operating link this is equivalent to tB.

25.The duty cycle specification is a simultaneous condition with the tREFH and tREFL parameters. This means that at faster character rates the REFCLKx± duty cycle cannot be as large as 30%–70%.

Document #: 38-02097 Rev. *B Page 28 of 44

[+] Feedback