Ultra electronic ID Card Printer manual Cleaning the card feed rollers, Set a cleaning card

Page 39

Cleaning the card feed rollers

5. Set a cleaning card.

Dirty rollers are the major cause of jamming of the cards. It is recommended to clean the rollers once after printing about 1,000 cards. It is also recommended to carry out cleaning before the work, because the retransfer roller (heat roller) does not operate while it is hot.

1. Remove the retransfer film cassette.

See p.16 in this manual.

2. Turn on the power of the printer.

The printer initializes, and the [No Cassette] error is indicated.

3. From user mode select cleaning mode.

> U s e r M o d e

MENU

> C l e a n i n g >

4. Press the ENTER button. Select [Rollers] with

↑and ↓ buttons, and press the ENTER button.

See p.26 in this manual.

> > R o l l e r s

O K ?

Peel off the protective paper from both sides of the cleaning card and insert it into the card discharge slot. The card will be drawn into the unit by the rollers and cleaning will then be carried out. Insert the card with its adhesive face upside down to repeat the cleaning procedure once more.

Cleaning card (accessory)

The cleaning card can be inserted only from the right side.

NG card discharge slot

CAUTION

• If the retransfer roller (heat roller)

gets too hot,

H R i s t o o h o t !

appears on the LCD panel, and the printer returns to the Ready state.

Turn off the power of the printer, and wait until the roller completely cools down before starting the work. Confirm that the retransfer film cassette has been removed.

•The cleaning card does not go into the card discharge slot at the left side.

•If a card jam occurs, turn off the power, then turn on the power again. The jammed card will be discarded.

ENTER

C l e a n i n g . .

S t a r t O K ?

ENTER

C l e a n i n g . .

6. Turn off the power after the cleaning card is discharged.

Wait for 10 seconds before turning on the power again.

CAUTION

The cleaning card can be used only once. If you use the dirty cleaning card many times, the dirt on the card moves onto the rollers, causing damages to the rollers.

Consult your dealer for the cleaning card.

Insert the cleaning card in about 10 seconds. If you fails to set the card within this time, the printer returns to “Start OK?” Press the ENTER button again to proceed.

38

Image 39

Contents ID Card Printer Magicard Prima Re-transfer Laminating Printer Declaration of Conformity Machine Noise For USA onlyContents Do not touch the machine with wet hands Do not touch the power plug during electrical StormsDo not use a line voltage other than instructed Do not wet the machine with waterDo not touch the power plug with a wet hand Do not use the machine while it has a faultPull out the power plug before cleaning Machine Hold the body of the power plug when pulling it OutHandling of transfer film Ink ribbons and cards Product featuresChecking accessories Before useInstallation Names of parts Set the Scsi ID Connecting with a host computerSet the BUS switches Set-upConnecting the IC unit Sold separately Connect the printer and IC unitConnect the IC unit with the host computer Connect the compact IC unit to the host computer Connecting the power cordPlug the power cable into the printer Compact IC unit sold separatelyDischarging the card Installing the card stackerMount the card stacker on the printer Hang the stacker claw on the stacker receptacleWind the ribbon, taking up the slack Setting the ink ribbonRemove the ink ribbon cassette Place the cassette upright on a flat surface during set-upWhen the ink ribbon is wound up to the end Insert the cassette along the guide railClose the printer door Remove the retransfer film cassette Setting the retransfer filmOpen the printer door and insert the cassette Setting the number of frames to be usedWhen the retransfer film is wound up to the end Wind the retransfer film to take up the slackOpen the card tray Setting cardsClose the card tray Card bracket locks when it reaches the holeInserting cards Unit can take about 300 0.76mm-thick cards Pull the card bracket backFor ISO cards When using magnetic cards Loading cardsWhen using contact IC cards For JIS II cardsRemove the blue securing screw Switching the card thicknessRemove the card thickness switching plate Malfunction of the printerNames of parts on the operation Panel LCD operation display content Operation display LED contents LCD panelOperation Turning on the power Initialized without winding up. Default Turning off the powerAbout the Reset button Turn off the printer’s powerUser modes User mode screen flowMain menu Submenu User mode settingsDisplay mode settings Clearing the free counter Cleaning modePress Enter to reset Exit user modeInk mode setting Set the retransfer speed Retransfer mode settingSet the retransfer temperature Set retransfer filmBuzzer mode setting Setting the bend remedy mode Test print Card size setting modeAntimagnetic setting mode Transport modeCare and cleaning Cleaning the cleaning rollersRemove the cleaning unit Wipe the head indicated with horizontally Cleaning the thermal headHow to attach the sponge Cleaning the fan filter on the back sideTurn off the power after the cleaning card is discharged Cleaning the card feed rollersSet a cleaning card From user mode select cleaning modeSet the card on the card tray Cleaning the card feed rollers Heat rollersOnce printer servicing and cleaning Have been completed Apply alcohol on the magnetic head cleaning cardCard turnover table TroubleshootingCleaning rollers Layout of rollers inside the printerMeaning of reset → enter buttons in the list is Error code listingTroubleshooting Mending broken ink ribbon Retransfer film About printing errorsRemoving card jams Return the card tray to its original positionPush the card tray back into position on an angle Remove the card Remove any jammed cardsJog lever are supplied as standard Turn the jog dialMain specifications SpecificationsExternal appearance and dimensions Front viewUnit/mm Ultra Electronics Card Systems