Olivetti 16W, 20W operation manual Changing a TRAY’S Paper Size Setting, Envelopes

Page 20

BEFORE USING THE MACHINE

Envelopes

Do not use the following envelopes, as misfeeds will occur.

Envelopes with metal tabs, clasps, strings, holes, or windows.

Envelopes with rough fibres, carbon paper, or glossy surfaces.

Envelopes with two or more flaps.

Envelopes with tape, film, or paper attached to the flap.

Envelopes with a fold in the flap.

Envelopes with glue on the flap to be moistened for sealing.

Envelopes with labels or stamps.

Envelopes that are slightly inflated with air.

Envelopes with glue protruding from the seal area.

Envelopes with part of the seal area peeled off.

CHANGING A TRAY’S PAPER SIZE SETTING

Follow these steps to change a tray’s paper size setting.

The paper size setting cannot be changed when the machine has stopped temporarily due to running out of

Note

paper or a misfeed, or during interrupt copying.

During printing (even in copy mode), the paper size setting cannot be changed.

A5 (5-1/2" x 8-1/2") size paper can only be selected in upper paper tray.

Do not load paper that is a different size than the paper size setting. Copying will not be possible.

1 Hold down the [PAPER SIZE ENTER] key () for more than 5 seconds to set the selected paper size.

 

The currently selected

 

paper feed location

A3

indicator will blink and the

A4

corresponding paper size

A4

A5

(which is currently set)

B4

XTRA

indicator will light steadily. All other indicators will go out.

3 Use the [ORIGINAL SIZE ENTER] key (ENTER ) to select the paper size.

 

 

The indicator of the

 

 

selected paper size lights

 

A3

up.

ENTER

A4

 

A4

 

 

 

 

A5

 

 

B4

 

 

TRA

 

2 If the machine has two paper trays, use the [TRAY SELECT] key () to select the paper tray for which you wish to change the paper size setting.

Each time the [TRAY SELECT] key () is pressed, a paper tray will be indicated with a blinking paper feed location indicator.

16

Image 20
Contents Copia 16W d-Copia 20W Copia 16W Copia 20WPublication Issued by Page For Countries in the European Union EU Contents Troubleshooting Important Points When Selecting AN Installation Site Do not install your machine in areas that areEnvironmental Information Trademark acknowledgementsOnline Manual on the accessory CD-ROM Software Setup Guide separate manualMeaning of R in Original and Paper Size Indications Conventions Used in this ManualDifferences Between Models AB series metric and inch series referencesEnhanced copying features High-speed laser copyingHigh-quality digital image Scan once/Print manyPress to turn the machine power on and off. p.12 Contains operation keys and indicator lights. p.10Adjust to the width of the paper. p.15 Use to clean the transfer charger. p.57Adjust to the size of the originals Open to remove misfed originals. p.47Originals exit the machine here after copying Contains toner. p.54Operation Panel Light up to show the selected copy paper size. p.16 Use to set the paper size in the paper trays. p.16Use to manually select a paper tray. p.21 Press for automatic copy ratio selection. p.22Power on Power OFFPower Save Modes Initial settingsFollow these guidelines when using special papers PaperSpecial papers For best results, use only Olivetti recommended paperLoading Paper Loading the paper trayPush the centre Pressure plate down until It locks into placeImportant points when inserting paper in the bypass tray Loading the bypass trayChanging a TRAY’S Paper Size Setting EnvelopesPress the Start key and then the Paper Size Enter key Open the document cover/SPF, and place the original Normal CopyingCopying from the document glass Copying from the SPF Set the originals face up in the document feeder trayAuto paper select mode Two-tray model only Auto tray switching Two-tray model only Making a Copy Darker or LighterSelecting the Tray Original typesSetting the Number of Copies REDUCTION/ENLARGEMENT/ZOOMAutomatic Ratio Selection Original position Selectable ratiosSelecting a preset ratio Fine adjustment of the ratioManual Ratio Selection Press the Auto Image key Auto %XY Zoom copying Press the Copy ratio display keyPress the Copy ratio display key Place original B as shown below TWO-SIDED Copying Using the Bypass TrayCopy original a Copy indicator Is lit Dual page CopyingSet the original size to A3 11 x Press the Dual page Copy keyReplace the previous originals and press the Start key Interrupting a Copy RUNPress the Interrupt key to interrupt the copy run Using the Printer Mode Basic Procedure for PrintingMaketray. sure that paper is loaded Click the Print button or the OK button to begin printingPausing a print job When Use close paper size is disabledWhen Use close paper size is enabled Operation in Copy and Printer ModesTo complete Adjusting the Automatic Exposure LevelSetting Toner Save Mode and High Image Quality Mode When enabling tonerPhoto indicator stops blinking and lights steadily Save mode, make sureCustomising Settings User Programs300 dpi MinimumShort beep CopiesSelecting a Setting for a User Program Base settingsAuditing Mode Settings Settings for Auditing ModeAuditing Mode Selecting Auditing Mode Settings For the setting codes, see Auditing Mode SETTINGS. p.36Auditing mode Account number entryAccount number change Account number deletionResetting account Copying when Auditing mode is enabledTroubleshooting MACHINE/COPYING Problems Problem Cause and solution Misfeed occurs Paper is not loaded properlyPieces of paper inside machine Paper misfeed Too much paper is loaded in the trayAny other indicators are lit Original smudged or blotchyCopies Transfer charger is dirty Copying or printing is performedPrinting Problems Click Add or Remove Programs Removing the softwareClick the start button, and then click Control Panel Indicators and Display Messages Misfeed Removal Misfeed in the SPFRemove the misfed original Copia 20W Copia 16WMisfeed indicator will go out Misfeed in the Bypass TrayMisfeed in the Machine Misfeed in the paper feed areaMisfeed in the fusing area Lower the fusing unit release levers toAllow easier removal Misfed paper duringMisfeed in the transport area Close the side coverBe careful not to tear the misfed paper during removal Be careful not to tear Misfed paper during RemovalPush the upper paper tray in completely Misfeed in the Upper Paper TrayClose the upper paper tray Open the lower side cover Remove the misfed paperClose the lower side cover Close the lower paper trayToner cartridge replacement required indicator will go out Replacing the Toner CartridgeClose the front cover Green part of the cartridgeChecking the Total Output Count and Toner Level Checking the Total Output CountTotal output count Total copy countRoutine Maintenance Cleaning the Document Glass and SPF/ Document CoverChecking the Toner Level Press the Light key to return to the normal displayCleaning the Bypass Tray Paper Feed Roller Cleaning the Transfer ChargerSingle Pass Feeder SpecificationsPeripheral Devices Storage of Supplies Proper StorageStore the supplies in a location that is Store paper in the wrapper and lying flatSpecifications Printer Function Software License Page Symbols IndexPreset Ratio selector indicator TroubleshootingOriginal types 10, 13Indicators, lit and blinking Machine settingsProblem occurs Page Class Laser Product Laser Klasse Page Code