Ultra electronic ID Card Printer manual Connecting the IC unit Sold separately

Page 12

(to the next page)

Connecting the IC unit

(sold separately)

Large and compact size IC units are sold separately, as are specialized optional devices for the unit. Consult your dealer for more details.

WARNING

⬤Make sure that the power switch is turned OFF and the AC cable is detatched from the plug, before connecting and

Electric	disconnecting the IC units. Otherwise
shock	electric shocks, fires or malfunction of the
	product may occur.

⬤Using IC units other than those specified may cause electric shocks, fires or malfunction of the product.

Large size IC unit (sold separately)

1. A joint plate for an IC unit is provided as an accessory.

2. Fit the printer and IC unit into the holes as shown.

CX21ICL*

3. Connect the printer and IC unit.

Connect the cable which comes with the IC unit to the OPTION 1 terminal.

Connecting to the PRT interface terminal

Connection cable (Accessory)

Use the OPTION 1 side. If you use side 2 it does not function.

4. Connect the IC unit with the host computer.

Connect interface cables which are commercially available.

The terminal is rotated 180°

Commercial item

Terminals on the rear of the IC unit SERIAL1:non-contact SERIAL2:contact

CX21ICL* is manufactured by Victor Data Systems Company of Japan, Limited.

CAUTION

Unstable locations and angled surfaces may cause card feeder malfunctions. Make sure to fit the devices into the holes securely. Furthermore, install the printer on a flat and hard surface.

11

Image 12

Contents ID Card Printer Magicard Prima Re-transfer Laminating Printer Declaration of Conformity For USA only Machine NoiseContents Do not touch the power plug during electrical Storms Do not use a line voltage other than instructedDo not wet the machine with water Do not touch the machine with wet handsDo not use the machine while it has a fault Pull out the power plug before cleaning MachineHold the body of the power plug when pulling it Out Do not touch the power plug with a wet handProduct features Checking accessoriesBefore use Handling of transfer film Ink ribbons and cardsInstallation Names of parts Connecting with a host computer Set the BUS switchesSet-up Set the Scsi IDConnecting the IC unit Sold separately Connect the printer and IC unitConnect the IC unit with the host computer Connecting the power cord Plug the power cable into the printerCompact IC unit sold separately Connect the compact IC unit to the host computerInstalling the card stacker Mount the card stacker on the printerHang the stacker claw on the stacker receptacle Discharging the cardSetting the ink ribbon Remove the ink ribbon cassettePlace the cassette upright on a flat surface during set-up Wind the ribbon, taking up the slackWhen the ink ribbon is wound up to the end Insert the cassette along the guide railClose the printer door Setting the retransfer film Remove the retransfer film cassetteSetting the number of frames to be used When the retransfer film is wound up to the endWind the retransfer film to take up the slack Open the printer door and insert the cassetteSetting cards Open the card trayCard bracket locks when it reaches the hole Inserting cards Unit can take about 300 0.76mm-thick cardsPull the card bracket back Close the card trayWhen using magnetic cards Loading cards When using contact IC cardsFor JIS II cards For ISO cardsSwitching the card thickness Remove the card thickness switching plateMalfunction of the printer Remove the blue securing screwNames of parts on the operation Panel Operation display LED contents LCD panel LCD operation display contentTurning on the power OperationTurning off the power About the Reset buttonTurn off the printer’s power Initialized without winding up. DefaultUser mode screen flow User modesUser mode settings Main menu SubmenuDisplay mode settings Cleaning mode Press Enter to resetExit user mode Clearing the free counterInk mode setting Retransfer mode setting Set the retransfer temperatureSet retransfer film Set the retransfer speedBuzzer mode setting Setting the bend remedy mode Card size setting mode Antimagnetic setting modeTransport mode Test printCare and cleaning Cleaning the cleaning rollersRemove the cleaning unit Cleaning the thermal head Wipe the head indicated with horizontallyCleaning the fan filter on the back side How to attach the spongeCleaning the card feed rollers Set a cleaning cardFrom user mode select cleaning mode Turn off the power after the cleaning card is dischargedCleaning the card feed rollers Heat rollers Once printer servicing and cleaning Have been completedApply alcohol on the magnetic head cleaning card Set the card on the card trayTroubleshooting Cleaning rollersLayout of rollers inside the printer Card turnover tableError code listing Meaning of reset → enter buttons in the list isTroubleshooting About printing errors Mending broken ink ribbon Retransfer filmRemoving card jams Return the card tray to its original positionPush the card tray back into position on an angle Remove any jammed cards Jog lever are supplied as standardTurn the jog dial Remove the cardSpecifications Main specificationsExternal appearance and dimensions Front viewUnit/mm Ultra Electronics Card Systems