Ultra electronic ID Card Printer manual Setting the ink ribbon, Remove the ink ribbon cassette

Page 15

Set-up(continued)

Setting the ink ribbon

CAUTION

Do not touch the surface of the ribbon with your hands.

1. Activate the slide knob and open the printer door.

3. Insert the ink ribbon into the cassette.

Stretch the ink ribbon along three shafts with the ink face of the ribbon facing outside and insert the bobbins firmly into the bobbin holders.

Feed spool (yellow bobbin)

When the slide knob is moved, the printer door opens downwards. Hold the door with your hand and open it slowly.

Shaft

Bobbin holder (yellow)

Ink face

Wind spool (black bobbin)

Ink ribbon cassette (yellow)

CAUTION

Do not put the ink ribbon or retransfer film on the back of the door for mounting. Do not rest your elbows or put a heavy thing on the back of the door. The printer door may be broken.

2. Remove the ink ribbon cassette.

When the lever is pressed, a small portion of the cassette pops out.

Cushion	Press the removal lever.

CAUTION

When transporting the unit, remove the ink ribbon and the retransfer film, then place the cushion on the thermal head. Transporting without the cushion may cause the thermal head and roller to malfunction.

Do not use cushion materials other than the transfer cushion that comes with the unit, as this may cause damage to the head.

14

(do not touch the surface)

Bobbin holder (black)

Place the cassette upright on a flat surface during set-up.

CAUTION

When you need to take out the cassette, for instance, to clean the printer, be sure to put the cassette upright as shown in the above illustration. When the ink ribbon is put on the table with its face down, dusts attach to the surface, causing a malfunction of the printer.

4. Wind the ribbon, taking up the slack.

Turn the knob in the arrow direction to wind a small portion of the ink ribbon. If the ink ribbon does not wind up, go back to step 3, and insert the ink ribbon firmly into the bobbin holders.

CAUTION If the ink ribbon is not tightly wound, the slack may cause the ribbon to be caught in the parts of the printer when you set the cassette, or the card to be printed in uneven colors.

Image 15

Contents ID Card Printer Magicard Prima Re-transfer Laminating Printer Declaration of Conformity Machine Noise For USA onlyContents Do not touch the machine with wet hands Do not touch the power plug during electrical StormsDo not use a line voltage other than instructed Do not wet the machine with waterDo not touch the power plug with a wet hand Do not use the machine while it has a faultPull out the power plug before cleaning Machine Hold the body of the power plug when pulling it OutHandling of transfer film Ink ribbons and cards Product featuresChecking accessories Before useInstallation Names of parts Set the Scsi ID Connecting with a host computerSet the BUS switches Set-upConnecting the IC unit Sold separately Connect the printer and IC unitConnect the IC unit with the host computer Connect the compact IC unit to the host computer Connecting the power cordPlug the power cable into the printer Compact IC unit sold separatelyDischarging the card Installing the card stackerMount the card stacker on the printer Hang the stacker claw on the stacker receptacleWind the ribbon, taking up the slack Setting the ink ribbonRemove the ink ribbon cassette Place the cassette upright on a flat surface during set-upWhen the ink ribbon is wound up to the end Insert the cassette along the guide railClose the printer door Remove the retransfer film cassette Setting the retransfer filmOpen the printer door and insert the cassette Setting the number of frames to be usedWhen the retransfer film is wound up to the end Wind the retransfer film to take up the slackOpen the card tray Setting cardsClose the card tray Card bracket locks when it reaches the holeInserting cards Unit can take about 300 0.76mm-thick cards Pull the card bracket backFor ISO cards When using magnetic cards Loading cardsWhen using contact IC cards For JIS II cardsRemove the blue securing screw Switching the card thicknessRemove the card thickness switching plate Malfunction of the printerNames of parts on the operation Panel LCD operation display content Operation display LED contents LCD panelOperation Turning on the power Initialized without winding up. Default Turning off the powerAbout the Reset button Turn off the printer’s powerUser modes User mode screen flowMain menu Submenu User mode settingsDisplay mode settings Clearing the free counter Cleaning modePress Enter to reset Exit user modeInk mode setting Set the retransfer speed Retransfer mode settingSet the retransfer temperature Set retransfer filmBuzzer mode setting Setting the bend remedy mode Test print Card size setting modeAntimagnetic setting mode Transport modeCare and cleaning Cleaning the cleaning rollersRemove the cleaning unit Wipe the head indicated with horizontally Cleaning the thermal headHow to attach the sponge Cleaning the fan filter on the back sideTurn off the power after the cleaning card is discharged Cleaning the card feed rollersSet a cleaning card From user mode select cleaning modeSet the card on the card tray Cleaning the card feed rollers Heat rollersOnce printer servicing and cleaning Have been completed Apply alcohol on the magnetic head cleaning cardCard turnover table TroubleshootingCleaning rollers Layout of rollers inside the printerMeaning of reset → enter buttons in the list is Error code listingTroubleshooting Mending broken ink ribbon Retransfer film About printing errorsRemoving card jams Return the card tray to its original positionPush the card tray back into position on an angle Remove the card Remove any jammed cardsJog lever are supplied as standard Turn the jog dialMain specifications SpecificationsExternal appearance and dimensions Front viewUnit/mm Ultra Electronics Card Systems