Olivetti 16W Auditing mode, Account number entry, Account number change, Account number deletion

Page 42

USER SETTINGS

Auditing mode

(program No.10)

1Press the [1] key to enable "Auditing mode" or the [0] key to disable it, and then press the [START] key ().

After enabling "Auditing mode", use "Account Note number entry" to establish account numbers

for each account (up 20 accounts can be established).

2 Press the [CLEAR] key ().

Account number entry

(program No.11)

If 20 accounts have already been established, the error code "11E" will appear in the display.

1Use the numeric keys to enter a 3-digit number (any number except "000") and then press the [START] key ().

• If you enter "000" or a number that has

Note already been stored, the number will blink in the display. Enter a different number. (Up to 20 accounts can be established.)

Repeat the same procedure to enter any other account numbers that you wish to establish.

Keep a record of what group is using each account number (account names cannot be stored, so keep a record to prevent confusion when totalling account values).

2 Press the [CLEAR] key ().

Account number change

(program No.12)

Use this procedure to change an account number. If no account numbers have been established, the error code "12E" will appear in the display.

1Press the [Copy ratio display] key ( ) to select the account number that you wish to change, and then press the [START] key ().

The display will show 3 blinking hyphens "- - -".

2Press the numeric keys to enter a new account number (any 3-digit number except "000"), and then press the [START] key ().

• If you enter "000" or a number that has

Note already been stored, the number will blink in the display. Enter a different number.

To change another account number, repeat steps 1 and 2.

3When finished, press the [CLEAR] key ().

Account number deletion

(program No.13)

Use this procedure to delete account numbers. A single account number can be deleted, or all account numbers at once.

If no account numbers have been established, the error code "13E" will appear in the display.

[Deleting all accounts at once]

Press the [1] key and then press the [START] key ().

All account numbers will be deleted.

[Deleting a single account]

1Press the [0] key, and then press the [START] key ().

2Select the account number to be deleted with the [Copy ratio display] key ( ) and then press the [START] key ().

To delete another account number, enter the Note program number (13) for account number

deletion and then repeat the procedure for "Deleting a single account".

Number of copies per account

(program No.14)

Use this procedure to display the copy count of each account. If no account numbers have been established, the error code "14E" will appear in the display.

1Select the account number with the [Copy ratio display] key ( ).

2Hold down the [0] key.

The copy count of the selected account will appear in the display while you hold down the [0] key. The count is displayed sequentially as shown below.

Example: 12,345 copies

Note

• Each A3 (11" x 17") size page is counted as

two pages.

To view the copy count of another account, repeat steps 1 and 2.

3When finished, press the [CLEAR] key ().

38

Image 42
Contents Copia 16W d-Copia 20W Copia 16W Copia 20WPublication Issued by Page For Countries in the European Union EU Contents Troubleshooting Important Points When Selecting AN Installation Site Do not install your machine in areas that areEnvironmental Information Trademark acknowledgementsMeaning of R in Original and Paper Size Indications Online Manual on the accessory CD-ROMSoftware Setup Guide separate manual Conventions Used in this ManualDifferences Between Models AB series metric and inch series referencesHigh-quality digital image Enhanced copying featuresHigh-speed laser copying Scan once/Print manyAdjust to the width of the paper. p.15 Press to turn the machine power on and off. p.12Contains operation keys and indicator lights. p.10 Use to clean the transfer charger. p.57Originals exit the machine here after copying Adjust to the size of the originalsOpen to remove misfed originals. p.47 Contains toner. p.54Operation Panel Use to manually select a paper tray. p.21 Light up to show the selected copy paper size. p.16Use to set the paper size in the paper trays. p.16 Press for automatic copy ratio selection. p.22Power Save Modes Power onPower OFF Initial settingsSpecial papers Follow these guidelines when using special papersPaper For best results, use only Olivetti recommended paperPush the centre Loading PaperLoading the paper tray Pressure plate down until It locks into placeImportant points when inserting paper in the bypass tray Loading the bypass trayChanging a TRAY’S Paper Size Setting EnvelopesPress the Start key and then the Paper Size Enter key Normal Copying Copying from the document glassOpen the document cover/SPF, and place the original Copying from the SPF Set the originals face up in the document feeder trayAuto paper select mode Two-tray model only Selecting the Tray Auto tray switching Two-tray model onlyMaking a Copy Darker or Lighter Original typesAutomatic Ratio Selection Setting the Number of CopiesREDUCTION/ENLARGEMENT/ZOOM Original position Selectable ratiosManual Ratio Selection Selecting a preset ratioFine adjustment of the ratio Press the Auto Image key Auto %XY Zoom copying Press the Copy ratio display keyPress the Copy ratio display key TWO-SIDED Copying Using the Bypass Tray Copy original aPlace original B as shown below Set the original size to A3 11 x Copy indicator Is litDual page Copying Press the Dual page Copy keyInterrupting a Copy RUN Press the Interrupt key to interrupt the copy runReplace the previous originals and press the Start key Maketray. sure that paper is loaded Using the Printer ModeBasic Procedure for Printing Click the Print button or the OK button to begin printingWhen Use close paper size is enabled Pausing a print jobWhen Use close paper size is disabled Operation in Copy and Printer ModesAdjusting the Automatic Exposure Level SettingTo complete Photo indicator stops blinking and lights steadily Toner Save Mode and High Image Quality ModeWhen enabling toner Save mode, make sureCustomising Settings User ProgramsShort beep 300 dpiMinimum CopiesSelecting a Setting for a User Program Base settingsSettings for Auditing Mode Auditing ModeAuditing Mode Settings Selecting Auditing Mode Settings For the setting codes, see Auditing Mode SETTINGS. p.36Account number change Auditing modeAccount number entry Account number deletionResetting account Copying when Auditing mode is enabledTroubleshooting MACHINE/COPYING Problems Pieces of paper inside machine Problem Cause and solution Misfeed occursPaper is not loaded properly Paper misfeed Too much paper is loaded in the trayCopies Transfer charger is dirty Any other indicators are litOriginal smudged or blotchy Copying or printing is performedPrinting Problems Removing the software Click the start button, and then click Control PanelClick Add or Remove Programs Indicators and Display Messages Remove the misfed original Misfeed RemovalMisfeed in the SPF Copia 20W Copia 16WMisfeed indicator will go out Misfeed in the Bypass TrayMisfeed in the Machine Misfeed in the paper feed areaAllow easier removal Misfeed in the fusing areaLower the fusing unit release levers to Misfed paper duringBe careful not to tear the misfed paper during removal Misfeed in the transport areaClose the side cover Be careful not to tear Misfed paper during RemovalMisfeed in the Upper Paper Tray Close the upper paper trayPush the upper paper tray in completely Close the lower side cover Open the lower side coverRemove the misfed paper Close the lower paper trayClose the front cover Toner cartridge replacement required indicator will go outReplacing the Toner Cartridge Green part of the cartridgeTotal output count Checking the Total Output Count and Toner LevelChecking the Total Output Count Total copy countChecking the Toner Level Routine MaintenanceCleaning the Document Glass and SPF/ Document Cover Press the Light key to return to the normal displayCleaning the Bypass Tray Paper Feed Roller Cleaning the Transfer ChargerSpecifications Peripheral DevicesSingle Pass Feeder Store the supplies in a location that is Storage of SuppliesProper Storage Store paper in the wrapper and lying flatSpecifications Printer Function Software License Page Symbols IndexOriginal types Preset Ratio selector indicatorTroubleshooting 10, 13Machine settings Problem occursIndicators, lit and blinking Page Class Laser Product Laser Klasse Page Code