Ultra electronic ID Card Printer Card size setting mode, Antimagnetic setting mode, Test print

Page 35

Operation (continued)

Card size setting mode

IC contact setting mode

The printer is designed to load two sizes of cards. Set the card size according to the card to be printed.

> C a r d S i z e

EXIT

When using IC cards, specify the contact position to stop the cards.

> I C C o n t a c t P o s .

EXIT

S t a n a r d

Set the card size:

2 settings [Standard and Cybernetic]

Exit user mode

ENTER

N o n e

Set IC contact position:

3 settings

Exit user mode

ENTER

Press to select the setting and press to save.

(The electronic beep sounds.)

Standard:

54.0mm ⋅ 85.6mm (complies with ISO7810)

Cybernetic:

57.5mm ⋅ 85.0mm

Antimagnetic setting mode

Set antimagnetic force for writing data on the ISO compatible magnetic stripe card.

> M G I S O T y p e

 

 

 

EXIT

 

Exit user mode

 

 

 

 

 

L o - C o

 

 

 

 

 

 

 

 

ENTER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

to select the

to save.

Press

 

 

setting and press

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(The electronic beep sounds.)

 

Lo-Co

 

 

 

 

 

 

 

 

 

238⋅102 [A/m] (300 [Oe])

 

 

 

 

 

Hi-Co

 

 

 

 

 

 

 

 

 

218⋅103 [A/m] (2750 Oe])

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press to select the setting and press to save.

(The electronic beep sounds.)

None

No contact

Built-in

A built-in contact is being used

Ext. Unit

An IC unit contact is being used

Test print

Test print is provided for printing a test pattern contained in the printer (there is only one pattern). Operating the printer independent of the host computer enables you to find out the source of trouble if there is a problem in the system.

> T e s t P r i n t

 

EXIT

 

O K ?

 

Exit user mode

 

 

 

 

 

 

 

 

Press ENTER to carry out test printing.

 

(The electronic beep sounds.)

P r i n t i n g . .

Non-contact IC antenna setting mode

To use non-contact IC cards, set the antenna position at which the cards stop.

> I C A n t e n n a P o s .

EXIT

Exit user mode

N o n e

Non-contact IC antenna position: 4 settings

Press

to select the ENTER

to save.

setting and press

 

 

 

(The electronic beep sounds.)

None

No antenna

Built-in

A built-in antenna is being used

Ext. Unit

An IC unit antenna is being used

Added on

A compact IC unit is being used.

34

A single-sided color pattern is printed. When test printing is completed, the unit will automatically return to ready staus.

Transport mode

To set the transport mode.

> T e s t P r i n t

 

EXIT

 

O K ?

 

Exit user mode

 

 

 

 

 

 

 

 

Press ENTER to carry out transport mode.

 

(The electronic beep sounds.)

 

 

Please turn off the power.

P l e a s e ,

 

P o w e r o f f

 

Turnning on the power, then the

 

transport mode is canceled.

CAUTION

When shipping or moving the

printer, you must set the transport mode. If the printer is not set the transport mode, it may have a damage.

Page 34 Page 36
Image 35
Page 34 Page 36
Contents ID Card Printer Magicard Prima Re-transfer Laminating Printer Declaration of Conformity Machine Noise For USA onlyContents Do not touch the machine with wet hands Do not touch the power plug during electrical StormsDo not use a line voltage other than instructed Do not wet the machine with waterDo not touch the power plug with a wet hand Do not use the machine while it has a faultPull out the power plug before cleaning Machine Hold the body of the power plug when pulling it OutHandling of transfer film Ink ribbons and cards Product featuresChecking accessories Before useInstallation Names of parts Set the Scsi ID Connecting with a host computerSet the BUS switches Set-upConnect the IC unit with the host computer Connecting the IC unit Sold separatelyConnect the printer and IC unit Connect the compact IC unit to the host computer Connecting the power cordPlug the power cable into the printer Compact IC unit sold separatelyDischarging the card Installing the card stackerMount the card stacker on the printer Hang the stacker claw on the stacker receptacleWind the ribbon, taking up the slack Setting the ink ribbonRemove the ink ribbon cassette Place the cassette upright on a flat surface during set-upClose the printer door When the ink ribbon is wound up to the endInsert the cassette along the guide rail Remove the retransfer film cassette Setting the retransfer filmOpen the printer door and insert the cassette Setting the number of frames to be usedWhen the retransfer film is wound up to the end Wind the retransfer film to take up the slackOpen the card tray Setting cardsClose the card tray Card bracket locks when it reaches the holeInserting cards Unit can take about 300 0.76mm-thick cards Pull the card bracket backFor ISO cards When using magnetic cards Loading cardsWhen using contact IC cards For JIS II cardsRemove the blue securing screw Switching the card thicknessRemove the card thickness switching plate Malfunction of the printerNames of parts on the operation Panel LCD operation display content Operation display LED contents LCD panelOperation Turning on the power Initialized without winding up. Default Turning off the powerAbout the Reset button Turn off the printer’s powerUser modes User mode screen flowMain menu Submenu User mode settingsDisplay mode settings Clearing the free counter Cleaning modePress Enter to reset Exit user modeInk mode setting Set the retransfer speed Retransfer mode settingSet the retransfer temperature Set retransfer filmBuzzer mode setting Setting the bend remedy mode Test print Card size setting modeAntimagnetic setting mode Transport modeRemove the cleaning unit Care and cleaningCleaning the cleaning rollers Wipe the head indicated with horizontally Cleaning the thermal headHow to attach the sponge Cleaning the fan filter on the back sideTurn off the power after the cleaning card is discharged Cleaning the card feed rollersSet a cleaning card From user mode select cleaning modeSet the card on the card tray Cleaning the card feed rollers Heat rollersOnce printer servicing and cleaning Have been completed Apply alcohol on the magnetic head cleaning cardCard turnover table TroubleshootingCleaning rollers Layout of rollers inside the printerMeaning of reset → enter buttons in the list is Error code listingTroubleshooting Mending broken ink ribbon Retransfer film About printing errorsPush the card tray back into position on an angle Removing card jamsReturn the card tray to its original position Remove the card Remove any jammed cardsJog lever are supplied as standard Turn the jog dialMain specifications SpecificationsUnit/mm External appearance and dimensionsFront view Ultra Electronics Card Systems
Top Page Image Contents