Briggs & Stratton 30A NEMA 1, 71017 manual Troubleshooting, Problem Cause Solution

Page 15

TROUBLESHOOTING

TROUBLESHOOTING

	Problem	Cause		Solution

		1.	Generator circuit breaker is	1.	Reset circuit breaker.
			open.
		2.	Poor connection or defective	2.	Check and repair.
	Generator is running, but no AC		cord set.
	output is available.	3.	Connected device is bad.	3.	Select a different appliance or
					load that is in good condition.
		4.	Fault in generator.	4.	Contact authorized service
					center.

		1.	Short circuit in a connected	1.	Disconnect shorted electrical
	Generator runs good but bogs		load.		load.
	down when loads are connected.	2.	Generator is overloaded.	2.	See “Load Management” on page
					13.

		1.	Transfer switch in GENERATOR	1.	Set switch to UTILITY position.
	Appliances don’t work after utility		position.
	power comes back on.	2.	Circuit breaker in main	2.	Reset circuit breaker in main
			distribution panel is open.		distribution panel.

		1.	Ground fault in connected load.	1.	Remove load with fault.
	GFCI breaker in generator control	2.	Defective GFCI device.	2.	Contact authorized service
	panel trips.				center.
	panel trips.	3.	Neutral bonded to ground in	3.	Contact authorized service
		3.	Neutral bonded to ground in	3.	Contact authorized service
			transfer switch.		center.

15

Image 15

Contents 30A Nema 1 / Nema 3R Table of Contents Contact with live parts can cause electric shock or burn Important Safety InstructionsFor the Installing Dealer/Contractor IntroductionFor the Home Owner Generator Compatibility Installer ResponsibilitiesOwner Orientation Equipment DescriptionDelivery Inspection InstallationItems Not Shipped with Transfer Switch UnpackingMounting Guidelines Typical Switch MountingEssential Circuit Isolation Typical System Diagram with Essential CircuitsPower Wiring Interconnections Main Distribution Panel Inlet Box Inlet Box Connections Connecting Cord SetLoad Management To transfer from utility power to generator powerTo transfer from generator power back to utility power System OperationSpecifications When Calling the FactoryUL 1008 Listed Transfer Switch Model Problem Cause Solution TroubleshootingTransfer Switch Service Parts Model 071014 Nema Model 071017 Nema 3RDescription Warranty Period Table DES Matières Conservez CES Directives AvertissementRemarque Au détaillant/à l’entrepreneur procédant à l’installation IntroductionPour le propriétaire résidentiel Génératrices compatibles Responsabilités de l’installateurOrientation du propriétaire Description de l’équipementArticles non inclus avec le commutateur de transfert InstallationDéballage Vérification de la livraisonDirectives d’assemblage Installation typique de commutateur de transfertIsolation DES Circuits Essentiels Utility ServiceInterconnexions du câblage d’alimentation Principal Boîte d’entrée Cordon de raccordement Raccords de la boite d’entréeGestion des charges Utilisation DU SystèmeSpécifications Si vous téléphonez au manufacturierCommutateur de transfert homologué UL Modèle Dépannage Problème Cause SolutionRemarques Période DE Garantie Introducción ÍndiceAviso Conserve Estas InstruccionesInstrucciones Importantes DE Seguridad AdvertenciaIntroducción Para el usuario domésticoPara el distribuidor/técnico instalador Compatibilidad del generador Orientación al propietarioResponsabilidades del instalador Descripción del equipoElementos no incluidos con el conectador InstalaciónDesembalaje Inspección en el momento de la entregaFigura 26 Montaje habitual del conectador Directrices de montajeAislamiento DE Circuitos Esenciales Figura 27 Diagrama del sistema con circuitos esencialesInterconexión de los cables de alimentación Figura 28 Diagrama de instalación habitual del conectador Figura 30 Instalación del cuadro de entrada Cuadro de entradaConexión del juego de cables Figura 31 Conexiones del cuadro de entradaGestión de cargas Funcionamiento DEL SistemaEspecificaciones Para llamar a la fábricaInterruptor de transferencia UL Modelo Problema Causa Solución Resolución DE ProblemasPeríodo DE Garantía