Ultra electronic ID Card Printer manual Switching the card thickness, Malfunction of the printer

Page 22

Switching the card thickness

Depending on the material, some 0.25mm thick cards may not be suitable for printing. Consult your dealer regarding the materials and specifications of the card before purchasing.

WARNING

⬤Before switching the thickness, turn off the printer and the devices connecting to the printer, and take off their power plugs from

Electric shock the outlet to prevent an electric shock.

CAUTION

⬤When switching the card thickness, be careful not to remove the screws except

those instructed. Removing uninstructed screws may cause injuries or a

Injury	malfunction of the printer.

1. Remove the blue securing screw.

CAUTION

Do not remove the screws other than blue ones. Removing other screws may cause a malfunction of the printer.

Plate securing screw

76	.
.	0
0	25

3. Remove the card thickness switching plate and invert the direction.

.25	.
	0
0	76

Move the plate back into position securely and tighten the screw.

4. Checking card feed

Set a few cards on the card tray.

Turn the roller drive gear in the arrow direction, and check that only one card is fed at a time.

Roller drive gear

The card having a thickness value written on this side is discharged.

	.25	0
	0	0
	0	.
		76

2. Remove the card thickness switching plate.

Pull the plate up while pressing the left and right knobs toward the center.

Thickness switching plate

.76	.
	0
0	25

Memo

If the card thickness is not switching properly, or cards cannot be fed because of the dirt on the feed roller,

J A M ( H o p p e r )

appears on the LCD panel.

Check the proper setting of the card thickness plate, and clean the feed roller (see p.40).

21

Image 22

Contents ID Card Printer Magicard Prima Re-transfer Laminating Printer Declaration of Conformity For USA only Machine NoiseContents Do not wet the machine with water Do not touch the power plug during electrical StormsDo not use a line voltage other than instructed Do not touch the machine with wet handsHold the body of the power plug when pulling it Out Do not use the machine while it has a faultPull out the power plug before cleaning Machine Do not touch the power plug with a wet handBefore use Product featuresChecking accessories Handling of transfer film Ink ribbons and cardsInstallation Names of parts Set-up Connecting with a host computerSet the BUS switches Set the Scsi IDConnect the printer and IC unit Connecting the IC unit Sold separatelyConnect the IC unit with the host computer Compact IC unit sold separately Connecting the power cordPlug the power cable into the printer Connect the compact IC unit to the host computerHang the stacker claw on the stacker receptacle Installing the card stackerMount the card stacker on the printer Discharging the cardPlace the cassette upright on a flat surface during set-up Setting the ink ribbonRemove the ink ribbon cassette Wind the ribbon, taking up the slackInsert the cassette along the guide rail When the ink ribbon is wound up to the endClose the printer door Setting the retransfer film Remove the retransfer film cassetteWind the retransfer film to take up the slack Setting the number of frames to be usedWhen the retransfer film is wound up to the end Open the printer door and insert the cassetteSetting cards Open the card trayPull the card bracket back Card bracket locks when it reaches the holeInserting cards Unit can take about 300 0.76mm-thick cards Close the card trayFor JIS II cards When using magnetic cards Loading cardsWhen using contact IC cards For ISO cardsMalfunction of the printer Switching the card thicknessRemove the card thickness switching plate Remove the blue securing screwNames of parts on the operation Panel Operation display LED contents LCD panel LCD operation display contentTurning on the power OperationTurn off the printer’s power Turning off the powerAbout the Reset button Initialized without winding up. DefaultUser mode screen flow User modesUser mode settings Main menu SubmenuDisplay mode settings Exit user mode Cleaning modePress Enter to reset Clearing the free counterInk mode setting Set retransfer film Retransfer mode settingSet the retransfer temperature Set the retransfer speedBuzzer mode setting Setting the bend remedy mode Transport mode Card size setting modeAntimagnetic setting mode Test printCleaning the cleaning rollers Care and cleaningRemove the cleaning unit Cleaning the thermal head Wipe the head indicated with horizontallyCleaning the fan filter on the back side How to attach the spongeFrom user mode select cleaning mode Cleaning the card feed rollersSet a cleaning card Turn off the power after the cleaning card is dischargedApply alcohol on the magnetic head cleaning card Cleaning the card feed rollers Heat rollersOnce printer servicing and cleaning Have been completed Set the card on the card trayLayout of rollers inside the printer TroubleshootingCleaning rollers Card turnover tableError code listing Meaning of reset → enter buttons in the list isTroubleshooting About printing errors Mending broken ink ribbon Retransfer filmReturn the card tray to its original position Removing card jamsPush the card tray back into position on an angle Turn the jog dial Remove any jammed cardsJog lever are supplied as standard Remove the cardSpecifications Main specificationsFront view External appearance and dimensionsUnit/mm Ultra Electronics Card Systems