Ultra electronic ID Card Printer manual Installing the card stacker, Discharging the card

Page 14

(to the next page)

Installing the card stacker

1. Mount the card stacker on the printer.

Hang the stacker claw on the stacker receptacle.

Card discharge slot

Claw	Card stacker
	receptacle
Card stacker
(accessory)

Discharging the card

When correctly printed, the cards are discharged from the left side.

If a card jam or a write error on magnetic stripes occurs on the way, results differ depending on the areas.

Portion A: If a card jam or a write error on magnetic stripes occurs on the way, press the RESET button, then the ENTER button. The printer is initialized, and the cards are discharged from the right side of the printer.

Portion B: See the description in Jam (Transfer) on p.45.

Portion C: When correctly printed, the cards are discharged from the left side of the printer. The cards jamming around this area are also discharged from the left side.

The card stacker is capable of containing approximately 100 0.76mm-thick cards or 280 0.25mm- thick cards at the maximum.

CAUTION

Be sure to hang the card stacker

claw on the card stacker receptacle, not the card discharge slot. If you mount the card stacker at a wrong place, cards are not discharged, resulting in a card jam.

Retransfer film cassette

Ink ribbon cassette

Thermal head

Magnetic head

Card turnover table

Feed roller

NG card discharge slot

Cleaning roller

Card feed roller

Retransfer roller (heat roller)

Bent remedial roller (heat roller)

C BA

13

Image 14

Contents ID Card Printer Magicard Prima Re-transfer Laminating Printer Declaration of Conformity For USA only Machine NoiseContents Do not wet the machine with water Do not touch the power plug during electrical StormsDo not use a line voltage other than instructed Do not touch the machine with wet handsHold the body of the power plug when pulling it Out Do not use the machine while it has a faultPull out the power plug before cleaning Machine Do not touch the power plug with a wet handBefore use Product featuresChecking accessories Handling of transfer film Ink ribbons and cardsInstallation Names of parts Set-up Connecting with a host computerSet the BUS switches Set the Scsi IDConnect the IC unit with the host computer Connecting the IC unit Sold separatelyConnect the printer and IC unit Compact IC unit sold separately Connecting the power cordPlug the power cable into the printer Connect the compact IC unit to the host computerHang the stacker claw on the stacker receptacle Installing the card stackerMount the card stacker on the printer Discharging the cardPlace the cassette upright on a flat surface during set-up Setting the ink ribbonRemove the ink ribbon cassette Wind the ribbon, taking up the slackClose the printer door When the ink ribbon is wound up to the endInsert the cassette along the guide rail Setting the retransfer film Remove the retransfer film cassetteWind the retransfer film to take up the slack Setting the number of frames to be usedWhen the retransfer film is wound up to the end Open the printer door and insert the cassetteSetting cards Open the card trayPull the card bracket back Card bracket locks when it reaches the holeInserting cards Unit can take about 300 0.76mm-thick cards Close the card trayFor JIS II cards When using magnetic cards Loading cardsWhen using contact IC cards For ISO cardsMalfunction of the printer Switching the card thicknessRemove the card thickness switching plate Remove the blue securing screwNames of parts on the operation Panel Operation display LED contents LCD panel LCD operation display contentTurning on the power OperationTurn off the printer’s power Turning off the powerAbout the Reset button Initialized without winding up. DefaultUser mode screen flow User modesUser mode settings Main menu SubmenuDisplay mode settings Exit user mode Cleaning modePress Enter to reset Clearing the free counterInk mode setting Set retransfer film Retransfer mode settingSet the retransfer temperature Set the retransfer speedBuzzer mode setting Setting the bend remedy mode Transport mode Card size setting modeAntimagnetic setting mode Test printRemove the cleaning unit Care and cleaningCleaning the cleaning rollers Cleaning the thermal head Wipe the head indicated with horizontallyCleaning the fan filter on the back side How to attach the spongeFrom user mode select cleaning mode Cleaning the card feed rollersSet a cleaning card Turn off the power after the cleaning card is dischargedApply alcohol on the magnetic head cleaning card Cleaning the card feed rollers Heat rollersOnce printer servicing and cleaning Have been completed Set the card on the card trayLayout of rollers inside the printer TroubleshootingCleaning rollers Card turnover tableError code listing Meaning of reset → enter buttons in the list isTroubleshooting About printing errors Mending broken ink ribbon Retransfer filmPush the card tray back into position on an angle Removing card jamsReturn the card tray to its original position Turn the jog dial Remove any jammed cardsJog lever are supplied as standard Remove the cardSpecifications Main specificationsUnit/mm External appearance and dimensionsFront view Ultra Electronics Card Systems