Ultra electronic ID Card Printer manual Display mode settings

Page 29

Operation (continued)

Display mode settings

The unit has the following three settings for the display mode. Allows selection of which counter value is displayed when the power is turned on.

CAUTION

The beep sounds when pressing the Enter button to save the settings in the user setting mode.

The beep will not sound if the buzzer mode setting (see p.32) is set to off.

> D i s p l a y >

ENTER

EXIT

To exit user mode

> > C o u n t e r			Counter select mode
> > C o u n t e r			3 options (Total, Head, Free)
	T o t a l		3 options (Total, Head, Free)

EXIT	MENU		ENTER
	Press	to select the setting and press		to save.
			(The electronic
		Counter selection	beep sounds .)
		Counter selection

Free counter (Free)

This allows the user to clear the counter. Displays the number of cards which have been printed correctly.

Head counter (Head)

Displays the number of printing colors in one Head.

The head counter cannot be reset.

Total counter (Total)

Displays the number of cards in total which have been printed correctly. The total counter cannot be reset.

> > C o n t r a s t		LCD contrast setting
> > C o n t r a s t		There are 7 gradations
		(–3 to +3, the higher the value the stronger the contrast.)
		- 2
EXIT	MENU		ENTER
EXIT	MENU	Press	to select the setting and press	to save.
			(The electronic
			beep sounds .)

		LCD background		SKY BLUE, BLUE, LIGHT BLUE,
> > B a c k	C o l o r	color settings:		GREEN, BRIGHT GREEN,
		8 options		YELLOW, PURPLE, PINK
		B L U E
EXIT	MENU			ENTER
		Press	to select the setting and press		to save.
				(The electronic
				beep sounds .)

28

Image 29

Contents ID Card Printer Magicard Prima Re-transfer Laminating Printer Declaration of Conformity Machine Noise For USA onlyContents Do not use a line voltage other than instructed Do not touch the power plug during electrical StormsDo not wet the machine with water Do not touch the machine with wet handsPull out the power plug before cleaning Machine Do not use the machine while it has a faultHold the body of the power plug when pulling it Out Do not touch the power plug with a wet handChecking accessories Product featuresBefore use Handling of transfer film Ink ribbons and cardsInstallation Names of parts Set the BUS switches Connecting with a host computerSet-up Set the Scsi IDConnect the IC unit with the host computer Connecting the IC unit Sold separatelyConnect the printer and IC unit Plug the power cable into the printer Connecting the power cordCompact IC unit sold separately Connect the compact IC unit to the host computerMount the card stacker on the printer Installing the card stackerHang the stacker claw on the stacker receptacle Discharging the cardRemove the ink ribbon cassette Setting the ink ribbonPlace the cassette upright on a flat surface during set-up Wind the ribbon, taking up the slackClose the printer door When the ink ribbon is wound up to the endInsert the cassette along the guide rail Remove the retransfer film cassette Setting the retransfer filmWhen the retransfer film is wound up to the end Setting the number of frames to be usedWind the retransfer film to take up the slack Open the printer door and insert the cassetteOpen the card tray Setting cardsInserting cards Unit can take about 300 0.76mm-thick cards Card bracket locks when it reaches the holePull the card bracket back Close the card trayWhen using contact IC cards When using magnetic cards Loading cardsFor JIS II cards For ISO cardsRemove the card thickness switching plate Switching the card thicknessMalfunction of the printer Remove the blue securing screwNames of parts on the operation Panel LCD operation display content Operation display LED contents LCD panelOperation Turning on the power About the Reset button Turning off the power Turn off the printer’s power Initialized without winding up. DefaultUser modes User mode screen flowMain menu Submenu User mode settingsDisplay mode settings Press Enter to reset Cleaning modeExit user mode Clearing the free counterInk mode setting Set the retransfer temperature Retransfer mode settingSet retransfer film Set the retransfer speedBuzzer mode setting Setting the bend remedy mode Antimagnetic setting mode Card size setting modeTransport mode Test printRemove the cleaning unit Care and cleaningCleaning the cleaning rollers Wipe the head indicated with horizontally Cleaning the thermal headHow to attach the sponge Cleaning the fan filter on the back sideSet a cleaning card Cleaning the card feed rollersFrom user mode select cleaning mode Turn off the power after the cleaning card is dischargedOnce printer servicing and cleaning Have been completed Cleaning the card feed rollers Heat rollersApply alcohol on the magnetic head cleaning card Set the card on the card trayCleaning rollers TroubleshootingLayout of rollers inside the printer Card turnover tableMeaning of reset → enter buttons in the list is Error code listingTroubleshooting Mending broken ink ribbon Retransfer film About printing errorsPush the card tray back into position on an angle Removing card jamsReturn the card tray to its original position Jog lever are supplied as standard Remove any jammed cardsTurn the jog dial Remove the cardMain specifications SpecificationsUnit/mm External appearance and dimensionsFront view Ultra Electronics Card Systems