Ultra electronic ID Card Printer manual Cleaning the card feed rollers Heat rollers

Page 40

Cleaning the card feed rollers and

heat rollers

Dirty magnetic head will cause a write/read error. It is recommended to clean the magnetic head after printing about 1,000 cards. Cleaning the magnetic head is not necessary if the magnetic stripe card is not used.

1. Keep the ink ribbon and retransfer film cassettes in their mounting positions.

See p.14 to p.18 of this manual.

2. Turn on the power of the printer.

Go to the next step when the printer is in the Preheat or Ready state.

3. Specify the “cleaning” mode in the user mode.

See p.26 in this manual.

> U s e r M o d e

MENU

> C l e a n i n g >

5. Set the card on the card tray.

Place the card in right direction. See p.20.

6. Press the ENTER button, select “MG Head” with the ↑ or ↓ button, and press the ENTER button.

> > M G H e a d

O K ?

ENTER

C l e a n i n g . .

7. When the cleaning card is discharged, turn off the power of the printer.

Wait for 10 seconds before turning on the power again.

CAUTION

Replace the magnetic head cleaning card when it gets dirty. A dirty card may pollute the head and cause damages to the head. Consult your dealer on the alcohol and cleaning card.

4. Apply alcohol on the magnetic head cleaning card.

Drip three or four drops of alcohol on the magnetic stripes.

Alcohol (sold separately)

Magnetic head cleaning card (sold separately)

Once printer servicing and cleaning

have been completed

Once servicing and cleaning of the printer have been completed, check to make sure that all parts have been replaced properly.

Improper replacement of parts may result in the power not turning on or in operating errors.

39

Image 40

Contents ID Card Printer Magicard Prima Re-transfer Laminating Printer Declaration of Conformity For USA only Machine NoiseContents Do not touch the power plug during electrical Storms Do not use a line voltage other than instructedDo not wet the machine with water Do not touch the machine with wet handsDo not use the machine while it has a fault Pull out the power plug before cleaning MachineHold the body of the power plug when pulling it Out Do not touch the power plug with a wet handProduct features Checking accessoriesBefore use Handling of transfer film Ink ribbons and cardsInstallation Names of parts Connecting with a host computer Set the BUS switchesSet-up Set the Scsi IDConnect the printer and IC unit Connecting the IC unit Sold separatelyConnect the IC unit with the host computer Connecting the power cord Plug the power cable into the printerCompact IC unit sold separately Connect the compact IC unit to the host computerInstalling the card stacker Mount the card stacker on the printerHang the stacker claw on the stacker receptacle Discharging the cardSetting the ink ribbon Remove the ink ribbon cassettePlace the cassette upright on a flat surface during set-up Wind the ribbon, taking up the slackInsert the cassette along the guide rail When the ink ribbon is wound up to the endClose the printer door Setting the retransfer film Remove the retransfer film cassetteSetting the number of frames to be used When the retransfer film is wound up to the endWind the retransfer film to take up the slack Open the printer door and insert the cassetteSetting cards Open the card trayCard bracket locks when it reaches the hole Inserting cards Unit can take about 300 0.76mm-thick cardsPull the card bracket back Close the card trayWhen using magnetic cards Loading cards When using contact IC cardsFor JIS II cards For ISO cardsSwitching the card thickness Remove the card thickness switching plateMalfunction of the printer Remove the blue securing screwNames of parts on the operation Panel Operation display LED contents LCD panel LCD operation display contentTurning on the power OperationTurning off the power About the Reset buttonTurn off the printer’s power Initialized without winding up. DefaultUser mode screen flow User modesUser mode settings Main menu SubmenuDisplay mode settings Cleaning mode Press Enter to resetExit user mode Clearing the free counterInk mode setting Retransfer mode setting Set the retransfer temperatureSet retransfer film Set the retransfer speedBuzzer mode setting Setting the bend remedy mode Card size setting mode Antimagnetic setting modeTransport mode Test printCleaning the cleaning rollers Care and cleaningRemove the cleaning unit Cleaning the thermal head Wipe the head indicated with horizontallyCleaning the fan filter on the back side How to attach the spongeCleaning the card feed rollers Set a cleaning cardFrom user mode select cleaning mode Turn off the power after the cleaning card is dischargedCleaning the card feed rollers Heat rollers Once printer servicing and cleaning Have been completedApply alcohol on the magnetic head cleaning card Set the card on the card trayTroubleshooting Cleaning rollersLayout of rollers inside the printer Card turnover tableError code listing Meaning of reset → enter buttons in the list isTroubleshooting About printing errors Mending broken ink ribbon Retransfer filmReturn the card tray to its original position Removing card jamsPush the card tray back into position on an angle Remove any jammed cards Jog lever are supplied as standardTurn the jog dial Remove the cardSpecifications Main specificationsFront view External appearance and dimensionsUnit/mm Ultra Electronics Card Systems