Ultra electronic ID Card Printer manual Removing card jams

Page 45

Troubleshooting (continued)

Removing card jams

To determine the part of the machine affected by a card jam refer to the error code on the operation panel LCD on the printer and the relevant page in this manual.

When removing a jammed card, make sure that the power switch is set off before carrying out the following procedure.

Hopper jam

1. Pull out the card tray.

To remove the card tray, pull it out toward you until it no longer moves and lift it.

2. Remove the jammed cards.

If you can hold the jammed card, pull it out.

If you cannot hold the jammed card: Pull out a small portion of the cleaning unit.

Turn the right knob to drop the jammed card. Remove the fallen card.

3. Return the card tray to its original position.

Push the card tray back into position on an angle.

Push the card tray back into its position while placing the card tray tabs on the folded over metal plates.

CAUTION

Pushing the tray with excessive force may cause a failure of the printer.

Image 45

Contents ID Card Printer Magicard Prima Re-transfer Laminating Printer Declaration of Conformity Machine Noise For USA onlyContents Do not use a line voltage other than instructed Do not touch the power plug during electrical StormsDo not wet the machine with water Do not touch the machine with wet handsPull out the power plug before cleaning Machine Do not use the machine while it has a faultHold the body of the power plug when pulling it Out Do not touch the power plug with a wet handChecking accessories Product featuresBefore use Handling of transfer film Ink ribbons and cardsInstallation Names of parts Set the BUS switches Connecting with a host computerSet-up Set the Scsi IDConnecting the IC unit Sold separately Connect the printer and IC unitConnect the IC unit with the host computer Plug the power cable into the printer Connecting the power cordCompact IC unit sold separately Connect the compact IC unit to the host computerMount the card stacker on the printer Installing the card stackerHang the stacker claw on the stacker receptacle Discharging the cardRemove the ink ribbon cassette Setting the ink ribbonPlace the cassette upright on a flat surface during set-up Wind the ribbon, taking up the slackWhen the ink ribbon is wound up to the end Insert the cassette along the guide railClose the printer door Remove the retransfer film cassette Setting the retransfer filmWhen the retransfer film is wound up to the end Setting the number of frames to be usedWind the retransfer film to take up the slack Open the printer door and insert the cassetteOpen the card tray Setting cardsInserting cards Unit can take about 300 0.76mm-thick cards Card bracket locks when it reaches the holePull the card bracket back Close the card trayWhen using contact IC cards When using magnetic cards Loading cardsFor JIS II cards For ISO cardsRemove the card thickness switching plate Switching the card thicknessMalfunction of the printer Remove the blue securing screwNames of parts on the operation Panel LCD operation display content Operation display LED contents LCD panelOperation Turning on the powerAbout the Reset button Turning off the powerTurn off the printer’s power Initialized without winding up. DefaultUser modes User mode screen flowMain menu Submenu User mode settingsDisplay mode settings Press Enter to reset Cleaning modeExit user mode Clearing the free counterInk mode setting Set the retransfer temperature Retransfer mode settingSet retransfer film Set the retransfer speedBuzzer mode setting Setting the bend remedy mode Antimagnetic setting mode Card size setting modeTransport mode Test printCare and cleaning Cleaning the cleaning rollersRemove the cleaning unit Wipe the head indicated with horizontally Cleaning the thermal headHow to attach the sponge Cleaning the fan filter on the back sideSet a cleaning card Cleaning the card feed rollersFrom user mode select cleaning mode Turn off the power after the cleaning card is dischargedOnce printer servicing and cleaning Have been completed Cleaning the card feed rollers Heat rollersApply alcohol on the magnetic head cleaning card Set the card on the card trayCleaning rollers TroubleshootingLayout of rollers inside the printer Card turnover tableMeaning of reset → enter buttons in the list is Error code listingTroubleshooting Mending broken ink ribbon Retransfer film About printing errorsRemoving card jams Return the card tray to its original positionPush the card tray back into position on an angle Jog lever are supplied as standard Remove any jammed cardsTurn the jog dial Remove the cardMain specifications SpecificationsExternal appearance and dimensions Front viewUnit/mm Ultra Electronics Card Systems