Ultra electronic ID Card Printer manual Buzzer mode setting

Page 33

Operation (continued)

Buzzer mode setting

Power saving mode settings

The buzzer indicating errors can be turned on or off.

> B u z z e r

EXIT

Exit user mode

O n

Set the buzzer:

there are two settings

(On, off)

ENTER

Press to select the setting and press to save.

(The electronic beep sounds.)

When Off is specified,

electronic beep sound indicating an error,

electronic beep sound indicating the number of cards, and

electronic beep sound indicating settings saved with

the ENTER button in the user mode are muted.

The printer enters into the power save mode after a specified period of time if none of operation buttons are touched in the Ready state. The heat roller for retransfer, bend remedial roller, and LCD back- panel are turned off in the power save mode.

> P o w e r S a v i n g

EXIT

Exit user mode

o f f

Power saving settings:

there are 9 options.

Press	to select the	ENTER
Press	setting and press	to save.
	setting and press

(The electronic beep sounds.)

Press the EXIT button to cancel the user mode, and the printer starts.

Off:

Not in power saving mode.

Setting options: [5,10,20,25,30,45,60] (units: minutes)

[5,10,15,20,25,30,45,60] (units: minutes)

If printing is not to be carried out for a period longer that the set time, switch the unitís heater off. (Power save status)

“Sleeping” appears on the LCD panel in the power save mode. The operation buttons are disabled in this mode. See step 2 in “Canceling the power save mode” to enable the operation buttons.

S l e e p i n g

The printer moves to the power save mode when the specified time arrives even if you turns off the printer and turn it on again.

32

Canceling the power save mode 1. From the host computer

Enter a control command to print the card. The power save mode is cancelled, and printing automatically starts upon completion of preheating.

2. Temporary cancellation

To cancel the power save mode temporarily on the printer, press RESET, then ENTER to initialize the printer.

3. Permanent cancellation

Cancel the power save mode temporarily as described in step 2, and change the power save mode setting to OFF.

Image 33

Contents ID Card Printer Magicard Prima Re-transfer Laminating Printer Declaration of Conformity Machine Noise For USA onlyContents Do not use a line voltage other than instructed Do not touch the power plug during electrical StormsDo not wet the machine with water Do not touch the machine with wet handsPull out the power plug before cleaning Machine Do not use the machine while it has a faultHold the body of the power plug when pulling it Out Do not touch the power plug with a wet handChecking accessories Product featuresBefore use Handling of transfer film Ink ribbons and cardsInstallation Names of parts Set the BUS switches Connecting with a host computerSet-up Set the Scsi IDConnecting the IC unit Sold separately Connect the printer and IC unitConnect the IC unit with the host computer Plug the power cable into the printer Connecting the power cordCompact IC unit sold separately Connect the compact IC unit to the host computerMount the card stacker on the printer Installing the card stackerHang the stacker claw on the stacker receptacle Discharging the cardRemove the ink ribbon cassette Setting the ink ribbonPlace the cassette upright on a flat surface during set-up Wind the ribbon, taking up the slackWhen the ink ribbon is wound up to the end Insert the cassette along the guide railClose the printer door Remove the retransfer film cassette Setting the retransfer filmWhen the retransfer film is wound up to the end Setting the number of frames to be usedWind the retransfer film to take up the slack Open the printer door and insert the cassetteOpen the card tray Setting cardsInserting cards Unit can take about 300 0.76mm-thick cards Card bracket locks when it reaches the holePull the card bracket back Close the card trayWhen using contact IC cards When using magnetic cards Loading cardsFor JIS II cards For ISO cardsRemove the card thickness switching plate Switching the card thicknessMalfunction of the printer Remove the blue securing screwNames of parts on the operation Panel LCD operation display content Operation display LED contents LCD panelOperation Turning on the powerAbout the Reset button Turning off the powerTurn off the printer’s power Initialized without winding up. DefaultUser modes User mode screen flowMain menu Submenu User mode settingsDisplay mode settings Press Enter to reset Cleaning modeExit user mode Clearing the free counterInk mode setting Set the retransfer temperature Retransfer mode settingSet retransfer film Set the retransfer speedBuzzer mode setting Setting the bend remedy mode Antimagnetic setting mode Card size setting modeTransport mode Test printCare and cleaning Cleaning the cleaning rollersRemove the cleaning unit Wipe the head indicated with horizontally Cleaning the thermal headHow to attach the sponge Cleaning the fan filter on the back sideSet a cleaning card Cleaning the card feed rollersFrom user mode select cleaning mode Turn off the power after the cleaning card is dischargedOnce printer servicing and cleaning Have been completed Cleaning the card feed rollers Heat rollersApply alcohol on the magnetic head cleaning card Set the card on the card trayCleaning rollers TroubleshootingLayout of rollers inside the printer Card turnover tableMeaning of reset → enter buttons in the list is Error code listingTroubleshooting Mending broken ink ribbon Retransfer film About printing errorsRemoving card jams Return the card tray to its original positionPush the card tray back into position on an angle Jog lever are supplied as standard Remove any jammed cardsTurn the jog dial Remove the cardMain specifications SpecificationsExternal appearance and dimensions Front viewUnit/mm Ultra Electronics Card Systems